Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2015.08–2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0217079 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of Skid control ECU (Brake actuator assembly) Perform yaw rate and acceleration sensor zero point calibration and store system information.
·

VSC disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 4.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C324706C01
0.573,1.021 1.375,1.021 true 0.646,1.469 1.302,1.469 1.302,1.469 1.615,1.219 true 1.365,1.708 1.51,1.708 1.51,1.708 1.896,1.323 true 2.177,1.521 2.969,1.521 true 0.917,2.479 0.917,1.833 true 1.604,2.333 2.031,2.333 true 0.313,0.917 0.542,1.125 0.229,0.208 10 true *a 0.417,1.365 0.615,1.563 0.198,0.198 10 true *b 1.219,1.604 1.406,1.813 0.188,0.208 10 true *c 3.031,1.417 3.24,1.625 0.208,0.208 10 true *c 0.854,2.521 1.063,2.74 0.208,0.219 10 true *d 2.083,2.25 2.292,2.448 0.208,0.198 10 true *d
*a To Front Wheel Cylinder RH
*b To Front Wheel Cylinder LH
*c To Rear Wheel Cylinder
*d From Master Cylinder


Place tags or marks to identify the installation locations of each brake line.


b.
C324707C01
0,0 0,0 false
V113147

Lock Lever Released
V113148

Connector Disconnected


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.

Detach the clamp from the brake actuator bracket assembly.


d.
C324708

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


e.

Remove the 3 nuts and brake actuator with bracket.

NOTICE:
C324709

Do not damage the brake lines.