Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.08–2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0213502 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1268  Transfer L4 Position Switch Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1268 Transfer L4 Position Switch Circuit Either of the following is detected:
1.

No signal is input to the EXI4 terminal of the skid control ECU.

2.

The skid control ECU receives an L4 abnormal status signal from the 4 wheel drive control ECU via CAN.


·

L4 detection switch (Transfer shift actuator assembly)

·

L4 detection switch circuit

·

Skid control ECU (Brake actuator assembly)

·

4 wheel drive control ECU

·

Touch select 2-4 and high-low system



WIRING DIAGRAM

C323123E07
0.75,3.896 2.302,4.313 1.552,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 0.823,3.698 1.24,3.958 0.417,0.26 10 false A4 0.927,2.365 1.344,2.625 0.417,0.26 10 false C60 0.938,2.552 2.656,2.99 1.719,0.438 10 false 4 Wheel Drive Control ECU 0.927,0.99 1.344,1.25 0.417,0.26 10 false C41 0.938,1.177 1.646,1.479 0.708,0.302 10 false ECM 2.26,3.271 2.677,3.531 0.417,0.26 10 false EXI4 2.146,1.938 2.583,2.177 0.438,0.24 10 false 4WDL 2.365,0.594 2.781,0.854 0.417,0.26 10 false L4 2.677,3.135 3.094,3.396 0.417,0.26 10 false 5 2.656,1.802 3.073,2.063 0.417,0.26 10 false 3 2.656,0.469 3.073,0.729 0.417,0.26 10 false 12 4.26,3.844 4.677,4.104 0.417,0.26 10 false C74 4.26,4.042 6.094,4.469 1.833,0.427 10 false L4 Detection Switch (Transfer Shift Actuator Assembly) 4.104,3.115 4.292,3.365 0.188,0.25 10 false 9 6.021,3.125 6.438,3.385 0.417,0.26 10 false 10 4.375,3.115 4.792,3.375 0.417,0.26 10 false L4 5.615,3.125 6.031,3.385 0.417,0.26 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


HINT:

When DTC U0114 is output together with DTC C1268, inspect and repair the trouble areas indicated by DTC U0114 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.INSPECT TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
a.

Turn the 4WD control switch (transfer position switch) to L4, and then drive the vehicle and check that there are no problems with the touch select 2-4 and high-low system.

OK:

There are no problems with the touch select 2-4 and high-low system.


Result:
Result
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (EXI4 TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (EXI4 TERMINAL)
a.

Connect the A4 skid control ECU (brake actuator assembly) connector.


b.

Turn the 4WD control switch (transfer position switch) to L4.


c.

Disconnect the C41 ECM connector.


d.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


C306843C63
1.521,0.094 1.885,0.313 0.365,0.219 1.365,0.854 1.094,0.281 1.094,0.281 0.927,0.281 false 0.625,0.208 1.01,0.406 0.385,0.198 10 false EXI4 0.063,0.042 0.448,0.24 0.385,0.198 10 false *a 1.604,0.115 1.99,0.313 0.385,0.198 10 false A4
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-5 (EXI4) - Body ground
·

Ignition switch ON

·

4WD control switch (transfer position switch) set to L4


Below 1.5 V



f.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


g.

Reconnect the C41 ECM connector.


h.

Turn the 4WD control switch (transfer position switch) to H2 or H4.


i.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


j.

Disconnect the C41 ECM connector.


k.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-5 (EXI4) - Body ground
·

Ignition switch ON

·

4WD control switch (transfer position switch) set to H2 or H4


11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXI4 CIRCUIT)

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


c.

Reconnect the C41 ECM connector.


d.

Turn the ignition switch to ON.


e.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

f.

Turn the ignition switch off.


g.

Start the engine.


h.

Turn the 4WD control switch (transfer position switch) to H2 or H4.


i.

Turn the 4WD control switch (transfer position switch) to L4, drive the vehicle, and then check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is output
DTC is not output




DTC is output

DTC is not output