The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
The brake fluid level is insufficient.
EBD operation is not possible.
The vacuum inside the brake booster decreases.
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| DTC is not output |
| DTC is output |
DTC is not output
DTC is output
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A4-12 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-25 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Brake Fluid Level Warning Switch [Brake Master Cylinder Reservoir Assembly]) |
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the A5 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Switch off (Float up) | 10 kΩ or higher |
| Switch on (Float down) | Below 1 Ω |
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G8 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-16 (SW) - A5-1 (+) | Always | Below 1 Ω |
| A5-2 (E) - Body ground | Always | Below 1 Ω |
| G8-16 (SW) or A5-1 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the vacuum warning switch assembly.
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH(for Diesel)>REMOVAL
Inspect the vacuum warning switch assembly.
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH(for Diesel)>ON-VEHICLE INSPECTION
The vacuum warning switch assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-9 (VCM) - A34-2 | Always | Below 1 Ω |
| A34-1 - Body ground | Always | Below 1 Ω |
| G8-9 (VCM) or A34-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reinstall the reservoir filler cap and strainer.
Reinstall the vacuum warning switch assembly.
Reconnect the G8 combination meter assembly connector, A4 skid control ECU (brake actuator assembly) connector and the A5 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Reconnect the A34 vacuum warning switch assembly connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Warning Light | Brake warning light | OFF or ON | OFF: Warning light off
ON: Warning light on |
- |
| Tester Display |
|---|
| Brake Warning Light |
Check the GTS display condition of the brake warning light.
| Proceed to |
|---|
| Display of the Data List remains OFF |
| Display of the Data List remains ON |
Display of the Data List remains OFF
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Display of the Data List remains ON