Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER HEAD › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231147 CYLINDER HEAD G

5L-E ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the surface of the cylinder head sub-assembly that contacts the cylinder block sub-assembly.

NOTICE:

Be careful not to scratch the surface of the cylinder head sub-assembly.



b.

Using a soft brush and solvent, thoroughly clean the cylinder head sub-assembly.


c.
A059164

Using a valve guide bushing brush and solvent, clean all the valve guide bushes.


Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.
A378632C01
0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 0.135,1.792 0.448,1.948 0.313,0.156 10 false *b 0.146,3.25 0.458,3.406 0.313,0.156 10 false *c
*a Cylinder Block Sub-assembly Side
*b Intake Manifold Side
*c Exhaust Manifold Side


Inspect the cylinder head sub-assembly for warpage.

i.

Using a precision straightedge and feeler gauge, measure the surfaces of the cylinder head sub-assembly that contact the cylinder block sub-assembly and manifolds for warpage.

Maximum warpage:

0.2 mm (0.00787 in.)


If the warpage is more than the maximum, replace the cylinder head sub-assembly.



b.

Inspect the cylinder head sub-assembly for cracks.

i.

Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block sub-assembly surface for cracks.

If there are cracks, replace the cylinder head sub-assembly.



Hide 3.CLEAN VALVE

a.

Using a gasket scraper, chip off any carbon from the valve head.


b.

Using a wire brush, thoroughly clean the valve.


Hide 13711 4.INSPECT INTAKE VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

7.975 to 7.990 mm (0.3140 to 0.3146 in.)


If the diameter is not as specified, replace the intake valve.


b.
A303230C06
3.073,1.802 3.385,2 0.313,0.198 10 false *a
*a Valve Face Angle


Check the valve face angle.

i.

Grind the valve enough to remove any pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°


If the result is not as specified, replace the intake valve.



c.
A303231C05
0.51,1.667 0.823,1.865 0.313,0.198 10 false *a
*a Margin Thickness


Check the valve head margin thickness.

Standard margin thickness:

1.6 mm (0.0630 in.)


Minimum margin thickness:

1.1 mm (0.0433 in.)


If the margin thickness is less than the minimum, replace the intake valve.


d.

Check the overall length of the valve.

Standard overall length:

104.1 to 104.5 mm (4.10 to 4.11 in.)


Minimum overall length:

103.6 mm (4.08 in.)


If the overall length is less than the minimum, replace the intake valve.


e.
A303232

Check the surface of the valve stem tip for wear.

If the valve stem tip is worn, resurface the tip with a grinder or replace the intake valve.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.



Hide 13715 5.INSPECT EXHAUST VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

7.960 to 7.975 mm (0.3134 to 0.3140 in.)


If the diameter is not as specified, replace the exhaust valve.


b.
A303230C06
3.073,1.802 3.385,2 0.313,0.198 10 false *a
*a Valve Face Angle


Check the valve face angle.

i.

Grind the valve enough to remove any pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°


If the valve face is worn, replace the exhaust valve.



c.
A303231C05
0.51,1.667 0.823,1.865 0.313,0.198 10 false *a
*a Margin Thickness


Check the valve head margin thickness.

Standard margin thickness:

1.7 mm (0.0669 in.)


Minimum margin thickness:

1.2 mm (0.0472 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


d.

Check the overall length of the valve.

Standard overall length:

103.95 to 104.35 mm (4.09 to 4.11 in.)


Minimum overall length:

103.45 mm (4.07 in.)


If the overall length is less than the minimum, replace the exhaust valve.


e.
A303232

Check the surface of the valve stem tip for wear.

If the valve stem tip is worn, resurface the tip with a grinder or replace the exhaust valve.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.



Hide 13711B 6.INSPECT INNER COMPRESSION SPRING

a.
A303233C04
1.177,0.052 1.49,0.25 0.313,0.198 10 false *a
*a Deviation


Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

2.0 mm (0.0787 in.)


If the deviation is more than the maximum, replace the inner compression spring.


b.
EM00801

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:

46.2 mm (1.82 in.)


If the free length is not as specified, replace the inner compression spring.


c.
EM00281

Using a spring tester, measure the tension of the inner compression spring at the specified installed length.

Standard tension:

301 to 332 N (31 to 34 kgf, 66.6 to 74.6 lbf) at 37.00 mm (1.46 in.)


If the tension is not as specified, replace the inner compression spring.


Hide 11122 7.INSPECT INTAKE VALVE GUIDE BUSH

A303239

a.

Using a caliper gauge, measure the inside diameter of the intake valve guide bush.

Standard bush inside diameter:

8.01 to 8.03 mm (0.315 to 0.316 in.)



b.

Subtract the valve stem diameter measurement (refer to the intake valve inspection procedures above) from the intake valve guide bush inside diameter measurement.

Standard oil clearance:

0.02 to 0.055 mm (0.000787 to 0.00217 in.)


Maximum oil clearance:

0.08 mm (0.00315 in.)


If the oil clearance is more than the maximum, replace the intake valve and intake valve guide bush.


Hide 11126 8.INSPECT EXHAUST VALVE GUIDE BUSH

A303243

a.

Using a caliper gauge, measure the inside diameter of the exhaust valve guide bush.

Standard bush inside diameter:

8.01 to 8.03 mm (0.315 to 0.316 in.)



b.

Subtract the valve stem diameter measurement (refer to the exhaust valve inspection procedures above) from the exhaust valve guide bush inside diameter measurement.

Standard oil clearance:

0.035 to 0.07 mm (0.00138 to 0.00276 in.)


Maximum oil clearance:

0.1 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the exhaust valve and guide bush.


Hide 9.INSPECT INTAKE VALVE SEAT

a.
A057256C02
1.844,0.948 2.219,0.594 2.219,0.594 2.354,0.594 true 2.417,0.5 2.74,0.719 0.323,0.219 10 false *a
*a 45° Carbide Cutter


Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the valve seats.


b.
A057247C02
1.479,1.063 1.781,1.281 0.302,0.219 10 false *a
*a Width


Apply a light coat of Prussian blue to the valve face.


c.

Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve while pressing the valve against the valve seat.



d.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.5 and 1.9 mm (0.0591 and 0.0748 in.).

If the contact surfaces are not as specified, resurface the intake valve seat. If necessary, replace the intake valve.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If the contact surfaces are not as specified, resurface the intake valve seat. If necessary, replace the intake valve.



Hide 10.INSPECT EXHAUST VALVE SEAT

a.
A057255C01
1.677,0.875 2.01,0.458 2.01,0.458 2.177,0.458 true 2.229,0.354 2.542,0.552 0.313,0.198 10 false *a
*a 45° Carbide Cutter


Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the valve seats.


b.
A057246C02
1.521,1.104 1.792,1.292 0.271,0.188 10 false *a
*a Width


Apply a light coat of Prussian blue to the valve face.


c.

Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve while pressing the valve against the valve seat.



d.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.8 and 2.2 mm (0.0708 and 0.0866 in.)

If the contact surfaces are not as specified, resurface the exhaust valve seat. If necessary, replace the exhaust valve.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If the contact surfaces are not as specified, resurface the exhaust valve seat. If necessary, replace the exhaust valve.



Hide 13751 11.INSPECT VALVE LIFTER

a.
A058346

Using a micrometer, measure the valve lifter diameter.

Standard lifter diameter:

40.892 to 40.902 mm (1.6099 to 1.6103 in.)



b.
A057262

Using a caliper gauge, measure the valve lifter bore diameter of the cylinder head sub-assembly.

Standard lifter bore diameter:

40.96 to 40.98 mm (1.6126 to 1.6134 in.)



c.

Measure the oil clearance by subtracting the valve lifter diameter measurement from the valve lifter bore diameter measurement.

Standard oil clearance:

0.058 to 0.088 mm (0.00238 to 0.00346 in.)


Maximum oil clearance:

0.1 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve lifter. If necessary, replace the cylinder head sub-assembly.


Hide 12.INSPECT CAMSHAFT OIL CLEARANCE

Hide 13.INSPECT CAMSHAFT THRUST CLEARANCE