Home › Drivetrain › R151F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › from 2016.01
RM3270E _52 Drivetrain _048709 R151F MANUAL TRANSMISSION / TRANSAXLE _0231338 MANUAL TRANSMISSION UNIT A

R151F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 33101A 1.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C315152

Remove the manual transmission filler plug and gasket from the manual transmission case.


Hide 33104 2.REMOVE DRAIN PLUG SUB-ASSEMBLY

a.
C315153

Remove the drain plug sub-assembly and gasket from the manual transmission case.


Hide 31126 3.REMOVE CLUTCH RELEASE FORK BOOT

Hide 31230 4.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31236B 5.REMOVE RELEASE FORK SUPPORT

Hide 31111 6.REMOVE CLUTCH HOUSING

a.
C350147C01
0,0 0.313,0.156 0.313,0.156 10 false *A 0.01,2.458 0.323,2.615 0.313,0.156 10 false *B
*A for 2TR-FE
*B for 5L-E


Remove the 9 bolts.


b.
C325687

Using a plastic-faced hammer, tap off the clutch housing from the manual transmission case.


Hide 84210 7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

Hide 33280 8.REMOVE REVERSE RESTRICT PIN ASSEMBLY

a.
C344406

Remove the 2 reverse restrict pin assemblies from the transfer adapter sub-assembly.


Hide 33506F 9.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
C344407

Remove the 4 bolts.


b.

Remove the floor shift control shift lever retainer sub-assembly.


c.

Remove the control shift lever retainer gasket.


Hide 36107A 10.REMOVE TRANSFER ADAPTER SUB-ASSEMBLY

a.
C332420

Remove the 10 bolts and 2 wire harness brackets.


b.
C332421

Using a brass bar and a hammer, tap out the transfer adapter sub-assembly from the manual transmission case.


Hide 33251 11.REMOVE SHIFT AND SELECT LEVER

a.
C344408

Remove the bolt from the shift lever housing.


b.
C344409

Remove the shift and select lever and the shift lever housing from the transfer adapter sub-assembly.


Hide 33124E 12.REMOVE TRANSFER OIL RECEIVER PIPE

a.
C332422

Remove the transfer oil receiver pipe from the transfer adapter sub-assembly.


Hide 33283F 13.REMOVE REVERSE RESTRICT PIN

a.
C332423

Using a T40 ''TORX'' socket wrench, remove the plug.


b.
C332424

Using a 5 mm pin punch and hammer, tap out the reverse restrict slotted pin.


c.
C315159

Remove the reverse restrict pin.


Hide 33131 15.REMOVE FRONT BEARING RETAINER

a.
C315191

Remove the 8 bolts.


b.
C316268

Using a brass bar and hammer, tap off the front bearing retainer from the manual transmission case.


Hide 33131A 16.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

Hide 33311G 17.REMOVE FRONT BEARING SHAFT SNAP RING

a.
C315160

Using a snap ring expander, remove the front bearing shaft snap ring from the manual transmission case.


Hide 33411Q 18.REMOVE COUNTER GEAR FRONT BEARING SNAP RING

a.
C315161

Using a snap ring expander, remove the counter gear front bearing snap ring from the manual transmission case.


Hide 33111 19.REMOVE MANUAL TRANSMISSION CASE

a.
C315162

Using a brass bar and hammer, tap off the manual transmission case from the intermediate plate.


Hide 33449B 20.REMOVE TRANSMISSION MAGNET

a.
C315163

Remove the transmission magnet from the intermediate plate.


Hide 21.SECURE INTERMEDIATE PLATE

a.
C288239

Secure the intermediate plate in a vise between aluminum plates.


Hide 22.REMOVE SHIFT DETENT BALL PLUG

a.
C314572C03
1.625,2.208 1.938,2.406 0.313,0.198 10 false *b 0.594,2.219 0.906,2.417 0.313,0.198 10 false *a
*a for Type A
*b for Type B


Remove the shift detent ball plug from the intermediate plate.

i.

for Type A:

Using a T40 ''TORX'' socket wrench, remove the shift detent ball plug from the intermediate plate.


ii.

for Type B:

Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the intermediate plate.



b.
C315164

Using a magnet hand, remove the shift detent ball compression spring and shift detent ball from the intermediate plate.


c.
C314573C02
1.531,2.188 1.844,2.385 0.313,0.198 10 false *b 0.573,2.188 0.885,2.385 0.313,0.198 10 false *a
*a for Type A
*b for Type B


Remove the shift detent ball plug from the intermediate plate.

i.

for Type A:

Using a T40 ''TORX'' socket wrench, remove the 2 shift detent ball plugs from the intermediate plate.


ii.

for Type B:

Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the intermediate plate.



d.
C288241

Using a magnet hand, remove the 2 shift detent ball compression springs and 2 shift detent balls from the intermediate plate.


Hide 33243A 23.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
C288242

Using 2 screwdrivers and a hammer, tap off the shift fork shaft snap ring from the No. 2 gear shift fork shaft.

NOTICE:

Use a cloth to prevent the shift fork shaft snap ring from flying off.



b.
C288243

Remove the bolt from the No. 2 gear shift fork.


c.
C288244

Remove the No. 2 gear shift fork shaft from the intermediate plate.


d.
C288245

Remove the No. 2 gear shift fork from the No. 2 transmission hub sleeve.


e.
C325699

Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.


Hide 33242 24.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
C288246

Using 2 screwdrivers and a hammer, tap off the shift fork shaft snap ring from the No. 1 gear shift fork shaft.

NOTICE:

Use a cloth to prevent the shift fork shaft snap ring from flying off.



b.
C288247

Remove the bolt from the No. 1 gear shift fork.


c.
C288248

Remove the No. 1 gear shift fork shaft from the intermediate plate.


d.
C288249

Remove the No. 1 gear shift fork from the reverse gear.


e.
C315166

Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.


Hide 33241 25.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C272920

Using a 5 mm pin punch and hammer, tap out the shift fork set slotted spring pin from the No. 3 gear shift fork shaft.


b.
C288250

Using 2 screwdrivers and a hammer, tap off the shift fork shaft snap ring from the No. 3 gear shift fork shaft.

NOTICE:

Use a cloth to prevent the shift fork shaft snap ring from flying off.



c.
C289009

Using a magnet hand, remove the No. 1 shift interlock roller from the reverse shift fork.


d.
C272922

Remove the No. 3 gear shift fork and No. 3 gear shift fork shaft from the intermediate plate.


Hide 33211 26.REMOVE REVERSE SHIFT FORK

a.
C290803

Remove the reverse shift fork from the reverse shift arm.


Hide 33228 27.REMOVE REVERSE SHIFT ARM BRACKET

a.
C291033

Remove the torsion spring from the reverse shift arm bracket.


b.
C291034

Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.


c.
C291035

Using a screwdriver, remove the snap ring from the reverse shift arm bracket.


d.
C291036

Remove the reverse shift arm from the reverse shift arm bracket.


Hide 33321A 28.REMOVE OUTPUT SHAFT REAR BEARING

a.
C315167

Using 2 screwdrivers and a hammer, tap off the shaft snap ring from the output shaft.


b.
C295008C01
2.302,0.667 2.563,0.406 2.563,0.406 2.792,0.406 false 0.208,1.021 0.521,1.219 0.313,0.198 10 false *a 2.646,1.573 2.958,1.771 0.313,0.198 10 false *b 2.896,0.323 3.208,0.521 0.313,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


Hide 29.INSPECT COUNTERSHAFT 5TH GEAR THRUST CLEARANCE

Hide 30.INSPECT COUNTERSHAFT 5TH GEAR RADIAL CLEARANCE

Hide 33421R 31.REMOVE COUNTER SHAFT REAR SNAP RING

a.
C272923

Using 2 screwdrivers and a hammer, tap off the counter shaft rear snap ring from the countershaft 5th gear.


Hide 33395 32.REMOVE NO. 3 TRANSMISSION HUB SLEEVE

a.
C282116

Remove the No. 3 transmission hub sleeve from the countershaft 5th gear.


Hide 33428 33.REMOVE COUNTERSHAFT 5TH GEAR

a.
C238818N01
0.708,1.417 0.469,1.802 true 0.302,1.854 0.625,2.063 0.323,0.208 10 false SST

Using SST, remove the countershaft 5th gear together with the 2 No. 3 synchromesh shifting keys, No. 3 synchromesh shifting key spring, No. 3 synchronizer ring and No. 5 gear spline piece from the counter gear.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04021, 09957-04010, 09958-04011)


Hide 33318 34.REMOVE NO. 5 GEAR SPLINE PIECE

a.
C250776C02
0.875,0.313 1.281,0.313 false 0.917,0.896 1.281,0.896 false 0.781,1.708 1.167,1.708 false 0.667,0.25 0.865,0.427 0.198,0.177 10 false *1 0.729,0.823 0.917,1.01 0.188,0.188 10 false *2 0.594,1.635 0.781,1.823 0.188,0.188 10 false *3
*1 No. 5 Gear Spline Piece
*2 No. 3 Synchronizer Ring
*3 Countershaft 5th Gear


Remove the No. 5 gear spline piece from the countershaft 5th gear.


Hide 33384A 35.REMOVE NO. 3 SYNCHRONIZER RING

a.

Remove the No. 3 synchronizer ring from the countershaft 5th gear.


Hide 33428B 36.REMOVE COUNTER 5TH GEAR BEARING

a.
C315168

Remove the counter 5th gear bearing from the countershaft 5th gear.


Hide 33394B 37.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY

a.
C247403

Using a snap ring expander, remove the shaft snap ring.


b.
C250077C02
2.865,1.375 2.865,0.958 false 2.167,1.646 2.167,1.229 false 1.156,1.917 1.156,1.646 false 2.781,1.406 2.99,1.615 0.208,0.208 10 false *1 2.094,1.667 2.281,1.875 0.188,0.208 10 false *2 1.073,1.938 1.271,2.125 0.198,0.188 10 false *3
*1 No. 3 Synchromesh Shifting Key Spring
*2 No. 3 Synchromesh Shifting Key
*3 Countershaft 5th Gear


Remove the No. 3 synchromesh shifting key spring and 2 No. 3 synchromesh shifting keys from the countershaft 5th gear.


Hide 33349 38.REMOVE 5TH GEAR THRUST WASHER

a.
C272927

Remove the 5th gear thrust washer from the counter gear.


Hide 33349C 39.REMOVE 5TH GEAR THRUST WASHER PIN

a.
C272929

Remove the 5th gear thrust washer pin from the counter gear.


Hide 33151 40.REMOVE OUTPUT SHAFT REAR BEARING RETAINER

a.
C315169

Remove the 4 bolts and output shaft rear bearing retainer from the intermediate plate.


Hide 33402 41.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C315170

Pull out the reverse idler gear shaft and reverse idler gear sub-assembly from the intermediate plate.


Hide 33411P 42.REMOVE COUNTER SHAFT REAR BEARING

a.
C272931

Using a snap ring expander, remove the snap ring.


b.
C272933N03
2.928,0.824 3.243,0.972 0.316,0.149 10 SST 2.876,0.909 2.802,0.909 2.802,0.909 2.61,1.101 false

Using SST, remove the counter shaft rear bearing from the intermediate plate.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

HINT:

Remove the counter shaft rear bearing while tapping the tip of the counter gear so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.



Hide 33421 43.REMOVE COUNTER GEAR

a.
C315171

Remove the counter gear from the intermediate plate.


Hide 33311 44.REMOVE INPUT SHAFT

a.
C315172

Remove the input shaft and No. 2 synchronizer ring from the output shaft.

NOTICE:

Do not drop the input shaft bearing and No. 2 synchronizer ring.



Hide 33321B 46.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C315173

Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft.


Hide 33321 47.REMOVE OUTPUT SHAFT

a.
C272539

Using a plastic-faced hammer, remove the output shaft by tapping the intermediate plate.


Hide 48.REMOVE STRAIGHT PIN

NOTICE:

If a straight pin is deformed or its threads are damaged, replace it.


Hide 49.REMOVE RING PIN

NOTICE:

If a ring pin is deformed or its threads are damaged, replace it.


Hide 33395 51.INSPECT NO. 3 TRANSMISSION HUB SLEEVE

Hide 33402 53.INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY