Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front air conditioning unit removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DRAIN ENGINE COOLANT (for Automatic Air Conditioning System, Manual Air Conditioning System)
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE COOLING>COOLANT>REPLACEMENT
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV COOLING>COOLANT>REPLACEMENT
for 2KD-FTV:
Click hereEngine / Hybrid System>2KD-FTV COOLING>COOLANT>REPLACEMENT
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV COOLING>COOLANT>REPLACEMENT
for 2GD-FTV:
Click hereEngine / Hybrid System>2GD-FTV COOLING>COOLANT>REPLACEMENT
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE COOLING>COOLANT>REPLACEMENT
for 5L-E:
Click hereEngine / Hybrid System>5L-E COOLING>COOLANT>REPLACEMENT
88710E
3.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for 1GD-FTV, 2GD-FTV)
Remove the bolt and disconnect the air conditioner tube and accessory assembly.
Remove the 2 O-rings from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88707
4.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (except 1GD-FTV, 2GD-FTV)
|
Remove in this Direction |
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88710E
5.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV)
Disconnect the air conditioner tube and accessory assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88710E
6.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV, w/ Sub-cool Accelerator)
|
Remove in this Direction |
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the air conditioner tube and accessory assembly.
Remove the 2 O-rings from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
7.DISCONNECT HEATER WATER OUTLET HOSE (for Automatic Air Conditioning System, Manual Air Conditioning System)
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.
Do not apply excessive force to the heater water outlet hose.
Prepare a drain pan or cloth in case the coolant leaks.
8.DISCONNECT HEATER WATER INLET HOSE (for Automatic Air Conditioning System, Manual Air Conditioning System)
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.
Do not apply excessive force to the heater water inlet hose.
Prepare a drain pan or cloth in case the coolant leaks.
87128
9.REMOVE HEATER GROMMET (for Automatic Air Conditioning System, Manual Air Conditioning System)
Detach the claw and remove the heater grommet.
10.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
11.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
55303B
12.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
87211A
13.REMOVE NO. 2 AIR DUCT
Remove the bolt.
Detach the claw and remove the No. 2 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
87211
14.REMOVE NO. 1 AIR DUCT
Detach the claw and remove the No. 1 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
15.REMOVE STEERING COLUMN ASSEMBLY
67914B
16.REMOVE FRONT DOOR SCUFF PLATE LH
62112
17.REMOVE COWL SIDE TRIM BOARD LH
67913B
18.REMOVE FRONT DOOR SCUFF PLATE RH
62111C
19.REMOVE COWL SIDE TRIM BOARD RH
67918E
20.REMOVE REAR DOOR SCUFF PLATE LH
67917C
21.REMOVE REAR DOOR SCUFF PLATE RH
62414A
22.REMOVE LOWER CENTER PILLAR GARNISH LH
62413A
23.REMOVE LOWER CENTER PILLAR GARNISH RH
24.REMOVE FRONT FLOOR CARPET ASSEMBLY
for RHD:
Remove the 5 clips.
|
Fastener |
|
Remove in this Direction |
for LHD:
Remove the 6 clips.
|
Fastener |
|
Remove in this Direction |
Detach each fastener.
Detach the guide and fold back the front floor carpet assembly as shown in the illustration.
55395C
25.REMOVE NO. 1 INSTRUMENT PANEL INNER BRACKET COVER LH (for LHD)
Remove the 3 clips and No. 1 instrument panel inner bracket cover LH
55215D
26.REMOVE NO. 3 DASH PANEL INSULATOR PAD
|
Remove in this Direction |
Remove the No. 3 dash panel insulator pad as shown in the illustration.
55214C
27.REMOVE NO. 2 DASH PANEL INSULATOR PAD
|
Remove in this Direction |
Remove the No. 2 dash panel insulator pad as shown in the illustration.
87216B
28.REMOVE NO. 4 REAR AIR DUCT (w/ Rear Foot Duct)
Detach the claw and remove the No. 4 rear air duct.
87216A
29.REMOVE NO. 5 REAR AIR DUCT (w/ Rear Foot Duct)
Detach the claw and remove the No. 5 rear air duct.
87213
30.REMOVE NO. 2 REAR AIR DUCT (w/ Rear Foot Duct)
Detach the claw and remove the No. 2 rear air duct.
87212G
31.REMOVE NO. 3 REAR AIR DUCT (w/ Rear Foot Duct)
Detach the claw and remove the No. 3 rear air duct.
87212
32.REMOVE NO. 1 REAR AIR DUCT (w/ Rear Foot Duct)
Remove the 2 clips and remove the No. 1 rear air duct.
55306A
33.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Detach the clamp.
Remove the nut, bolt, 4 screws and No. 1 instrument panel brace sub-assembly.
55307C
34.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Remove the nut, bolt, 3 screws and No. 2 instrument panel brace sub-assembly.
82141
35.DISCONNECT INSTRUMENT PANEL WIRE
for Automatic Air Conditioning System:
Disconnect the connector.
Detach the clamp.
for Manual Air Conditioning System:
Disconnect the connector.
Detach the clamp.
Remove each bolt and each ground wire.
| *A | for Manual Air Conditioning System | *B | for Automatic Air Conditioning System |
| *C | w/ PTC Heater | - | - |
| *1 | Ground Wire | - | - |
Disconnect each connector and detach each clamp.
Remove each bolt, nut and screw, and then disconnect the instrument panel wire.
55330B
36.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When removing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
| *A | for Driver Side |
|
Protective Tape |
Put protective tape around the hole plug.
Using a screwdriver with its tip wrapped with protective tape, remove the 2 hole plugs.
for Automatic Transmission:
Remove the 11 bolts.
| *A | for Manual Transmission | - | - |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
for Manual Transmission:
Remove the 12 bolts.
55950G
37.REMOVE DEFROSTER NOZZLE ASSEMBLY
Detach the claw and remove the defroster nozzle assembly.
38.REMOVE AIR CONDITIONING UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Disconnect the drain cooler hose.
Remove the nut and air conditioning unit assembly and instrument panel reinforcement assembly.
87211B
39.REMOVE NO. 3 AIR DUCT
Detach the claw and remove the No. 3 air duct.