Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1KD-FTV, 2KD-FTV) › 2016.01–2016.08
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0234826 COMPRESSOR(for 1KD-FTV, 2KD-FTV) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1KD-FTV, 2KD-FTV)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
E320440

Type A:

When replacing the compressor assembly with magnet clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor assembly with magnet clutch before installation.

Standard:

(Oil capacity inside the new compressor assembly with magnet clutch: 200 to 215 cc (6.76 to 7.27 fl.oz)) - (Remaining oil amount in the removed compressor assembly with magnet clutch) = (Oil amount to be removed from the new compressor)


NOTICE:
·

If a new compressor assembly with magnet clutch is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor assembly with magnet clutch is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 8 or equivalent compressor oil. If any compressor oil other than ND-OIL 8 is used, compressor assembly with magnet clutch insulation performance may decrease, resulting in a leak of electric power.




b.
E336424

Type B:

When replacing the compressor assembly with magnet clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor assembly with magnet clutch before installation.

Standard:

(Oil capacity inside the new compressor assembly with magnet clutch: 180 to 195 cc (6.09 to 6.59 fl.oz)) - (Remaining oil amount in the removed compressor assembly with magnet clutch) = (Oil amount to be removed from the new compressor)


NOTICE:
·

If a new compressor assembly with magnet clutch is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor assembly with magnet clutch is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 8 or equivalent compressor oil. If any compressor oil other than ND-OIL 8 is used, compressor assembly with magnet clutch insulation performance may decrease, resulting in a leak of electric power.




Hide 2.INSTALL COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH

a.
E320429N01
1.667,0.854 1.917,1.052 0.25,0.198 10 true (1) 1.135,1.938 1.344,2.135 0.208,0.198 10 true (3) 0.49,0.75 0.698,0.958 0.208,0.208 10 true (4) 0.531,1.792 0.74,2 0.208,0.208 10 true (2)

for Type A:

Tighten the 4 bolts in the order shown in the illustration to install the compressor assembly with magnet clutch.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


b.
E336419N01
1.667,0.865 1.885,1.063 0.219,0.198 10 true (1) 0.521,1.771 0.74,1.969 0.219,0.198 10 true (2) 1.115,1.948 1.333,2.146 0.219,0.198 10 true (3) 0.5,0.74 0.719,0.938 0.219,0.198 10 true (4)

for Type B:

Tighten the 4 bolts in the order shown in the illustration to install the compressor assembly with magnet clutch.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


c.
E320428

for Type A:

i.

Connect the connector.


ii.

Attach the clamp.



d.
E336418

for Type B:

i.

Connect the connector.


ii.

Attach the clamp.



Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E320427

for Type A:

i.

Remove the vinyl tape from the suction hose sub-assembly and compressor assembly with magnet clutch.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with magnet clutch.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



iv.

Connect the suction hose sub-assembly to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.
E336417

for Type B:

i.

Remove the vinyl tape from the suction hose sub-assembly and compressor assembly with magnet clutch.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with magnet clutch.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



iv.

Connect the suction hose sub-assembly to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
E320426

for Type A:

i.

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and compressor assembly with magnet clutch.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with magnet clutch.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



iv.

Connect the No. 1 cooler refrigerant discharge hose to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.
E336416

for Type B:

i.

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and compressor assembly with magnet clutch.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with magnet clutch.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



iv.

Connect the No. 1 cooler refrigerant discharge hose to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 12601E 6.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

Hide 7. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT