Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _049378 1KD-FTV ENGINE CONTROL _0236318 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

HINT:

If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the engine coolant temperature is assumed to be 80°C (176°F).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0117 Engine Coolant Temperature Circuit Low Input Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0118 Engine Coolant Temperature Circuit High Input Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0115 Coolant Temp
P0117
P0118

HINT:
·

If DTC P0115, P0117 and/or P0118 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine / Data List / Coolant Temp.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



CONFIRMATION DRIVING PATTERN

P0115, P0117, P0118
DTC Detection Drive Pattern Ignition switch to ON for 0.5 seconds

WIRING DIAGRAM

A255058E69
0.313,2.115 2.667,2.417 2.354,0.302 10 false Engine Coolant Temperature Sensor 0.313,1.969 0.688,2.177 0.375,0.208 10 false C35 5.948,2.458 6.385,2.688 0.438,0.229 10 false ECM 5.448,0.74 5.906,0.906 0.458,0.167 10 false THW 5.458,1.333 5.677,1.5 0.219,0.167 10 false E2 5.896,0.229 6.167,0.396 0.271,0.167 10 false 5 V 6.104,0.656 6.271,0.823 0.167,0.167 10 false R 1.969,0.75 2.094,0.906 0.125,0.156 10 false 2 1.969,1.323 2.094,1.49 0.125,0.167 10 false 1 5.948,2.323 6.406,2.49 0.458,0.167 10 false C114 5.198,0.74 5.385,0.896 0.188,0.156 10 false 19 5.188,1.333 5.375,1.49 0.188,0.156 10 false 28

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 234 8

d.

Read the value.

OK:

70 to 90°C (158 to 194°F) with warm engine



Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
70 to 90°C (158 to 194°F) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.




A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A213406C38
0.74,3.5 1.156,3.719 0.417,0.219 0.26,2.771 0.573,2.969 0.313,0.198 10 false *a 0.667,0.333 0.979,0.531 0.313,0.198 10 false *1 2.531,0.313 2.844,0.51 0.313,0.198 10 false *2 2.406,1.25 2.896,1.5 0.49,0.25 10 false THW 2.417,1.698 2.76,1.938 0.344,0.24 10 false E2 0.833,3.531 1.292,3.719 0.458,0.188 10 false C35
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 234 8

f.

Read the value.

OK:

140°C (284°F) or higher



g.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C35-2 - C114-19 (THW) Always Below 1 Ω
C35-1 - C114-28 (E2) Always Below 1 Ω



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C03
2.469,1.063 2.917,1.323 0.448,0.26 10 false THW 2.479,1.51 2.813,1.708 0.333,0.198 10 false E2 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Engine Coolant Temperature Sensor
*2 ECM


Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

10.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch to ON for 1 second.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C35-2 or C114-19 (THW) - Body ground Always 10 kΩ or higher



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED