Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _049378 1KD-FTV ENGINE CONTROL _0236318 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  Pre-heating Control Circuit  


DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval for the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned to ON. The ECM then turns on the GLOW relay and permits the current to flow through the glow plug based on the ECM's calculated time of the ECM. The GLOW relay is then heated, and enhances fuel combustion with a cold engine.

This DTC will be set if the glow plug or the circuit is open.

A255090E07
0.104,0.042 2.01,0.229 1.906,0.188 10 false Glow System Wiring Diagram 0.073,0.385 0.885,0.573 0.813,0.188 10 false from Battery 1.583,0.563 2.104,0.729 0.521,0.167 10 false GLOW 3.156,0.948 3.677,1.115 0.521,0.167 10 false GLOW 1.073,1.781 1.792,1.969 0.719,0.188 10 false Glow Plug 5.865,1.823 6.24,1.99 0.375,0.167 10 false ECM 5.146,0.396 5.594,0.563 0.448,0.167 10 false GREL 2.896,0.521 3.021,0.688 0.125,0.167 10 false 2 2.896,1.406 3.021,1.573 0.125,0.167 10 false 1 2.458,0.521 2.583,0.688 0.125,0.167 10 false 5 2.448,1.396 2.573,1.573 0.125,0.177 10 false 3

HINT:
·

These troubleshooting procedures are for the following conditions: 1) difficulty starting the engine in cold weather, and 2) difficulty driving the vehicle or vehicle malfunctions in cold weather immediately after engine is started.

·

After the engine is started, the ECM performs an "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.



A303110E01
0.125,0.063 1.469,0.302 1.344,0.24 10 false After-glow System 1.5,0.292 2.479,0.708 0.979,0.417 10 false After-glow Time (Second) 2.51,0.573 2.792,0.781 0.281,0.208 10 false 120 2.656,1.271 2.802,1.448 0.146,0.177 10 false 1 2.708,1.458 2.854,1.635 0.146,0.177 10 false 0 3.135,1.458 3.333,1.667 0.198,0.208 10 false 30 4.094,1.458 4.292,1.667 0.198,0.208 10 false 40 4.708,1.406 4.906,1.615 0.198,0.208 10 false °C 4.719,1.552 5.063,1.792 0.344,0.24 10 false (°F) 4.031,1.594 4.427,1.854 0.396,0.26 10 false (104) 3.104,1.594 3.396,1.844 0.292,0.25 10 false (86) 2.792,1.844 4.75,2.115 1.958,0.271 10 false Engine Coolant Temperature 1.271,2.552 2.292,2.771 1.021,0.219 10 false Ignition Switch 1.521,3.333 2.229,3.552 0.708,0.219 10 false Glow Plug 1.323,4.135 2.26,4.344 0.938,0.208 10 false Engine Speed 2.427,2.469 2.729,2.698 0.302,0.229 10 false OFF 2.448,3.26 2.75,3.49 0.302,0.229 10 false OFF 4.396,2.083 4.698,2.313 0.302,0.229 10 false ON 4.438,2.865 4.74,3.094 0.302,0.229 10 false ON 5.854,3.26 6.156,3.49 0.302,0.229 10 false OFF 4.229,4.177 5.198,4.385 0.969,0.208 10 false After-glow Time 2.813,4.563 3.854,4.802 1.042,0.24 10 false Starting Engine

WIRING DIAGRAM

A379321E01
1.948,0.833 2.719,1.031 0.771,0.198 10 false EFI-B 1.938,1.656 2.708,1.854 0.771,0.198 10 false GLOW 0.948,2.427 1.719,2.625 0.771,0.198 10 false FL MAIN 3.167,4.24 3.938,4.438 0.771,0.198 10 false Glow Plug 4.51,2.156 5.281,2.354 0.771,0.198 10 false GLOW 3.177,4.063 3.948,4.26 0.771,0.198 10 false C111 1.115,3.844 1.885,4.042 0.771,0.198 10 false Battery 3.531,1.74 3.698,1.917 0.167,0.177 10 false 5 3.521,2.542 3.688,2.719 0.167,0.177 10 false 3 4.26,2.552 4.427,2.729 0.167,0.177 10 false 1 4.26,1.74 4.427,1.917 0.167,0.177 10 false 2 5.354,0.677 5.813,0.865 0.458,0.188 10 false G140 5.344,1.479 5.802,1.667 0.458,0.188 10 false G141 5.354,3.615 5.813,3.802 0.458,0.188 10 false C115 5.802,3.615 6.26,3.802 0.458,0.188 10 false E1 5.458,3.417 5.917,3.604 0.458,0.188 10 false 7 5.802,1.49 6.26,1.677 0.458,0.188 10 false GREL 5.417,1.292 5.875,1.479 0.458,0.188 10 false 15 5.813,0.688 6.271,0.875 0.458,0.188 10 false BATT 5.469,0.49 5.927,0.677 0.458,0.188 10 false 2 6.083,4.385 6.542,4.573 0.458,0.188 10 false ECM 3.552,3.021 3.719,3.198 0.167,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.INSPECT GLOW RELAY
a.

Inspect the glow plug relay (GLOW).

Click hereEngine / Hybrid System>1KD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

REPLACE GLOW RELAY

2.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

3.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)

NG

REPLACE GLOW PLUG ASSEMBLY

3.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
a.

Check the glow plug installation.

OK:

Glow plugs are installed securely.



Torque:

13 N*m{ 130 kgf*cm , 10 ft.*lbf }


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW RELAY - ECM AND BODY GROUND)

NG

TIGHTEN GLOW PLUG

4.CHECK HARNESS AND CONNECTOR (GLOW RELAY - ECM AND BODY GROUND)
a.

Disconnect the ECM connector.


b.

Remove the GLOW relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-15 (GREL) - GLOW relay (2) Always Below 1 Ω
GLOW relay (1) - Body ground Always Below 1 Ω
G141-15 (GREL) or GLOW relay (2) - Body ground Always 10 kΩ or higher



d.

Reinstall the GLOW relay.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GLOW RELAY - GLOW PLUG AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GLOW RELAY - GLOW PLUG AND BATTERY)
a.

Remove the GLOW relay from the engine room relay block and junction block assembly.


b.

Disconnect the glow plug connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GLOW relay (3) - C111-1 Always Below 1 Ω
GLOW relay (5) - Positive (+) battery terminal cable Always Below 1 Ω
GLOW relay (3) or C111-1 - Body ground Always Below 1 Ω



d.

Reinstall the GLOW relay.


e.

Reconnect the glow plug connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM (BATT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (BATT VOLTAGE)
a.
A080463C89
1.219,0.323 1.656,0.563 0.438,0.24 1.938,0.323 2.385,0.563 0.448,0.24 1.156,0.802 0.896,1.552 false 2.271,0.802 2.448,1.552 false 0.115,0.094 0.333,0.271 0.219,0.177 10 false *a 0.771,1.583 1.219,1.781 0.448,0.198 10 false 7 (E1) 2.219,1.583 2.917,1.781 0.698,0.198 10 false 2 (BATT) 1.292,0.365 1.635,0.542 0.344,0.177 10 false C115 1.99,0.365 2.375,0.552 0.385,0.188 10 false G140
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G140-2 (BATT) - C115-7 (E1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK ECM (GREL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ECM (GREL VOLTAGE)
a.
A080463C90
1.24,0.167 1.688,0.427 0.448,0.26 2.479,0.167 2.906,0.427 0.427,0.26 1.177,0.792 0.906,1.552 true 2.635,0.875 2.49,1.531 true 1.302,0.219 1.698,0.417 0.396,0.198 10 false C115 2.542,0.219 2.948,0.406 0.406,0.188 10 false G141 0.667,1.573 1.115,1.771 0.448,0.198 10 false 7 (E1) 2.219,1.573 2.948,1.771 0.729,0.198 10 false 15 (GREL) 0.094,0.073 0.271,0.271 0.177,0.198 10 false *a
*a Component with harness connected
(ECM)


Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-15 (GREL) - C115-7 (E1) Engine coolant
temperature 40°C (104°F) or less
11 to 14 V



Result:
Proceed to
OK
NG



OK

NG