The Intake Air Temperature (IAT) sensor, mounted on the air cleaner hose, monitors the IAT. The IAT sensor has a thermistor that varies its resistance depending on the temperature of the intake air. When the air temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance decreases. The variations in resistance are communicated to the ECM as changes in voltage (see Fig. 1).
The IAT sensor is connected to the ECM (see below). The 5 V power source voltage in the ECM is applied to the IAT sensor from terminal THA via resistor R.
The resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes in accordance with changes in the IAT, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve the driveability during cold engine operation.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0110 | Intake Air Temperature Circuit | Open or short in IAT sensor circuit for 0.5 seconds (1 trip detection logic) | ·
Open or short in IAT sensor circuit ·
IAT sensor ·
ECM |
- | DTC stored |
| P0112 | Intake Air Temperature Circuit Low Input | Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic) | ·
Open or short in IAT sensor circuit ·
IAT sensor ·
ECM |
- | DTC stored |
| P0113 | Intake Air Temperature Circuit High Input | Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic) | ·
Open or short in IAT sensor circuit ·
IAT sensor ·
ECM |
- | DTC stored |
When DTC P0110, P0112 or P0113 is detected, check the intake air temperature by entering the following menus on the GTS: Powertrain / Engine / Data List / Intake Air.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| DTC Detection Drive Pattern | Ignition switch to ON for 0.5 seconds |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value.
Same as actual intake air temperature
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as actual intake air temperature) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
A
B
C
| *1 | Intake Air Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Intake Air Temperature Sensor) |
Disconnect the A54 intake air temperature sensor connector.
Connect terminals 1 and 2 of the intake air temperature sensor wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS ON.
Enter the following menus: Powertrain / Engine / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Enter the following menus: Powertrain / Engine / Data List / Intake Air.
Read the values.
140°C (284°F) or more
Reconnect the intake air temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (w/o mass air flow meter).
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A75-2 (THA) - C114-31 (THA) | Always | Below 1 Ω |
| A75-1 (E2) - C114-28 (E2) | Always | Below 1 Ω |
Reconnect the intake air temperature sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Intake Air Temperature Sensor |
| *2 | ECM |
Disconnect the intake air temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value.
-40°C (-40°F)
Reconnect the intake air temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A75-2 (THA) or C114-31 (THA) - Body ground | Always | 10 kΩ or higher |
Reconnect the intake air temperature sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT