Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048930 2KD-FTV ENGINE CONTROL _0236329 ECD SYSTEM C

2KD-FTV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch to ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

P0504
DTC Detection Drive Pattern Depress and release brake pedal with ignition switch to ON

WIRING DIAGRAM

A379127E04
1.729,1.698 2.344,1.896 0.615,0.198 10 false G135 1.729,1.865 3.427,2.083 1.698,0.219 10 false Ignition Switch Assembly 1.771,1.219 2.385,1.417 0.615,0.198 10 false AM2 2.531,1.219 2.813,1.385 0.281,0.167 10 false IG2 0.615,1.479 1.75,1.885 1.135,0.406 10 false AM2 NO. 2 3.365,1.469 4.073,1.667 0.708,0.198 10 false IG2 NO. 3 3.438,2.542 4.146,2.74 0.708,0.198 10 false STOP 0.833,2.552 1.542,2.75 0.708,0.198 10 false ALT 0.458,3.094 1.167,3.292 0.708,0.198 10 false FL MAIN 0.604,3.823 1.271,4.052 0.667,0.229 10 false Battery 5.104,2.396 5.438,2.583 0.333,0.188 10 false L 4.427,3.365 5.552,3.75 1.125,0.385 10 false Stop Light Switch Assembly 4.438,3.177 4.771,3.365 0.333,0.188 10 false A64 4.469,2.396 4.802,2.583 0.333,0.188 10 false B 4.479,1.313 4.813,1.5 0.333,0.188 10 false B 5.094,1.313 5.427,1.5 0.333,0.188 10 false L 4.875,2.74 5.208,2.927 0.333,0.188 10 false GND 5.969,1.198 6.302,1.385 0.333,0.188 10 false ST1- 5.979,2.292 6.313,2.479 0.333,0.188 10 false STP 4.281,1.198 4.615,1.385 0.333,0.188 10 false 6 5.281,2.281 5.615,2.469 0.333,0.188 10 false 3 5.281,1.198 5.615,1.385 0.333,0.188 10 false 5 4.302,2.271 4.635,2.458 0.333,0.188 10 false 7 5.271,2.635 5.604,2.823 0.333,0.188 10 false 2 5.708,2.281 6.042,2.469 0.333,0.188 10 false 15 5.708,1.208 6.042,1.396 0.333,0.188 10 false 14 6.24,3.365 6.708,3.552 0.469,0.188 10 false G140 6.25,3.542 6.583,3.729 0.333,0.188 10 false ECM 2.854,1.208 3.188,1.396 0.333,0.188 10 false 3 1.594,1.198 1.927,1.385 0.333,0.188 10 false 4

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)
a.
E270270C09
0.208,1.073 0.656,1.375 0.448,0.302 2.042,1.208 1.479,1.823 true 2.375,1.188 2.792,1.854 true 0.302,1.146 0.76,1.344 0.458,0.198 10 false A64 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.406,1.865 1.563,2.063 0.156,0.198 10 false B 2.781,1.896 2.938,2.094 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the igntion switch to ON


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-6 (B) - Body ground Ignition switch ON 11 to 14 V
A64-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY,INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A303106C16
1.938,2.531 2.354,2.792 0.417,0.26 1.552,3.938 1.927,3.177 true 2.333,3.906 1.979,3.177 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.771,0.083 2.083,0.281 0.313,0.198 10 false *b 0.25,2.219 0.563,2.417 0.313,0.198 10 false *c 1.979,2.573 2.552,2.771 0.573,0.198 10 false G140 1.292,3.948 1.896,4.198 0.604,0.25 10 false 15 (STP) 2.271,3.948 2.896,4.198 0.625,0.25 10 false 14 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G140-14 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
G140-15 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-3 (L) - G140-15 (STP) Always Below 1 Ω
A64-5 (L) - G140-14 (ST1-) Always Below 1 Ω
A64-3 (L) or G140-15 (STP) - Body ground and other terminals Always 10 kΩ or higher
A64-5 (L) or G140-14 (ST1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR