Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048930 2KD-FTV ENGINE CONTROL _0236329 ECD SYSTEM C

2KD-FTV ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

Starter relay circuit

·

Ignition switch

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

P0617
DTC Detection Drive Pattern Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

A355839E04
0.563,4.031 1.615,4.25 1.052,0.219 10 false FL MAIN 3.0W 1.292,2.906 2,3.146 0.708,0.24 10 false ST NO. 1 0.552,2.104 1.26,2.344 0.708,0.24 10 false J/B-B 0.563,1.427 1.615,1.646 1.052,0.219 10 false AM2 NO. 2 0.719,5.875 1.26,6.104 0.542,0.229 10 false Battery 2.229,5.729 2.771,5.958 0.542,0.229 10 false Starter 1.635,1.24 2.094,1.438 0.458,0.198 10 false G135 1.667,1.396 2.719,1.615 1.052,0.219 10 false Ignition Switch 1.667,0.979 2.042,1.177 0.375,0.198 10 false AM2 2.188,0.979 2.469,1.177 0.281,0.198 10 false ST2 1.479,0.729 1.76,0.927 0.281,0.198 10 false 4 2.531,0.729 2.813,0.927 0.281,0.198 10 false 2 3.083,1.01 4.135,1.229 1.052,0.219 10 false STA/WIPER-S 3.396,3.333 4.104,3.573 0.708,0.24 10 false ST NO. 1 3.167,2.927 3.448,3.125 0.281,0.198 10 false 2 3.167,3.74 3.448,3.938 0.281,0.198 10 false 1 2.583,2.927 2.865,3.125 0.281,0.198 10 false 5 2.573,3.75 2.854,3.948 0.281,0.198 10 false 3 1.583,5.271 1.865,5.469 0.281,0.198 10 false D3 2.583,4.427 2.865,4.625 0.281,0.198 10 false 1 1.604,5.063 1.885,5.26 0.281,0.198 10 false 1 2.583,4.625 2.917,4.823 0.333,0.198 10 false C26 4.75,1.729 6.052,1.927 1.302,0.198 10 false Clutch Start Switch 4.76,1.552 5.042,1.75 0.281,0.198 10 false B2 6.292,3.354 6.75,3.573 0.458,0.219 10 false G141 6.156,2.719 6.615,2.938 0.458,0.219 10 false STA 5.917,2.604 6.198,2.802 0.281,0.198 10 false 7 4.365,1.333 4.646,1.531 0.281,0.198 10 false 2 4.365,2.115 4.646,2.313 0.281,0.198 10 false 1 6.302,3.531 6.76,3.75 0.458,0.219 10 false ECM 1.875,5.177 2.156,5.375 0.281,0.198 10 false B 2.771,4.833 3.229,5.052 0.458,0.219 10 false ST

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF A
ON B




A

B

2.INSPECT CLUTCH START SWITCH
2.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

7.REPLACE CLUTCH START SWITCH
3.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2KD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

6.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B



A

B

END

6.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2KD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
7.REPLACE CLUTCH START SWITCH
a.

Replace the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)