Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048930 2KD-FTV ENGINE CONTROL _0236329 ECD SYSTEM J

2KD-FTV ENGINE CONTROL  ECD SYSTEM  Black Smoke Emitted  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List MAP

Glow System
Main fault Open circuit, glow plug relay fault
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug

Engine
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Diesel Injection

Fuel Supply Pump
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure, Target Pump SCV Current
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the Common Rail Pressureure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage, increase in fuel injection volume
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



HINT:
·

When the sliding resistance of the internal parts of the injector assemblies (i.e. armature shaft, command piston and plunger) has increased due to internal contamination, injection quantity will increase at high common rail pressure due to a delay in injector assembly closure.

·

When black smoke occurs due to contamination of the injector assemblies, there are usually other symptoms, such as engine knocking noise at cold idling, rough idling, difficulty starting, etc. which are also present when the common rail pressure is low.



Injector Driver
Main fault Circuit fault: The injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Common Rail Pressure and Common Rail Pres Sens 2 follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Common Rail Pressure or Common Rail Pres Sens 2 decreases to a value less than Target Common Rail Pressure).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position

100%: Fully open

0%: Fully closed

·

When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Black Smoke


·

Engine Speed

·

MAP

·

Intake Air

·

Coolant Temp

·

Engine Speed of Cyl #1 (to #4)

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Common Rail Pressure

·

Common Rail Pressure

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing a Fuel Supply Pump, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


Explanation of Symptom


Black Smoke The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with a larger air fuel ratio across the entire operating range. An insufficient quantity of air results in imperfect combustion and increased particulate (soot) emissions.
When the accelerator pedal is depressed, a large amount of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited.
Black smoke is emitted when either 1) a lack of oxygen is present during combustion, or 2) Too much fuel is injected for a given intake air mass and the air fuel ratio becomes temporarily rich.


PROCEDURE

1.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read pending DTCs.

Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B




A

2.CHECK FOR BLACK SMOKE

B

2.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times or more.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

After repeating 10 times or more, black smoke stops being emitted.


HINT:

If the procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.



Result:
Proceed to
OK
NG



OK

3.RECOVERY TO NORMAL

NG

4.CHECK AIR INTAKE SYSTEM
3.RECOVERY TO NORMAL
HINT:

If the racing procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.


Result:
Proceed to
NEXT



NEXT

END

4.CHECK AIR INTAKE SYSTEM
a.

Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Make sure that the air cleaner is not clogged and the intake and exhaust system hoses are not disconnected.

·

When the vacuum hoses are disconnected (the swirl control valve is always fully open) or the valve is stuck open, smoke may increase without feeling a lack of power (visually check the operation of the swirl control valve when starting the engine).

·

Check that there are no disconnected, pinched or leaking hoses or pipes.

·

Check that there are no modifications made by the user.



OK:

No leakage or blockage.



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

5.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
a.

Check the wire harness and connector connections of common rail system components.

OK:

The wire harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

6.CHECK INJECTOR COMPENSATION CODE

NG

31.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation codes.

OK:

Compensation codes stored in the ECM match the compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

7.PERFORM PILOT QUANTITY LEARNING (DETAIL)

NG

16.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
7.PERFORM PILOT QUANTITY LEARNING (DETAIL)
a.

Perform the pilot quantity learning (detail).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

8.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)
8.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data.


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

9.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4)
9.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4)
a.

Check Injection Feedback Val # and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute.

Result:
Result Proceed to
Injection Volume is less than 10 mm3/st at 4000 rpm A
Injection Feedback Val for at least one cylinder is more than +3 mm3/st B
Except above C




A

10.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

11.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

18.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
10.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

14.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
11.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
50004 234 111 379,380,381,382

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

12.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

13.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
12.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>2KD-FTV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

13.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

13.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

14.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
14.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

15.BLEED AIR FROM FUEL SYSTEM
15.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

16.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
16.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

17.CHECK FOR BLACK SMOKE
17.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
NEXT



NEXT

END

18.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / MAP and Atmosphere Pressure.

Powertrain > Engine > Data List
Tester Display
Atmosphere Pressure
MAP
50003 234 7,4

d.

Compare MAP to Atmosphere Pressure when the ignition switch is ON (engine stopped).

HINT:
·

If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 10 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).



Result:
Result Proceed to
Atmosphere Pressure is different from actual atmospheric pressure A
MAP is different from actual atmospheric pressure B
MAP and Atmosphere Pressure have same value C




A

19.REPLACE ECM

B

20.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

C

21.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
19.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

34.CHECK FOR BLACK SMOKE
20.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR BLACK SMOKE
21.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Common Rail Pressure
50004 234 90 850,851

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E56
3.698,2.438 3.813,2.104 3.813,2.104 3.885,2.104 false 4.427,2.604 5.01,2.469 5.01,2.469 5.073,2.469 false 3.427,2.646 3.323,1.917 3.323,1.917 3.167,1.917 true 3.708,3.271 3.938,4.229 3.938,4.229 4.083,4.229 false 0.083,1.448 1.49,1.823 1.406,0.375 10 false Active Test Operation 0.167,0.615 1.604,0.938 1.438,0.323 10 false Engine Speed (rpm) 0.146,3.292 1.792,3.542 1.646,0.25 10 false Common Rail Pressure 3.927,2.01 6.052,2.271 2.125,0.26 10 false Target Common Rail Pressure 6.469,4.135 6.948,4.375 0.479,0.24 10 false Time 2.125,2.427 2.802,2.917 0.677,0.49 10 false Less than 10000 kPa 3,4.271 3.917,4.479 0.917,0.208 10 false 2 seconds 5.125,2.375 6.01,2.948 0.885,0.573 10 false Abnormal Common Rail Pressure 2.448,1.146 3.125,1.344 0.677,0.198 10 false Test Start 4.177,1.146 4.844,1.344 0.667,0.198 10 false Test Stop 5.625,1.146 6.302,1.344 0.677,0.198 10 false Test Start 2.104,1.833 3.219,2.365 1.115,0.531 10 false Normal Common Rail Pressure 1.646,0.302 2.021,0.469 0.375,0.167 10 false 2000 1.885,0.865 2.052,1.031 0.167,0.167 10 false 0 1.75,1.333 2.073,1.5 0.323,0.167 10 false ON 1.698,1.594 2.021,1.76 0.323,0.167 10 false OFF 4.146,4.135 6.302,4.552 2.156,0.417 10 false Pressure Discharge Valve Abnormal Common Rail Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Common Rail Pressure" is the actual fuel pressure.




Result:
Proceed to
OK
NG



OK

22.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

NG

26.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
22.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 234 8
OK:

Coolant Temp is the same as the ambient temperature.


HINT:

When the engine coolant temperature is low even though the engine has been fully warmed up, or when the engine coolant temperature is high even though the engine is cold, inspect the sensor.



Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (INTAKE AIR)

NG

24.CHECK AND REPLACE ENGINE COOLANT TEMPERATURE SENSOR
23.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 234 5
OK:

Intake Air is the same as the ambient temperature.



Result:
Proceed to
OK
NG



OK

34.CHECK FOR BLACK SMOKE

NG

25.CHECK AND REPLACE MALFUNCTIONING PARTS
24.CHECK AND REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

b.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

34.CHECK FOR BLACK SMOKE
25.CHECK AND REPLACE MALFUNCTIONING PARTS
a.

b.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

34.CHECK FOR BLACK SMOKE
26.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C127-1 - C114-2 (PCV+) Always Below 1 Ω
C127-2 - C114-1 (PCV-) Always Below 1 Ω
C127-1 or C114-2 (PCV+) - Body ground Always 10 kΩ or higher
C127-2 or C114-1 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

27.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP

NG

31.REPAIR OR REPLACE HARNESS OR CONNECTOR
27.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
a.

Disconnect the inlet hose from the fuel supply pump.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

OK:

Fuel is properly supplied to the fuel supply pump when the priming pump is operated.


HINT:
·

When there is a lack of fuel, the fuel pressure drops.

·

Inspect for fuel filter clogging (Check that the fuel filter is not clogged).




c.

Reconnect the inlet hose.


Result:
Proceed to
OK
NG



OK

28.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

32.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
28.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.BLEED AIR FROM FUEL SYSTEM
29.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

30.PERFORM FUEL SUPPLY PUMP INITIALIZATION
30.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform supply pump initialization.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR BLACK SMOKE
31.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR BLACK SMOKE
32.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
a.

Check and replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

33.BLEED AIR FROM FUEL SYSTEM
33.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR BLACK SMOKE
34.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

END

NG

35.BASIC INSPECTION
35.BASIC INSPECTION
a.

Check the fuel quality.


b.

Check the fuel for air.


c.

Check the fuel system for blockages.


d.

Check the air filter.


e.

Check the engine oil.


f.

Check the engine coolant.


g.

Check the engine idling speed and maximum engine speed.


h.

Check the vacuum pump.


Result:
Proceed to
NEXT



NEXT

END