While the engine is being cranked, current flows from terminal ST2 of the ignition switch to the clutch swich and also flows to terminal STA of the ECM (STA Signal).
Refer to DTC P0617 (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>P0617).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Read the value.
| Ignition Switch Condition | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block and Junction Block |
| *2 | ST NO. 1 Relay |
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 2 - Body ground | Engine cranking | 11 to 14 V |
The engine does not crank because the relay is not installed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>2KD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and Junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the clutch start switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B2-1 - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| G141-7 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the clutch start switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G135-2 (ST2) - B2-2 | Always | Below 1 Ω |
| G135-2 (ST2) or B2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2KD-FTV STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG