Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _041671 1GD-FTV ENGINE CONTROL _0236339 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0337  Crankshaft Position Sensor "A" Circuit Low Input  P0338  Crankshaft Position Sensor "A" Circuit High Input  


DESCRIPTION

Refer to DTC P0335.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>P0335

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0337 Crankshaft Position Sensor "A" Circuit Low Input Output voltage of crankshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored
P0338 Crankshaft Position Sensor "A" Circuit High Input Output voltage of crankshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored

HINT:

If DTC P0337 or P0338 is stored, the following symptoms may appear:

·

Difficulty starting

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




Reference: Inspection using an oscilloscope.

A340471E01
3.042,1.021 3.375,1.281 0.333,0.26 10 false GND 3.031,1.542 3.365,1.771 0.333,0.229 10 false GND 0.052,0.854 0.406,1.094 0.354,0.24 10 false G2 0.063,1.396 0.354,1.625 0.292,0.229 10 false NE 2.729,0.156 3.323,0.354 0.594,0.198 10 false 2 V/DIV. 1.292,1.833 2.5,2 1.208,0.167 10 false 20 msec./DIV.

The correct waveform is as shown.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0337 Engine switch on (IG) for 4 seconds or more
P0338

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Record any output DTC(s).

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

f.

Turn the engine switch off for 30 seconds or more.


g.

Disconnect the crankshaft position sensor connector.


h.

Turn the engine switch on (IG) for 4 seconds or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Check whether the DTC changes when the connector is disconnected and connected.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC does not change A
DTC changes B




A

2.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)

B

5.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)
a.
A368773C13
1.76,0.813 2.156,1.083 0.396,0.271 2.042,1.625 1.729,2.198 true 2.417,2.188 2.083,1.635 true 1.833,0.875 2.292,1.073 0.458,0.198 10 false C41 2.406,2.333 3.323,2.531 0.917,0.198 10 false 19 (NE-) 1.333,2.333 2.302,2.552 0.969,0.219 10 false 20 (VCNE) 0.167,0.198 0.625,0.396 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C41-20 (VCNE) - C41-19 (NE-) Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-1 (NE+) - C41-28 (NE+) Always Below 1 Ω
Z1-2 (NE-) - C41-19 (NE-) Always Below 1 Ω
Z1-1 (NE+) or C41-28 (NE+) - Body ground and other terminals Always 10 kΩ or higher
Z1-2 (NE-) or C41-19 (NE-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the crankshaft position sensor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the crankshaft position sensor connector.


b.
A368773C14
1.76,0.813 2.156,1.083 0.396,0.271 2.031,1.646 1.479,2.198 true 2.021,2.229 2.073,1.646 true 2.531,2.24 2.115,1.688 true 1.833,0.875 2.292,1.073 0.458,0.198 10 false C41 1.667,2.292 2.583,2.49 0.917,0.198 10 false 19 (NE-) 0.833,2.281 1.802,2.5 0.969,0.219 10 false 20 (VCNE) 2.438,2.292 3.219,2.49 0.781,0.198 10 false 28 (NE+) 0.135,0.135 0.594,0.333 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C41-20 (VCNE) - C41-28 (NE+) Engine switch off No short or open circuit
C41-28 (NE+) - C41-19 (NE-) Engine switch off No short or open circuit



c.

Reconnect the crankshaft position sensor connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE CRANKSHAFT POSITION SENSOR

NG

7.REPLACE ECM
5.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the engine switch off for 30 seconds or more.


f.

Turn the engine switch on (IG) for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END