Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P0101  Mass Air Flow Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0100.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>P0100

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0101 Mass Air Flow Circuit Range / Performance Problem After the engine is completely warmed up, while the accelerator pedal is released for 7 seconds or more and the vehicle is decelerating, the intake air volume is higher or lower than the threshold* (EGR valve fully closed and throttle valve is fully open).
(2 trip detection logic)
*: There is a threshold for a low air flow rate malfunction and high air flow rate malfunction. The threshold is different depending on the values of "Engine Speed", "MAP" and "Intake Air Temp (Turbo)".
·

Mass air flow meter sub-assembly

·

Intake air temperature sensor (turbo)

·

Manifold absolute pressure sensor

·

Electric EGR control valve assembly

·

ECM

·

Open or short in mass air flow meter sub-assembly circuit


Comes on DTC stored

HINT:
·

Low air flow rate malfunction: For example when vehicle deceleration if "MAF" is 10 gm/sec or less, low air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "MAP" is 110 kPa and "Intake Air Temp (Turbo)" is 35°C).

·

High air flow rate malfunction: For example when vehicle deceleration if "MAF" is 40 gm/sec or more, high air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "MAP" is 110 kPa and "Intake Air Temp (Turbo)" is 35°C).



Related Data List
DTC No. Data List
P0101
·

MAF

·

MAP

·

Engine Speed

·

Intake Air Temp (Turbo)

·

Target EGR Valve Pos

·

Actual EGR Valve Pos

·

EGR Close Lrn. Val.



HINT:

If DTC P0101 is stored, either of the following symptoms may appear:

1.

As the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased to match the target EGR.

·

Combustion noise worsens


2.

As the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased to match the target EGR:

·

Misfire

·

White smoke

·

Black smoke




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0101 After the engine is completely warmed up, perform the following procedure 3 times: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0101 and other DTCs are output A
P0101 is output B


HINT:

If codes other than P0101 are output, perform troubleshooting for those DTCs first.




A

B

2.CHECK FREEZE FRAME DATA (MAF AND ENGINE SPEED)
2.CHECK FREEZE FRAME DATA (MAF AND ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check the freeze frame data.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
·

Engine speed 1350 rpm or less

·

MAF 246.0 gm/sec or more


A
·

Engine speed 1350 rpm or more

·

MAF 0.03 gm/sec or less


Except above B




A

3.READ VALUE USING GTS (MAF AND ENGINE SPEED)

B

8.READ VALUE USING GTS (MAF AND ENGINE SPEED)
3.READ VALUE USING GTS (MAF AND ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Engine speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
50003 234 9,3

d.

Read the value.

Standard:
Engine speed MAF
Idling
·

2 to 17 gm/sec (EGR on)

·

13 to 20 gm/sec (EGR off)


3000 rpm
·

36 to 67 gm/sec (EGR on)

·

63 to 72 gm/sec (EGR off)





Result:
Proceed to
OK
NG



OK

4.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
4.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0101.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC P0101 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 (FG) - C39-33 (VG) Always Below 1 Ω
A29-2 (E2G) - C39-24 (EVG) Always Below 1 Ω
A29-1 (FG) or C39-33 (VG) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the mass air flow meter sub-assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.READ VALUE USING GTS (MAF AND ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Engine speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
50003 234 9,3

e.

Read the value.

Standard:
Engine speed MAF
Idling
·

2 to 17 gm/sec (EGR on)

·

13 to 20 gm/sec (EGR off)


3000 rpm
·

36 to 67 gm/sec (EGR on)

·

63 to 72 gm/sec (EGR off)





Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (MAP AND ATMOSPHERIC PRESSURE)

NG

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
9.READ VALUE USING GTS (MAP AND ATMOSPHERIC PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmospheric Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
MAP
50003 234 7,4

d.

Compare the values when the ignition switch is ON.

Standard:

Difference between "MAP" and "Atmosphere Pressure" is less than 8 kPa.


HINT:
·

If "MAP" and "Atmosphere Pressure" have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.




Result:
Proceed to
OK
NG



OK

10.CHECK INTAKE SYSTEM

NG

26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
10.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leakage.

Click hereEngine / Hybrid System>2GD-FTV INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leakage from intake system.


HINT:
·

Check for abnormal disconnection, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

Air leaks from the intake system can be checked by applying soapy water and revving the engine.

·

Check for any modifications in the intake system made by the user.




Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP [TURBO])

NG

25.REPAIR OR REPLACE INTAKE SYSTEM
11.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP [TURBO])
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
Intake Air Temp (Turbo)
50003 234 5,854
OK:

Intake Air is the same as Intake Air Temp (Turbo).



Result:
Proceed to
OK
NG



OK

12.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

23.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
12.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the EGR Step Position
50004 234 95

d.

When changing the Active Test continuously value to 1, 30, 60, 90, 60, 30 and 1%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / EGR Close Lrn. Val.

Powertrain > Engine and ECT > Data List
Tester Display
EGR Close Lrn. Val.
50003 234 348

f.

Read the values.

Standard:

0 to 1 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

16.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 (FG) - C39-33 (VG) Always Below 1 Ω
A29-2 (E2G) - C39-24 (EVG) Always Below 1 Ω
A29-1 (FG) or C39-33 (VG) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the mass air flow meter sub-assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

14.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
15.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0101.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC P0101 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

21.REPLACE ECM
16.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.




c.
A346511C01
0.865,2.458 1.115,2.708 0.25,0.25 2.115,4.344 2.26,4.344 2.26,4.344 2.604,3.854 true 2.594,3.229 2.75,2.531 2.75,2.531 2.885,2.531 true 0.667,3.469 0.688,2.583 0.688,2.583 0.792,2.583 true 0.938,2.49 1.094,2.688 0.156,0.198 10 false A 2.948,2.469 3.208,2.708 0.26,0.24 10 false *1 1.969,4.281 2.26,4.5 0.292,0.219 10 false *1 0.844,4.198 1.135,4.417 0.292,0.219 10 false *a 2.604,4.188 2.896,4.406 0.292,0.219 10 false *b
*1 Gap
*a OK
*b NG


Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

OK:

No light passes through (there is no gap between the valve and body).


HINT:

Light passes through part A shown in the illustration even if the valve is completely closed as there is an opening in the sealring of the valve, this is not a problem.


If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.


Result:
Proceed to
OK
NG



OK

17.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

22.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
17.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

18.CHECK DTC OUTPUT
18.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0101.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC P0101 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

21.REPLACE ECM
19.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the pending DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

21.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
23.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Inspect the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

17.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

24.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
24.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the intake system.


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED