Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

ST NO. 1 relay circuit

·

Ignition switch assembly

·

Park/Neutral position switch assembly

·

Clutch start switch

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

w/ Smart Entry and Start System, w/o Stop and Start System
A348895E07
6.479,3.063 6.844,3.26 0.365,0.198 10 false ECM 4.948,1.354 5.25,1.542 0.302,0.188 10 false C22 6.094,0.448 6.302,0.625 0.208,0.177 10 false 23 6.104,0.813 6.313,0.99 0.208,0.177 10 false 11 6.083,2.646 6.292,2.823 0.208,0.177 10 false 22 6.333,0.354 6.698,0.552 0.365,0.198 10 false NEO 6.333,0.719 6.708,0.906 0.375,0.188 10 false NSW 6.333,2.521 6.656,2.708 0.323,0.188 10 false STA 6.479,2.896 6.781,3.073 0.302,0.177 10 false G49 4.938,1.542 6.333,1.969 1.396,0.427 10 false Park/Neutral Position Switch Assembly*2 2.948,1.688 4.281,1.854 1.333,0.167 10 false Clutch Start Switch*1 2.969,1.521 3.219,1.698 0.25,0.177 10 false B2 4.656,1.031 4.792,1.208 0.135,0.177 10 false 4 4.656,1.26 4.792,1.438 0.135,0.177 10 false B 4.646,1.906 4.781,2.083 0.135,0.177 10 false L 4.656,2.146 4.792,2.323 0.135,0.177 10 false 5 2.656,1.021 2.792,1.198 0.135,0.177 10 false 2 2.656,2.167 2.792,2.344 0.135,0.177 10 false 1 0.917,0.344 1.208,0.521 0.292,0.177 10 false G16 0.927,0.698 1.219,0.875 0.292,0.177 10 false G17 0.927,2.521 1.219,2.698 0.292,0.177 10 false G17 1,0.156 1.135,0.333 0.135,0.177 10 false 6 0.969,0.531 1.156,0.708 0.188,0.177 10 false 16 1,2.323 1.188,2.5 0.188,0.177 10 false 37 0.594,0.333 0.833,0.5 0.24,0.167 10 false NE 0.448,0.688 0.844,0.865 0.396,0.177 10 false STAR 0.531,2.521 0.854,2.708 0.323,0.188 10 false STA 0.063,2.938 1.938,3.344 1.875,0.406 10 false Certification ECU (Smart Key ECU Assembly) 2.823,4.146 3.438,4.323 0.615,0.177 10 false ST NO. 1 2.677,4.531 2.813,4.708 0.135,0.177 10 false 1 2.667,3.76 2.802,3.938 0.135,0.177 10 false 2 2.063,3.771 2.198,3.948 0.135,0.177 10 false 5 2.052,4.542 2.188,4.719 0.135,0.177 10 false 3 2.063,5.208 2.354,5.385 0.292,0.177 10 false C26 2.385,5.208 2.521,5.385 0.135,0.177 10 false 1 2.052,5.438 2.302,5.604 0.25,0.167 10 false ST 1.583,6.177 2.708,6.354 1.125,0.177 10 false Starter Assembly 1.365,5.531 1.583,5.708 0.219,0.177 10 false D3 0.854,3.844 1.469,4.021 0.615,0.177 10 false ST NO. 1 0.417,4.656 1.375,4.854 0.958,0.198 10 false FL MAIN 1.406,5.313 1.542,5.49 0.135,0.177 10 false 1 1.667,5.542 1.802,5.719 0.135,0.177 10 false B 4.427,5.719 6.167,5.906 1.74,0.188 10 false *1: for Manual Transmission 4.417,6.167 6.604,6.396 2.188,0.229 10 false *2: for Automatic Transmission 0.521,5.969 1.021,6.156 0.5,0.188 10 false Battery

w/o Smart Entry and Start System
A360758E12
0.625,1.198 1.042,1.396 0.417,0.198 10 false G135 0.635,1.365 2.24,1.594 1.604,0.229 10 false Ignition Switch Assembly 0.542,0.667 0.854,0.865 0.313,0.198 10 false 4 1.823,0.667 2.135,0.865 0.313,0.198 10 false 2 0.74,0.667 1.115,0.844 0.375,0.177 10 false AM2 1.469,0.667 1.844,0.844 0.375,0.177 10 false ST2 2.948,1.375 3.26,1.573 0.313,0.198 10 false 2 2.927,2.458 3.24,2.656 0.313,0.198 10 false 4 4.052,2.458 4.365,2.656 0.313,0.198 10 false 5 4.042,1.375 4.354,1.573 0.313,0.198 10 false 1 2.219,2.823 2.635,3.021 0.417,0.198 10 false C22 3.115,1.833 3.427,2.031 0.313,0.198 10 false B2 2.229,3 4.885,3.24 2.656,0.24 10 false Park/Neutral Position Switch Assembly*2 3.104,2.01 4.708,2.24 1.604,0.229 10 false Clutch Start Switch*1 5.208,0.781 5.521,0.979 0.313,0.198 10 false G49 5.208,3.542 5.521,3.74 0.313,0.198 10 false G49 5.24,0.594 5.552,0.792 0.313,0.198 10 false 11 5.26,3.365 5.573,3.563 0.313,0.198 10 false 22 5.583,0.781 6.063,0.979 0.479,0.198 10 false NSW 5.583,3.552 6.063,3.75 0.479,0.198 10 false STA 1.604,5.958 3.208,6.188 1.604,0.229 10 false Starter Assembly 1.406,5.49 1.719,5.688 0.313,0.198 10 false D3 1.948,5.01 2.26,5.208 0.313,0.198 10 false C26 1.969,5.219 2.281,5.417 0.313,0.198 10 false ST 1.708,5.479 2.021,5.677 0.313,0.198 10 false B 2.115,4.802 2.427,5 0.313,0.198 10 false 1 1.427,5.292 1.74,5.49 0.313,0.198 10 false 1 2.677,4.594 2.99,4.792 0.313,0.198 10 false 1 2.688,3.813 3,4.01 0.313,0.198 10 false 2 1.938,3.813 2.25,4.01 0.313,0.198 10 false 5 1.927,4.594 2.24,4.792 0.313,0.198 10 false 3 2.844,4.198 3.5,4.406 0.656,0.208 10 false ST NO. 1 0.896,3.708 1.552,3.917 0.656,0.208 10 false ST NO. 1 0.448,4.552 1.51,4.771 1.063,0.219 10 false FL MAIN 3.0W 5.917,4.823 6.573,5.031 0.656,0.208 10 false ECM 0.521,5.885 1.177,6.094 0.656,0.208 10 false Battery 0.406,2.135 2.01,2.365 1.604,0.229 10 false STRG LOCK/AM2 NO. 1 3.25,5.396 5.906,5.635 2.656,0.24 10 false *1: for Manual Transmission 3.25,5.688 5.906,5.927 2.656,0.24 10 false *2: for Automatic Transmission 3.156,2.469 3.313,2.667 0.156,0.198 10 false B 3.854,2.479 4.01,2.677 0.156,0.198 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF A
ON w/ Smart Entry and Start System for automatic transmission B
for manual transmission C
w/o Smart Entry and Start System for automatic transmission D
for manual transmission E




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

6.INSPECT CLUTCH START SWITCH

D

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

E

13.INSPECT CLUTCH START SWITCH
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (park/neutral position switch assembly - ST NO. 1 relay - ECM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B



A

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)

B

END

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)

Result:
Proceed to
OK
NG



OK

NG

REPAIR SMART ENTRY AND START SYSTEM

6.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE CLUTCH START SWITCH

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

12.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
10.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER DTC OUTPUT RECURS
11.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

12.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER DTC OUTPUT RECURS
13.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

18.REPLACE CLUTCH START SWITCH
14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

15.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

17.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
15.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER DTC OUTPUT RECURS
16.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

17.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER DTC OUTPUT RECURS
18.REPLACE CLUTCH START SWITCH
a.

Replace the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER DTC OUTPUT RECURS