Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0627 Fuel Pump Control Circuit / Open Even though the CPU (command area inside the ECU) is outputting the pre-stroke control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
·

Open or short in pre-stroke control valve circuit

·

Fuel supply pump assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0627
·

Common Rail Pressure

·

Target Common Rail Pressure



HINT:
·

For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).

·

When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Common Rail Pressure.

Under a stable operating condition such as idling, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0627 Idling for 1 second or more

WIRING DIAGRAM

A348538E02
0.719,1.854 1.177,2.052 0.458,0.198 10 false X1 0.708,2.052 2.802,2.281 2.094,0.229 10 false Pre-stroke Control Valve 1.76,0.521 2.219,0.719 0.458,0.198 10 false +B 1.646,1.188 2.104,1.385 0.458,0.198 10 false PCV 5.677,0.646 6.313,0.844 0.635,0.198 10 false PCV+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false PCV- 5.979,1.813 6.438,2.01 0.458,0.198 10 false C39 5.99,1.99 6.448,2.188 0.458,0.198 10 false ECM 2.073,0.75 2.531,0.948 0.458,0.198 10 false 1 2.073,1.406 2.531,1.604 0.458,0.198 10 false 2 5.479,0.75 5.938,0.948 0.458,0.198 10 false 3 5.49,1.438 5.948,1.635 0.458,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Inspect the pre-stroke control valve.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

NG

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (+B) - C39-3 (PCV+) Always Below 1 Ω
X1-2 (PCV) - C39-4 (PCV-) Always Below 1 Ω
X1-1 (+B) or C39-3 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
X1-2 (PCV) or C39-4 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the pre-stroke control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
No DTC is output A
P0627 is output B




A

END

B

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED