Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P1271  Fuel Regulator Circuit (EDU Drive)  P1272  Fuel Pressure Regulator Circuit  


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail assembly by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail assembly. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
·

For more information on the pressure discharge valve and common rail system, refer to System Description (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).



A208468E07
3.719,2.781 3.49,2.781 false 3.667,3 3.479,3.135 3.479,3.135 3.396,3.135 false 3.896,2.427 4.083,2.229 4.083,2.229 4.188,2.229 false 0.052,0.052 4.219,0.313 4.167,0.26 10 false Pressure Discharge Valve Operation Due to Sudden Deceleration: 0.927,0.375 2.031,0.833 1.104,0.458 10 false Accelerator Pedal Opening Angle 0.469,1.385 2.115,1.604 1.646,0.219 10 false Pressure Discharge Valve 1.135,2.292 2.042,2.542 0.906,0.25 10 false Fuel Pressure 2.594,0.542 2.979,0.771 0.385,0.229 10 false Open 4.135,1.396 4.521,1.656 0.385,0.26 10 false Open 2.594,1.156 3.104,1.396 0.51,0.24 10 false Closed 4.135,0.719 4.656,0.958 0.521,0.24 10 false Closed 4.25,2.146 6.219,2.406 1.969,0.26 10 false w/o Pressure Discharge Valve 1.719,2.688 3.542,2.948 1.823,0.26 10 false w/ Pressure Discharge Valve 2.104,3.042 3.635,3.271 1.531,0.229 10 false Target Fuel Pressure 3.927,3.292 5.042,3.521 1.115,0.229 10 false Time Reduction 3.323,3.531 3.698,3.771 0.375,0.24 10 false Time

A362191E01
4.219,2.01 4.792,1.573 4.792,1.573 4.906,1.573 true 3.042,2.406 3.146,2.406 3.146,2.406 3.729,1.667 true 0.104,0.115 3.49,0.313 3.385,0.198 10 false Cross Section Diagram of Pressure Discharge Valve: 1.594,0.583 3.854,0.813 2.26,0.229 10 false Return to Fuel Tank (Low Pressure) 0.313,1.521 2.156,1.917 1.844,0.396 10 false From Common Rail Assembly (High Pressure) 2.667,2.313 3.115,2.521 0.448,0.208 10 false Valve 4.958,1.51 5.583,1.729 0.625,0.219 10 false Solenoid

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1271 Fuel Regulator Circuit (EDU Drive) When the condition below is met a certain number of times (0.5 seconds) (1 trip detection logic):
·

Open or short in pressure discharge valve circuit.


·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve (common rail assembly)


Comes on DTC stored
P1272 Fuel Pressure Regulator Circuit The fuel pressure does not decrease while the engine is running
(1 trip detection logic).
·

Open or short in pressure discharge valve circuit (P1271 is stored simultaneously)

·

Pressure discharge valve (common rail assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1271
·

Common Rail Pressure

·

Target Common Rail Pressure

·

Pressure Discharge Valve


P1272

HINT:
·

After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure.

·

P1271:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not output.

·

P1272:

After clearing the DTC, perform the following procedure 5 times, and then check that P1272 is not output: Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal.


Reference
Engine Speed Common Rail Pressure (kPa)
Idling Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure
3000 rpm (No engine load)

Results of Real-vehicle Check
Condition Common Rail Pressure (Idling) Common Rail Pressure (1 Second after Engine Stopped)
Pressure discharge valve normal 35000 kPa 500 kPa
Open in pressure discharge valve circuit 35000 kPa 30000 kPa


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1271 Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal
P1272 Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.

MONITOR DESCRIPTION

P1271 (Open or short in pressure discharge valve circuit):

This DTC is output when there is an open or short circuit in the pressure discharge valve circuit. When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the ignition switch is turned off.


P1272 (Pressure discharge valve stuck closed):

The pressure discharge valve opens when the common rail target fuel pressure decreases during deceleration, decreasing the fuel pressure in the common rail assembly. The ECM compares the speed that the fuel pressure decreases with the speed that the common rail target fuel pressure decreases. When the ECM determines that the decreasing rate of the fuel pressure is smaller than the common rail target fuel pressure, the ECM determines that the valve is stuck closed and outputs this DTC.

When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A348538E16
0.719,1.854 1.177,2.052 0.458,0.198 10 false Z3 0.708,2.052 2.802,2.281 2.094,0.229 10 false Pressure Discharge Valve 1.573,0.521 2.031,0.719 0.458,0.198 10 false COM3 1.677,1.188 2.135,1.385 0.458,0.198 10 false RLV 5.677,0.646 6.313,0.844 0.635,0.198 10 false PRV+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false PRV- 5.979,1.813 6.438,2.01 0.458,0.198 10 false C39 5.99,1.99 6.448,2.188 0.458,0.198 10 false ECM 2.073,0.75 2.531,0.948 0.458,0.198 10 false 2 2.073,1.406 2.531,1.604 0.458,0.198 10 false 1 5.479,0.75 5.938,0.948 0.458,0.198 10 false 2 5.49,1.438 5.948,1.635 0.458,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:
·

After completing repairs, confirm that P1271 and/or P1272 do not recur.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P1272 is output A
P1271 is output B
P1271 and P1272 are output
Other DTCs are output C




A

2.CHECK PRESSURE DISCHARGE VALVE OPERATION

B

7.INSPECT PRESSURE DISCHARGE VALVE RESISTANCE

C

2.CHECK PRESSURE DISCHARGE VALVE OPERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain /Engine / Utility / Pressure Discharge Valve Check.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Engine and ECT > Utility
Tester Display
Pressure Discharge Valve Check
50005 234 2109

d.

Select "Close to Open Check".


e.

Read the value of "Open and Engine OFF".

OK:

0.5 MPa or less


HINT:
·

When the system is normal, the value of "Open and Engine OFF" should be at or close to 0 MPa.

·

When the fuel pressure value of "Open and Engine OFF" does not become equal to or less than 0.5 MPa, the pressure discharge valve may be stuck closed.

·

When the fuel pressure values of "Close and Engine OFF" and "Open and Engine OFF" are both 0 MPa, the pressure discharge valve may be stuck open or there may be a fuel leak.

·

Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.




Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT (DTC P1272)

NG

12.REPLACE COMMON RAIL ASSEMBLY
3.CHECK DTC OUTPUT (DTC P1272)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
P1272 is output A
No DTC is output B



A

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY

B

END

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P1271 and/or P1272.


iii.

Check the DTC judgment result.

HINT:

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.




Result:
Proceed to
NEXT



NEXT

END

7.INSPECT PRESSURE DISCHARGE VALVE RESISTANCE
a.

Inspect the common rail assembly.

Click hereEngine / Hybrid System>2GD-FTV FUEL>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)

NG

12.REPLACE COMMON RAIL ASSEMBLY
8.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)
a.

Disconnect the pressure discharge valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z3-2 (COM3) - C39-2 (PRV+) Always Below 1 Ω
Z3-1 (RLV) - C39-1 (PRV-) Always Below 1 Ω
Z3-2 (COM3) or C39-2 (PRV+) - Body ground and other terminals Always 10 kΩ or higher
Z3-1 (RLV) or C39-1 (PRV-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the pressure discharge valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

9.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC P1271 and/or P1272 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





A

END

B

10.REPLACE ECM
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2GD-FTV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM