Home › Power Source / Network › 1KD-FTV BATTERY / CHARGING › CHARGING SYSTEM › from 2016.01
RM3270E _57 Power Source / Network _048963 1KD-FTV BATTERY / CHARGING _0239226 CHARGING SYSTEM J

1KD-FTV BATTERY / CHARGING  CHARGING SYSTEM  Noise Occurs from V-ribbed Belt or Generator Assembly  


PROCEDURE

1.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptom.


Result:
Symptom Proceed to
Noise occurs from V-ribbed belt A
Noise occurs from generator assembly B



A

2.CHECK FAN AND GENERATOR V BELT FOR WEAR

B

6.CHECK FOR NOISE WHEN ROTOR IS TURNING FREELY
2.CHECK FAN AND GENERATOR V BELT FOR WEAR
a.

Check the fan and generator V belt for wear or damage.

OK:

The fan and generator V belt are not worn or damaged.



Result:
Result
OK
NG



OK

3.CHECK GENERATOR PULLEY WITH CLUTCH FOR WEAR

NG

REPLACE FAN AND GENERATOR V BELT

3.CHECK GENERATOR PULLEY WITH CLUTCH FOR WEAR
a.

Check the grooves of the generator pulley with clutch for wear or damage.

OK:

The grooves of the generator pulley with clutch are not worn or damaged.



Result:
Result
OK
NG



OK

4.CHECK FOR NOISE WHILE CLUTCH PULLEY IS OPERATING

NG

REPLACE GENERATOR PULLEY WITH CLUTCH

4.CHECK FOR NOISE WHILE CLUTCH PULLEY IS OPERATING
a.

Start the engine and check the generator pulley with clutch for looseness.

OK:

The generator pulley with clutch is not loose.



Result:
Result
OK
NG



OK

5.INSPECT GENERATOR PULLEY WITH CLUTCH (UNIT INSPECTION)

NG

TIGHTEN GENERATOR PULLEY WITH CLUTCH TO SPECIFIED TORQUE

5.INSPECT GENERATOR PULLEY WITH CLUTCH (UNIT INSPECTION)
a.

b.

Check the installation condition of the generator pulley cap.

OK:

The generator pulley cap is not loose or missing.



c.

Check for the formation of particles due to friction (for dry type pulley) or grease leaks (for wet type pulley).

OK:

There are no grease leaks (for wet type pulley) or a large amounts of particles (for dry type pulley).



d.

Check the generator pulley with clutch for misalignment (interference with the generator assembly).

OK:

The generator pulley with clutch is not misaligned (no interference with the generator assembly).



e.
A288972

Turn the generator pulley with clutch clockwise and counterclockwise by hand and check for noise.

OK:

Noise does not occur when turned in both directions.



f.

Turn the generator pulley with clutch clockwise and counterclockwise by hand and visually check for runout.

OK:

The generator pulley with clutch does not have runout.



g.
A288971C03
2.365,1.583 2.677,0.896 2.677,0.896 2.927,0.896 false 2.979,0.802 3.292,0.958 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, hold the generator rotor assembly in the generator assembly and check that the generator pulley with clutch locks when turned clockwise and turns freely when turned counterclockwise.

OK:

The generator pulley with clutch locks when turned clockwise and turns freely when turned counterclockwise.



Result:
Result
OK
NG



OK

INSPECT PULLEY OTHER THAN GENERATOR ASSEMBLY PULLEY

NG

REPLACE GENERATOR PULLEY WITH CLUTCH

6.CHECK FOR NOISE WHEN ROTOR IS TURNING FREELY
a.

Perform a road test and check that noise does not occur when decelerating.

OK:

Noise does not occur.



b.

Stop the engine and check that generator pulley with clutch noise does not occur as the engine stops.

OK:

Noise does not occur.



Result:
Result
OK
NG



OK

7.CHECK ENGAGEMENT OF GENERATOR PULLEY WITH CLUTCH

NG

REPLACE GENERATOR PULLEY WITH CLUTCH

7.CHECK ENGAGEMENT OF GENERATOR PULLEY WITH CLUTCH
a.

b.

Using a screwdriver with its tip wrapped with protective tape, hold the generator rotor assembly in the generator assembly and check that the generator pulley with clutch locks when turned from counterclockwise (free turning direction) to clockwise (locking direction).

OK:

The generator pulley with clutch locks.


Result:
Result
OK
NG




OK

REPAIR OR REPLACE GENERATOR ASSEMBLY

NG

REPLACE GENERATOR PULLEY WITH CLUTCH