Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  


DESCRIPTION

The engine speed sensor in the engine control system contains a signal plate and a pickup coil for the NE signal. The NE signal plate has 56 teeth and is mounted in the injection or supply pump assembly.

The NE signal sensor generates 56 signals for every 2 engine revolutions. The ECM detects the engine speed and the cam lift position of the injection or supply pump assembly. The ECM uses the TDC and NE signals for injection timing control. The NE signal is also used for injection volume control.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit
Condition 1:
·

No NE signal to ECM for 0.5 seconds or more at 680 rpm or more.


Condition 2:
·

No NE signal to ECM for 2.0 seconds or more during cranking.


·

Open or short in engine speed sensor circuit

·

Injection or supply pump assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A379036E01
0.573,1.938 2.302,2.146 1.729,0.208 10 false Crankshaft Position Sensor 0.573,1.75 0.979,1.948 0.406,0.198 10 false C183 0.583,3.781 1.021,3.979 0.438,0.198 10 false C176 5.906,4.177 6.344,4.375 0.438,0.198 10 false C175 5.917,4.354 6.354,4.552 0.438,0.198 10 false ECM 0.573,3.969 2.344,4.542 1.771,0.573 10 false Engine Speed Sensor (inside the Injection or Supply Pump Assembly) 3.458,1.708 3.677,1.875 0.219,0.167 10 false * 2.719,3.677 2.938,3.844 0.219,0.167 10 false * 2.708,4.271 3.458,4.5 0.75,0.229 10 false *: Shielded 1.125,2.563 1.531,2.76 0.406,0.198 10 false NE+ 1.125,3.271 1.531,3.469 0.406,0.198 10 false NE- 5.49,2.573 5.896,2.771 0.406,0.198 10 false NE+ 5.49,3.26 5.896,3.458 0.406,0.198 10 false NE- 1.51,2.552 1.917,2.75 0.406,0.198 10 false 2 1.521,3.24 1.927,3.438 0.406,0.198 10 false 1 1.51,1.271 1.917,1.469 0.406,0.198 10 false 2 1.51,0.563 1.917,0.76 0.406,0.198 10 false 1 5.49,0.563 5.969,0.75 0.479,0.188 10 false TDC+ 5.49,1.281 5.969,1.469 0.479,0.188 10 false TDC- 5.177,0.573 5.656,0.76 0.479,0.188 10 false 26 5.188,1.271 5.667,1.458 0.479,0.188 10 false 34 5.198,2.552 5.677,2.74 0.479,0.188 10 false 27 5.208,3.24 5.688,3.427 0.479,0.188 10 false 35

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected.

When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ENGINE SPEED SENSOR
a.

Check the engine speed sensor installation.


b.

Inspect the engine speed sensor.

Click hereEngine / Hybrid System>5L-E FUEL>FUEL INJECTION PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - ENGINE SPEED SENSOR)

NG

REPLACE INJECTION PUMP ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (ECM - ENGINE SPEED SENSOR)
a.

Disconnect the engine speed sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C176-2 - C175-27 (NE+) Always Below 1 Ω
C176-1 - C175-35 (NE-) Always Below 1 Ω
C176-2 or C175-27 (NE+) - Body ground and other terminals Always 10 kΩ or higher
C176-1 or C175-35 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR