Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1115  Coolant Temperature Sensor Circuit for Coolant Heat Storage System / Intake Air Temperature Circuit  


DESCRIPTION

The intake air temperature sensor senses the intake air temperature. A thermistor built in this sensor changes the resistance value according to the intake air temperature as shown in the illustration. This resistance value of intake air temperature sensor is one of the factors used to decide the fuel injection volume.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1115 Coolant Temperature Sensor Circuit for Coolant Heat Storage System / Intake Air Temperature Circuit Open or short in intake air temperature sensor circuit for 0.5 seconds or more.
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor

·

ECM


- DTCstored

WIRING DIAGRAM

A311404E01
0.25,2.219 2.177,2.427 1.927,0.208 10 false Intake Air Temperature Sensor 0.25,2.031 0.563,2.229 0.313,0.198 10 false A75 1.979,0.75 2.292,0.948 0.313,0.198 10 false 2 1.979,1.313 2.292,1.51 0.313,0.198 10 false 1 5.156,0.74 5.469,0.938 0.313,0.198 10 false 22 5.146,1.323 5.458,1.521 0.313,0.198 10 false 30 5.458,0.74 5.771,0.938 0.313,0.198 10 false THA 5.458,1.323 5.875,1.521 0.417,0.198 10 false ETHA 6.042,0.396 6.354,0.594 0.313,0.198 10 false 5V 6,0.667 6.313,0.865 0.313,0.198 10 false R 5.927,2.323 6.344,2.521 0.417,0.198 10 false C175 5.927,2.49 6.344,2.688 0.417,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 61 318

d.

Read the value.

Result:
Display Proceed to
-40°C (-40°F) A
140°C (284°F) or more B
The same as actual engine coolant temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

B

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

C

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.
A110535C01
0.396,3.135 0.844,3.438 0.448,0.302 0.563,0.563 0.74,0.76 0.177,0.198 10 false *1 0.146,2.5 0.354,2.656 0.208,0.156 10 false *a 2.667,0.542 2.906,0.698 0.24,0.156 10 false *2 2.427,1.25 2.771,1.427 0.344,0.177 10 false THA 2.427,1.635 2.885,1.844 0.458,0.208 10 false ETHA 0.5,3.198 0.865,3.354 0.365,0.156 10 false A75
*1 Intake Air Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor)


Disconnect the intake air temperature sensor connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 61 318

f.

Read the value.

OK:

140°C (284°F) or more



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in thetable below.

Standard resistance:
Tester Connection Condition Specified Condition
A75-2 - C175-22 (THA) Always Below 1 Ω
A75-1 - C175-30 (ETHA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.
A076591C01
0.552,0.156 0.865,0.313 0.313,0.156 10 false *1 2.698,0.188 3.01,0.344 0.313,0.156 10 false *2 2.458,0.917 2.917,1.073 0.458,0.156 10 false THA 2.458,1.281 2.917,1.438 0.458,0.156 10 false ETHA
*1 Intake Air Temperature Sensor
*2 ECM


Disconnect the intake air temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 61 318

e.

Read the value.

OK:

-40°C (-40°F) or more



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A75-2 or C175-22 (THA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR