Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1220  Timer Control Circuit  


DESCRIPTION

The ECM controls the injection timing by actuating the timing control valve. The timing control valve is mounted on the injection or supply pump assembly and controls the internal fuel pressure of the pump through duty control.

The ECM detects the injection advance angle based on the TDC and NE signals.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1220 Timer Control Circuit During and after engine warm up, actual injection timing is different from target value of ECM calculated for several second.
·

Open or short in timing control valve circuit

·

Timing control valve

·

Fuel filter element sub-assembly (Clogging)

·

Fuel (Freezing, air present)

·

Injection or supply pump assembly (Internal pressure andtiming control valve)

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A379043E01
0.594,4.052 1.667,4.25 1.073,0.198 10 false FL MAIN 0.573,3.25 1.646,3.448 1.073,0.198 10 false J/B-B 1.99,2.771 4.01,2.979 2.021,0.208 10 false Instrument Panel Junction Block 0.948,1.302 1.219,1.5 0.271,0.198 10 false 2B 0.979,1.094 1.25,1.292 0.271,0.198 10 false 1 1.979,2.354 3.031,2.563 1.052,0.208 10 false EFI MAIN NO. 1 1.104,1.521 2.156,1.729 1.052,0.208 10 false EFI MAIN NO. 1 3,1.469 3.698,1.667 0.698,0.198 10 false EFI NO. 1 3.823,1.313 4.094,1.51 0.271,0.198 10 false 2N 3.844,1.104 4.115,1.302 0.271,0.198 10 false 1 1.49,2.542 1.76,2.74 0.271,0.198 10 false 2J 1.604,2.333 1.875,2.531 0.271,0.198 10 false 5 3.813,2.094 4.083,2.292 0.271,0.198 10 false 2P 3.844,1.885 4.115,2.083 0.271,0.198 10 false 9 4.375,1.698 5.698,1.917 1.323,0.219 10 false Timing Control Valve 4.375,1.531 5.073,1.729 0.698,0.198 10 false C182 5.698,1.302 6.396,1.5 0.698,0.198 10 false C174 5.708,2.094 6.406,2.292 0.698,0.198 10 false G161 5.698,3.667 6.396,3.865 0.698,0.198 10 false C174 5.771,1.094 6.042,1.292 0.271,0.198 10 false 11 5.771,1.896 6.042,2.094 0.271,0.198 10 false 10 5.813,3.469 6.083,3.667 0.271,0.198 10 false 5 6.146,3.667 6.844,3.865 0.698,0.198 10 false E1 6.135,2.104 6.833,2.302 0.698,0.198 10 false MREL 6.135,1.302 6.833,1.5 0.698,0.198 10 false TCV 6.375,4.833 6.781,5.063 0.406,0.229 10 false ECM 0.76,4.844 1.833,5.042 1.073,0.198 10 false Battery 4.521,1.219 4.792,1.417 0.271,0.198 10 false 1 5.26,1.219 5.531,1.417 0.271,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT TIMING CONTROL VALVE ASSEMBLY
a.

Inspect the timing control valve.

Click hereEngine / Hybrid System>5L-E FUEL>FUEL INJECTION PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT TIMING CONTROL VALVE ASSEMBLY (POWER SOURCE)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY (TIMING CONTROL VALVE)

2.INSPECT TIMING CONTROL VALVE ASSEMBLY (POWER SOURCE)
a.
A137676C01
0.583,0.938 1.021,1.219 0.438,0.281 0.156,0.135 0.354,0.302 0.198,0.167 10 false *a 0.635,0.99 1,1.146 0.365,0.156 10 false C182
*1 Front view of wire harness connector
(to Timing Control Valve)


Disconnect the timing control valve connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C182-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TIMING CONTROL VALVE - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TIMING CONTROL VALVE - INSTRUMENT PANEL JUNCTION BLOCK)

3.CHECK HARNESS AND CONNECTOR (TIMING CONTROL VALVE - ECM)
a.

Disconnect the timing control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C182-2 - C174-11 (TCV) Always Below 1 Ω
C182-2 or C174-11 (TCV) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FUEL FILTER ASSEMBLY

NG

END

4.CHECK FUEL FILTER ASSEMBLY
a.

Check the fuel filter element sub-assembly.

Click hereEngine / Hybrid System>5L-E FUEL>FUEL FILTER>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK FUEL LEAK

NG

REPLACE FUEL FILTER ASSEMBLY

5.CHECK FUEL LEAK
a.

Visually check the injection or supply pump assembly, each injector and fuel line for fuel leaks.

Click hereEngine / Hybrid System>5L-E FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION

OK:

No leakage



Result:
Proceed to
OK
NG



OK

6.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPAIR FUEL LEAK

6.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Replace the injection or supply pump assembly.

Click hereEngine / Hybrid System>5L-E FUEL>FUEL INJECTION PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT (DTC P1220 IS OUTPUT AGAIN)
7.CHECK DTC OUTPUT (DTC P1220 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Clear the DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Start the engine.


d.

Idle the engine for 20 sec. or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Read the DTC.

Result:
Display (DTC output) Proceed to
DTC P1220 is output again A
No DTC output B




A

B

END