Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1670  Injection Pump Control Module ROM Test Error  


DESCRIPTION

To compensate for the change in injection volume and injection timing caused by the variance in the injection or supply pump assembly itself, a correction is made by using the data that is stored in the ROM in the injection pump correction unit.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1670 Injection Pump Control Module ROM Test Error

When the ignition switch was turned ON, or when the ECM determines whether it is an error of RAM in ECM or not, the ECM conducts a single communication. If any one of the following status occurs in the communication, the ECM conducts one more communication. While the ECM is conducting the communication, if (a) is duplicated 20 times continuously, or if (b) is duplicated 20 times continuously, or if (c) is duplicated 2 times continuously, the ECM outputs the DTC P1670.

1.

There was a communication error when receiving data.

2.

Data sent from the injection pump correction unit does not match to the data received from the ECM.

3.

Data received from the pump ROM is not input in the period of 1024 msec.



Although the determining process is completed without a problem, the ECM conducts the communication again if an undefined code is found while checking an identification code of the receiving data. If the undefined code was duplicated 20 times in a row, the ECM outputs the DTC.
·

Open or short in injection or supply pump assembly correction unit circuit

·

Injection pump correction unit (Injection or supply pump assembly)

·

ECM


- DTC stored

WIRING DIAGRAM

A311407E01
1.198,1.604 1.813,1.802 0.615,0.198 10 false DATA 1.292,2.302 1.906,2.5 0.615,0.198 10 false CLK 1.385,3.01 2,3.208 0.615,0.198 10 false E1 5.427,1.615 6.042,1.813 0.615,0.198 10 false DATA 5.427,2.313 6.042,2.51 0.615,0.198 10 false CLK 5.427,3.021 6.042,3.219 0.615,0.198 10 false E1 1.698,1.469 2.042,1.677 0.344,0.208 10 false 1 1.708,2.167 2.052,2.375 0.344,0.208 10 false 4 1.698,2.865 2.042,3.073 0.344,0.208 10 false 2 0.469,3.854 1.083,4.052 0.615,0.198 10 false C177 0.469,4.042 2.5,4.26 2.031,0.219 10 false Injection Pump Correction Unit 2.885,3.833 3.802,4.073 0.917,0.24 10 false *: Shielded 3.427,1.208 3.771,1.417 0.344,0.208 10 false * 5.094,1.469 5.438,1.677 0.344,0.208 10 false 29 5.094,2.177 5.438,2.385 0.344,0.208 10 false 28 5.146,2.875 5.49,3.083 0.344,0.208 10 false 5 5.781,3.844 6.396,4.042 0.615,0.198 10 false C174 5.781,4.031 6.396,4.229 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - INJECTION PUMP CORRECTION UNIT)
a.

Disconnect the injection pump correction unit connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C177-1 (DATA) - C174-29 (DATA) Always Below 1 Ω
C177-4 (CLK) - C174-28 (CLK) Always Below 1 Ω
C177-1 (DATA) or C174-29 (DATA) - Body ground and other terminals Always 10 kΩ or higher
C177-4 (CLK) or C174-28 (CLK) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Replace the injection or supply pump assembly.

Click hereEngine / Hybrid System>5L-E FUEL>FUEL INJECTION PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.READ DTC OUTPUT (DTC P1670 IS OUTPUT AGAIN)
3.READ DTC OUTPUT (DTC P1670 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Clear the DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch to ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Display (DTC output) Proceed to
DTC P1670 is output again A
No DTC output B




A

B

SYSTEM OK