Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  VC Output Circuit  


DESCRIPTION

The VC voltage (5 V) is generated in the ECM. The voltage is used to supply power to the manifold absolute pressure sensor and accelerator pedal position sensor.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source circuit.

Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECD SYSTEM>ECM Power Source Circuit

·

VC Power Source Circuit


A362200E01
0.479,3.115 2.667,3.344 2.188,0.229 10 false Accelerator Pedal Position Sensor 0.479,2.938 0.844,3.135 0.365,0.198 10 false A30 0.479,4.885 0.823,5.073 0.344,0.188 10 false C53 0.479,5.073 2.708,5.302 2.229,0.229 10 false Manifold Absolute Pressure Sensor 1.719,0.583 2.156,0.781 0.438,0.198 10 false VPA 1.729,0.969 2.167,1.167 0.438,0.198 10 false EPA 1.646,1.354 2.083,1.552 0.438,0.198 10 false VCPA 1.677,1.74 2.115,1.938 0.438,0.198 10 false VPA2 1.688,2.125 2.125,2.323 0.438,0.198 10 false EPA2 1.688,2.51 2.125,2.708 0.438,0.198 10 false VCP2 2.167,0.469 2.604,0.667 0.438,0.198 10 false 6 2.167,0.854 2.604,1.052 0.438,0.198 10 false 5 2.167,1.24 2.604,1.438 0.438,0.198 10 false 4 2.167,1.625 2.604,1.823 0.438,0.198 10 false 3 2.167,2.01 2.604,2.208 0.438,0.198 10 false 2 2.167,2.396 2.604,2.594 0.438,0.198 10 false 1 1.844,3.646 2.281,3.844 0.438,0.198 10 false VC 1.813,4.042 2.25,4.24 0.438,0.198 10 false PIM 1.938,4.448 2.375,4.646 0.438,0.198 10 false E 2.177,3.521 2.615,3.719 0.438,0.198 10 false 3 2.188,3.917 2.625,4.115 0.438,0.198 10 false 2 2.188,4.323 2.625,4.521 0.438,0.198 10 false 1 5.646,0.583 6.083,0.781 0.438,0.198 10 false VPA 5.656,0.969 6.094,1.167 0.438,0.198 10 false EPA 5.646,1.365 6.083,1.563 0.438,0.198 10 false VCPA 5.635,1.75 6.073,1.948 0.438,0.198 10 false VPA2 5.635,2.135 6.073,2.333 0.438,0.198 10 false EPA2 5.625,2.531 6.063,2.729 0.438,0.198 10 false VCP2 5.198,0.583 5.635,0.781 0.438,0.198 10 false G161 5.188,0.969 5.625,1.167 0.438,0.198 10 false G161 5.198,1.354 5.635,1.552 0.438,0.198 10 false G161 5.198,1.75 5.635,1.948 0.438,0.198 10 false G161 5.198,2.125 5.635,2.323 0.438,0.198 10 false G161 5.198,2.521 5.635,2.719 0.438,0.198 10 false G161 5.271,0.396 5.708,0.594 0.438,0.198 10 false 20 5.271,0.792 5.708,0.99 0.438,0.198 10 false 27 5.271,1.177 5.708,1.375 0.438,0.198 10 false 26 5.271,1.563 5.708,1.76 0.438,0.198 10 false 28 5.271,1.948 5.708,2.146 0.438,0.198 10 false 29 5.271,2.333 5.708,2.531 0.438,0.198 10 false 23 5.198,3.635 5.635,3.833 0.438,0.198 10 false C175 5.188,4.031 5.625,4.229 0.438,0.198 10 false C175 5.188,4.438 5.625,4.635 0.438,0.198 10 false C175 5.635,3.635 6.135,3.833 0.5,0.198 10 false VCPM 5.635,4.052 6.073,4.25 0.438,0.198 10 false PIM 5.635,4.448 6.073,4.646 0.438,0.198 10 false EPIM 5.271,3.448 5.771,3.646 0.5,0.198 10 false 24 5.271,3.854 5.771,4.052 0.5,0.198 10 false 33 5.271,4.25 5.771,4.448 0.5,0.198 10 false 32 5.99,5.375 6.427,5.573 0.438,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and GTS on.


c.

Check the communication between the GTS and ECM.

Result:
Condition Proceed to
Communication is not possible A
Communication is possible B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.

Turn the ignition switch to ON.


b.
A080463C88
0.583,0.198 0.99,0.458 0.406,0.26 2.51,0.208 2.927,0.469 0.417,0.26 0.656,0.792 0.406,1.5 true 3,0.792 3.01,1.531 true 0.635,0.25 1.021,0.448 0.385,0.198 10 false C174 2.563,0.26 2.99,0.458 0.427,0.198 10 false G161 0.229,1.531 0.677,1.729 0.448,0.198 10 false 5 (E1) 2.854,1.542 3.313,1.74 0.458,0.198 10 false 1 (+B) 0.042,0.094 0.271,0.271 0.229,0.177 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G161-1 (+B) - C174-5 (E1) IG ON 11 to 14 V



HINT:

If the result is not as specified, since current is not flowing to the +B terminals of the ECM, the system may not be started.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B



e.

Reconnect the accelerator pedal position sensor connector.



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B



e.

Reconnect the manifold absolute pressure sensor connector.



A

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the ECM connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C175-24 (VCPM) - Body ground and other terminals Always 10 kΩ or higher
G161-26 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
G161-23 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
G161-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



e.

Reconnect the manifold absolute pressure sensor connector.


f.

Reconnect the accelerator pedal position sensor connector.


g.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR