Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _049378 1KD-FTV ENGINE CONTROL _0236318 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, Data List items Stop Light SW is ON when the brake pedal is depressed.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IG2 NO. 3 fuse

·

Stop light switch assembly

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0504 Depress and release brake pedal with ignition switch ON

WIRING DIAGRAM

A379271E01
0.688,2.49 1.469,2.688 0.781,0.198 10 false AM2 NO. 2 0.417,2.802 1.198,3 0.781,0.198 10 false J/B-B 1.427,3.583 2.208,3.781 0.781,0.198 10 false ALT 2.927,3.563 3.708,3.76 0.781,0.198 10 false STOP 0.438,4.115 1.219,4.313 0.781,0.198 10 false FL MAIN 3.635,2.49 4.417,2.688 0.781,0.198 10 false IG2 NO. 3 2.833,1.469 3.615,1.667 0.781,0.198 10 false IG2 1.708,2.698 2.49,2.896 0.781,0.198 10 false G135 1.719,2.854 3.354,3.063 1.635,0.208 10 false Ignition Switch Assembly 1.906,2.24 2.688,2.438 0.781,0.198 10 false AM2 2.688,2.229 3.469,2.427 0.781,0.198 10 false IG2 1.719,2.229 1.979,2.406 0.26,0.177 10 false 4 2.99,2.229 3.25,2.406 0.26,0.177 10 false 3 3.281,1.01 3.542,1.188 0.26,0.177 10 false 3 3.292,0.531 3.552,0.708 0.26,0.177 10 false 1 2.51,1.01 2.771,1.188 0.26,0.177 10 false 5 2.51,0.531 2.771,0.708 0.26,0.177 10 false 2 4.219,1.031 5,1.229 0.781,0.198 10 false G16 4.219,1.198 7.156,1.406 2.938,0.208 10 false Cenrtification ECU (Smart Key ECU Assembly) 5.375,2.219 5.635,2.396 0.26,0.177 10 false 5 5.365,3.302 5.625,3.479 0.26,0.177 10 false 3 4.375,3.313 4.635,3.49 0.26,0.177 10 false 7 4.375,2.229 4.635,2.406 0.26,0.177 10 false 6 4.365,3.729 4.625,3.906 0.26,0.177 10 false 2 4.104,4.24 4.469,4.396 0.365,0.156 10 false A64 4.115,4.417 5.938,4.688 1.823,0.271 10 false Stop Light Switch Assembly 6.24,4.375 6.625,4.531 0.385,0.156 10 false G140 6.25,4.552 6.635,4.708 0.385,0.156 10 false ECM 5.688,3.313 5.948,3.49 0.26,0.177 10 false 15 5.708,2.219 5.969,2.396 0.26,0.177 10 false 14 4.552,0.646 5.333,0.844 0.781,0.198 10 false IG1D 4.271,0.542 4.531,0.719 0.26,0.177 10 false 20 0.604,4.896 1.385,5.094 0.781,0.198 10 false Battery 1.438,2.229 1.646,2.417 0.208,0.188 10 false *1 3.188,2.208 3.396,2.396 0.208,0.188 10 false *1 3.583,1.396 3.792,1.583 0.208,0.188 10 false *2 1.156,1.385 1.365,1.573 0.208,0.188 10 false *2 1.438,4.875 3.938,5.115 2.5,0.24 10 false *1: w/o Smart Entry and Start System 1.469,5.167 3.969,5.406 2.5,0.24 10 false *2: w/ Smart Entry and Start System 5.938,2.219 6.333,2.396 0.396,0.177 10 false ST1- 5.948,3.313 6.302,3.49 0.354,0.177 10 false STP 4.552,2.323 4.813,2.5 0.26,0.177 10 false B 4.552,3.406 4.813,3.583 0.26,0.177 10 false B 4.563,3.833 4.896,4.01 0.333,0.177 10 false GND 5.167,3.406 5.427,3.583 0.26,0.177 10 false L 5.177,2.323 5.438,2.5 0.26,0.177 10 false L

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

5.

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)
a.
E270270C09
0.208,1.073 0.656,1.375 0.448,0.302 2.042,1.208 1.479,1.823 true 2.375,1.188 2.792,1.854 true 0.302,1.146 0.76,1.344 0.458,0.198 10 false A64 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.406,1.865 1.563,2.063 0.156,0.198 10 false B 2.781,1.896 2.938,2.094 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the igntion switch to ON


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-6 (B) - Body ground Ignition switch ON 11 to 14 V
A64-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY,INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A303106C14
1.938,2.531 2.385,2.802 0.448,0.271 1.552,3.938 1.927,3.177 true 2.333,3.906 1.979,3.177 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.771,0.083 2.083,0.281 0.313,0.198 10 false *b 0.25,2.219 0.563,2.417 0.313,0.198 10 false *c 2,2.573 2.458,2.781 0.458,0.208 10 false G140 1.292,3.948 1.896,4.198 0.604,0.25 10 false 15 (STP) 2.271,3.948 2.896,4.198 0.625,0.25 10 false 14 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G140-14 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
G140-15 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-3 (L) - G140-15 (STP) Always Below 1 Ω
A64-5 (L) - G140-14 (ST1-) Always Below 1 Ω
A64-3 (L) or G140-15 (STP) - Body ground and other terminals Always 10 kΩ or higher
A64-5 (L) or G140-14 (ST1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR