When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
16575C
1.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
Install the No. 1 water hose clamp bracket with the bolt to the timing chain case assembly.
13471
2.INSTALL CRANKSHAFT PULLEY
11382C
3.INSTALL CAMSHAFT OIL SEAL RETAINER
If the camshaft oil seal retainer is dropped, replace it with a new one.
Before installing a new camshaft oil seal retainer, clean the installation surface of the No. 3 camshaft bearing cap and cylinder head sub-assembly and remove any foreign matter.
| *1 | Camshaft Oil Seal Retainer |
| *a | Depth |
Using SST and a hammer, tap in a new camshaft oil seal retainer to the No. 3 camshaft bearing cap and cylinder head sub-assembly as shown in the illustration.
-0.5 to 0.8 mm (-0.0197 to 0.0315 in.)
29300
4.INSTALL VACUUM PUMP ASSEMBLY
Coat 2 new O-rings with engine oil, and install them to the vacuum pump assembly.
Install the vacuum pump assembly so that the coupling teeth of the vacuum pump assembly labeled A and the groove of the No. 2 camshaft labeled B can engage.
Install the vacuum pump assembly with the 3 bolts to the cylinder head sub-assembly.
25706
5.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Install the No. 1 vacuum transmitting pipe sub-assembly with the 3 bolts to the cylinder head sub-assembly.
Connect the No. 1 vacuum transmitting hose to the vacuum pump assembly.
16620
6.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
16603
7.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
16331A
8.INSTALL THERMOSTAT
16321
9.INSTALL WATER INLET
Install the water inlet with the 3 bolts to the timing chain cover sub-assembly.
16304
10.INSTALL WATER OUTLET SUB-ASSEMBLY
Install a new gasket and the water outlet sub-assembly with the 4 bolts and 2 nuts to the timing chain cover sub-assembly.
16207
11.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 2 water by-pass pipe sub-assembly with the 2 bolts to the engine water pump assembly and water inlet.
Connect the No. 3 water by-pass hose to the water outlet sub-assembly, and slide the clamp to secure the hose.
83530
12.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
15407
13.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY
17141
14.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
15474
15.INSTALL TURBO OIL OUTLET PIPE
17293
16.TEMPORARILY INSTALL TURBOCHARGER STAY
17141
17.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
17293
18.TIGHTEN TURBOCHARGER STAY
16284
19.CONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
16268
20.INSTALL NO. 1 WATER BY-PASS PIPE
Install a new gasket and the No. 1 water by-pass pipe with the 3 bolts to the timing chain cover sub-assembly.
Make sure that the claw of the gasket faces the No. 1 water by-pass pipe.
16279
21.INSTALL NO. 3 WATER BY-PASS PIPE
12261
22.INSTALL PCV HOSE
25051
23.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
24.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY
17271
25.INSTALL NO. 1 TURBO INSULATOR
17167
26.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
89467B
27.INSTALL AIR FUEL RATIO SENSOR (w/ DPF)
17168
28.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
23295D
29.INSTALL NO. 1 INJECTOR HOLDER (w/ DPF)
16281
30.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
Connect the No. 4 water by-pass hose to the No. 1 injector holder, and slide the clamp to secure the hose.
16282
31.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)
Attach the clamp and install the No. 5 water by-pass hose to the No. 1 water hose clamp bracket.
Connect the No. 5 water by-pass hose to the No. 1 injector holder and water outlet sub-assembly, and slide the 2 clamps to secure the hose.
89422C
32.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
88431
33.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET
Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.
Temporarily install the No. 1 compressor mounting bracket with the 2 bolts to the cylinder block sub-assembly.
Temporarily install the No. 1 compressor mounting bracket with the 2 bolts so that the No. 1 compressor mounting bracket can be moved by hand.
| *a | No Clearance |
| *b | Push |
| *c | Front |
Push the No. 1 compressor mounting bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.
Make sure there is no clearance between the cylinder block sub-assembly and No. 1 compressor mounting bracket as shown in the illustration.
Uniformly tighten the 3 bolts in the order shown in the illustration.
16025
34.INSTALL NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY
Install a new gasket and the No. 5 water by-pass pipe sub-assembly with the 3 bolts to the cylinder block sub-assembly.
Make sure that the claw of the gasket faces the No. 5 water by-pass pipe sub-assembly.
23780
35.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)
Install the No. 3 nozzle leakage pipe with the 2 nuts to the cylinder block sub-assembly.
23300D
36.INSTALL DIESEL FUEL FILTER ASSEMBLY (w/ DPF)
Install the diesel fuel filter assembly with the 2 nuts to the cylinder block sub-assembly.
44781
37.INSTALL HOSE BRACKET
Install the hose bracket with the 2 bolts to the cylinder head sub-assembly.
19850
38.INSTALL GLOW PLUG ASSEMBLY
19871
39.INSTALL NO. 1 GLOW PLUG CONNECTOR
23810A
40.INSTALL COMMON RAIL ASSEMBLY
23701
41.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23670
42.TIGHTEN INJECTOR ASSEMBLY
23701
43.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
44.INSTALL WIRING HARNESS CLAMP BRACKET
Install the 2 wiring harness clamp brackets with the 2 bolts to the cylinder head cover sub-assembly.
23760
45.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY
23811H
46.INSTALL NO. 1 FUEL PIPE (w/ DPF)
47.INSTALL WIRING HARNESS CLAMP BRACKET
17111
48.INSTALL INTAKE MANIFOLD
23770
49.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
23804C
50.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
23815D
51.INSTALL NO. 3 FUEL PIPE (w/ DPF)
23804D
52.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)
23271H
53.INSTALL NO. 1 FUEL HOSE
23273H
54.INSTALL NO. 2 FUEL HOSE
23243B
55.INSTALL FUEL PUMP MOTOR WIRE
22803
56.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY
17118
57.INSTALL MANIFOLD STAY
58.INSTALL WIRING HARNESS CLAMP BRACKET
23812D
59.INSTALL NO. 2 FUEL PIPE
Install the No. 2 fuel pipe with the bolt to the manifold stay.
Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.
11409
60.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
25800
61.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
16209
62.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 4 water by-pass pipe sub-assembly with the 2 bolts to the intake manifold.
Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.
Connect the No. 7 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
25804
63.INSTALL VACUUM CONTROL VALVE SET
25601
64.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install 2 new gaskets and the No. 1 EGR pipe sub-assembly with the bolt and 4 new nut to the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.
27148A
65.INSTALL CONNECTING WIRE
Attach the 2 clamps and install the connecting wire to the hose bracket.
Connect the connector to the common rail assembly.
16206B
66.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
25612
67.INSTALL NO. 2 EGR PIPE
25625
68.INSTALL EGR VALVE BRACKET
89421C
69.INSTALL DIESEL TURBO PRESSURE SENSOR
23265C
70.INSTALL GAS FILTER
12631A
71.INSTALL ENGINE COVER BRACKET
Install the engine cover bracket with the 2 bolts to the cylinder head cover sub-assembly and hose bracket.
17578B
72.INSTALL PIPE CLAMP (w/ DPF)
25734
73.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)
25733A
74.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)
25734
75.TIGHTEN NO. 2 VACUUM PIPE (w/ DPF)
25733A
76.TIGHTEN NO. 1 VACUUM PIPE (w/ DPF)
89425
77.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
89481B
78.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
16278
79.INSTALL NO. 2 WATER BY-PASS PIPE
26100G
80.INSTALL DIESEL THROTTLE BODY ASSEMBLY
17363K
81.INSTALL INTERCOOLER AIR TUBE
82121
82.INSTALL ENGINE WIRE
12632
83.INSTALL NO. 2 ENGINE COVER BRACKET
44763C
84.INSTALL NO. 2 HOSE TO HOSE TUBE
Install the No. 2 hose to hose tube to the cylinder head cover sub-assembly and hose bracket with the 2 bolts.
Connect the union to check valve hose to the vacuum pump assembly, and slide the clamp to secure the hose.