Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2016.01
RM3270E _51 Engine / Hybrid System _048939 2TR-FE ENGINE MECHANICAL _0242508 CYLINDER HEAD GASKET A

2TR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P0630 is output (Click here)
Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly Inspection after repair Poor idle, engine start, etc. (Click here)
·

Replacement of throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of fuel injector assembly

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection after repair Poor idle, engine start, etc. (Click here)
for AC60E:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60E:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for AC60F:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60F:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 11302 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 3.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11204 4.REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

Hide 13540 6.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 7.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 8.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 9.REMOVE CHAIN SUB-ASSEMBLY

Hide 10.REMOVE CAMSHAFT BEARING CAP

a.
A336452N01
0.49,0.156 0.615,0.344 0.125,0.188 10 true 1 0.5,1.885 0.625,2.073 0.125,0.188 10 true 2 0.198,0.656 0.323,0.844 0.125,0.188 10 true 3 0.219,1.458 0.344,1.646 0.125,0.188 10 true 4 2.823,0.208 2.948,0.396 0.125,0.188 10 true 5 3.052,1.063 3.177,1.25 0.125,0.188 10 true 6 2.813,1.823 2.938,2.01 0.125,0.188 10 true 7 2.615,0.948 2.74,1.125 0.125,0.177 10 true 8 0.969,0.219 1.094,0.406 0.125,0.188 10 true 9 1.115,1.104 1.313,1.281 0.198,0.177 10 true 10 0.938,1.813 1.135,2.01 0.198,0.198 10 true 11 0.698,0.948 0.906,1.125 0.208,0.177 10 true 12 2.156,0.219 2.354,0.417 0.198,0.198 10 true 13 2.333,1.104 2.531,1.302 0.198,0.198 10 true 14 2.177,1.823 2.375,2.021 0.198,0.198 10 true 15 1.958,0.948 2.167,1.125 0.208,0.177 10 true 16 1.542,0.219 1.74,0.417 0.198,0.198 10 true 17 1.719,1.104 1.917,1.302 0.198,0.198 10 true 18 1.552,1.823 1.75,2.021 0.198,0.198 10 true 19 1.354,0.938 1.552,1.125 0.198,0.188 10 true 20

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshafts level.



b.
A337665

Remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 11.REMOVE CAMSHAFT

a.
A336453

Remove the camshaft.


Hide 13512 12.REMOVE NO. 2 CAMSHAFT

a.
A336455

Remove the No. 2 camshaft.


Hide 13801 13.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A336447C01
1.979,0.438 2.229,0.229 2.229,0.229 2.438,0.229 false 2.302,1.385 2.719,1.385 true 0.719,0.74 1.25,0.74 true 2.458,0.125 2.656,0.313 0.198,0.188 10 false *1 2.76,1.281 2.958,1.458 0.198,0.177 10 false *2 0.521,0.635 0.708,0.823 0.188,0.188 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Remove the 16 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 14.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 15.REMOVE VALVE STEM CAP

a.
A101315

Remove the 16 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 16.DISCONNECT ENGINE WIRE

a.
A348631

Remove the 3 bolts and disconnect the engine wire from the cylinder head sub-assembly.


Hide 11101 17.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A356064

w/ Oil Cooler:

Remove the bolt and disconnect the No. 4 water by-pass pipe.


b.
A302544N09
0.531,1.792 0.688,1.99 0.156,0.198 10 true 1 2.99,0.25 3.146,0.448 0.156,0.198 10 true 2 0.531,0.26 0.688,0.458 0.156,0.198 10 true 3 3,1.802 3.156,2 0.156,0.198 10 true 4 1.156,0.26 1.313,0.458 0.156,0.198 10 false 5 2.385,1.802 2.542,2 0.156,0.198 10 false 6 1.125,1.792 1.281,1.99 0.156,0.198 10 false 7 2.385,0.271 2.542,0.469 0.156,0.198 10 false 8 1.76,1.813 1.917,2.01 0.156,0.198 10 false 9 1.708,0.26 1.927,0.438 0.219,0.177 10 false 10

Uniformly loosen the 10 cylinder head set bolts in the sequence shown in the illustration. Remove the 10 cylinder head set bolts and plate washers.

NOTICE:
·

Be careful not to drop the washers into the cylinder head sub-assembly.

·

Head warpage or cracking could result from removing the cylinder head set bolts in the wrong order.




c.

Remove the cylinder head sub-assembly.


Hide 11115 18.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 19.INSPECT CYLINDER HEAD SET BOLT

Hide 20.INSPECT CYLINDER HEAD SUB-ASSEMBLY