Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.01
RM3270E _51 Engine / Hybrid System _048939 2TR-FE ENGINE MECHANICAL _0242512 ENGINE UNIT A

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 83530 2.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 4.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 12108 5.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap.


b.

Remove the gasket from the oil filler cap sub-assembly.


Hide 12204 6.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 11301M 7.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 8.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11301K 9.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11101J 10.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11201 12.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12233 13.REMOVE NO. 1 VENTILATION CONNECTOR

a.
A340619

Remove the 2 bolts and No. 1 ventilation connector from the cylinder head cover sub-assembly.


Hide 16321 14.REMOVE WATER INLET

Hide 16331A 15.REMOVE THERMOSTAT

Hide 13471 16.REMOVE CRANKSHAFT PULLEY

Hide 12144 17.REMOVE OIL PAN COVER SILENCER

Hide 12102A 18.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 19.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12101 20.REMOVE OIL PAN SUB-ASSEMBLY

Hide 11421 21.REMOVE OIL PAN STUD BOLT

NOTICE:

If an oil pan stud bolt is deformed or its threads are damaged, replace it.


Hide 16620D 22.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11302 23.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 24.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11303A 25.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 26.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A336450C01
0.427,2 0.594,2 0.594,2 0.885,2.323 true 2.896,2.031 2.76,2.031 2.76,2.031 2.49,2.365 true 2.885,3.75 2.75,3.75 2.75,3.75 1.771,3.917 true 1.833,4.031 2.063,4.302 2.063,4.302 2.063,4.417 true 2.698,0.938 2.052,1.083 2.052,1.083 2.708,0.698 true 1.125,0.573 1.333,1.281 1.333,1.281 1,0.781 true 2.927,3.646 3.125,3.875 0.198,0.229 10 false *1 1.281,1.302 1.479,1.51 0.198,0.208 10 true *a 1.052,0.042 1.24,0.24 0.188,0.198 10 true *b 1.76,3.313 1.958,3.5 0.198,0.188 10 true *c 1.865,0.99 2.063,1.198 0.198,0.208 10 true *a 2.938,1.917 3.135,2.125 0.198,0.208 10 true *a 0.229,1.885 0.427,2.094 0.198,0.208 10 true *a 1.979,4.427 2.177,4.635 0.198,0.208 10 true *a
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Approximately 13°
*c Approximately 30°


Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



c.

Remove the crankshaft pulley bolt.


Hide 11204 27.REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

a.
A336454

Remove the 2 bolts and cylinder head cover connector sub-assembly.


b.

Remove the No. 2 camshaft bearing cap oil hole gasket and 3 No. 3 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap.


Hide 13566B 28.REMOVE TIMING CHAIN GUIDE

a.
A336451C01
0.646,1.729 0.875,1.729 0.875,1.729 1.552,1.063 true 0.438,1.625 0.635,1.813 0.198,0.188 10 false *1
*1 O-Ring


Remove the 2 bolts, timing chain guide and O-ring.


Hide 13540 29.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
A101303C25
1.854,1.531 2.104,1.708 2.104,1.708 2.24,1.708 true 2.323,0.781 2.552,0.344 2.552,0.344 2.677,0.344 true 0.563,1.854 0.563,1.521 false 2.26,1.615 2.49,1.792 0.229,0.177 10 false *b 0.5,1.875 0.698,2.063 0.198,0.188 10 false *c 2.729,0.25 2.917,0.458 0.188,0.208 10 false *a
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


·

When the No. 1 chain tensioner assembly is removed, do not rotate the crankshaft.

·

When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.



a.

Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.


c.
A340033

Remove the bolt, nut, No. 1 chain tensioner assembly and gasket.


Hide 13559 30.REMOVE CHAIN TENSIONER SLIPPER

a.
A340035

Remove the bolt and chain tensioner slipper.


Hide 13561 31.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A340037

Remove the bolt, nut and No. 1 chain vibration damper.


Hide 13506 32.REMOVE CHAIN SUB-ASSEMBLY

Hide 13521 33.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A101308

Remove the crankshaft timing gear or sprocket from the crankshaft.


Hide 13801 37.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 38.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 13050 40.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 41.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 42.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13070A 43.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11101 44.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 15678A 46.REMOVE OIL CONTROL VALVE FILTER

a.
A101413

Using an 8 mm hexagon wrench, remove the screw plug.


b.

Remove the oil control valve filter and gasket.


Hide 13562 47.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A101320C09
1.208,1.063 0.969,1.938 0.969,1.938 0.813,1.938 true 0.573,1.333 0.385,0.781 0.385,0.781 0.26,0.781 true 2.708,0.781 2.708,1.219 false 0.063,0.677 0.24,0.875 0.177,0.198 10 false *a 0.615,1.833 0.813,2.031 0.198,0.198 10 false *b 2.656,1.25 2.854,1.448 0.198,0.198 10 false *c
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


Move the stopper plate downward to release the lock and push the plunger deep into the No. 2 chain tensioner assembly.


b.

Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.


c.
A302681

Remove the bolt and No. 2 chain vibration damper.


Hide 13563 48.REMOVE NO. 3 CHAIN VIBRATION DAMPER

a.
A302682

Remove the 2 bolts and No. 3 chain vibration damper.


Hide 13550 49.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A302683

Remove the hexagon wrench from the No. 2 chain tensioner assembly.


b.

Remove the nut and No. 2 chain tensioner assembly.


Hide 13507 50.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

a.
A101324

Remove the bolt, balanceshaft drive gear shaft and balanceshaft drive gear.


b.

Remove the No. 2 crankshaft timing sprocket and No. 2 chain sub-assembly.


Hide 13554 51.REMOVE NO. 4 CHAIN VIBRATION DAMPER

a.
A302684

Remove the 2 bolts and No. 4 chain vibration damper.


Hide 13471A 52.REMOVE CRANKSHAFT PULLEY SET KEY

a.
A101326

Remove the 2 crankshaft pulley set keys from the crankshaft.


Hide 16288 53.REMOVE NO. 4 WATER BY-PASS PIPE (w/ Oil Cooler)

a.
A356093

Disconnect the No. 5 water by-pass hose from the oil cooler assembly.


b.

Remove the 2 bolts and No. 4 water by-pass pipe.


Hide 16281 54.REMOVE NO. 4 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A356094

Slide the 2 clips and remove the No. 4 water by-pass hose from the oil cooler assembly and union.


Hide 15601 55.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15710 56.REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)

Hide 15600A 57.REMOVE OIL FILTER UNION (w/o Oil Cooler)

a.
A348634

Using a 27 mm socket wrench, remove the oil filter union.


Hide 15609 58.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
A348635

Remove the 2 bolts and nut from the oil filter bracket.


b.

Remove the 2 screw plugs and 2 gaskets from the oil filter bracket sub-assembly.


c.
A348636C01
1.823,2.979 2.365,2.979 true 0.99,0.917 2.448,0.583 2.448,0.583 2.656,0.583 true 2.688,0.479 2.885,0.656 0.198,0.177 10 false *1 1.635,2.885 1.823,3.083 0.188,0.198 10 false *2
*1 O-Ring
*2 Oil Filter Bracket Gasket


Remove the oil filter bracket gasket and O-ring.


d.
A346833

Using a hexagon wrench, remove the oil filter bracket union.


Hide 15777E 59.REMOVE UNION (w/ Oil Cooler)

a.
A356095

Remove the union from the cylinder block sub-assembly.


Hide 11432A 60.REMOVE NO. 1 TAPER SCREW PLUG (w/o Oil Cooler)

a.
A346834

Remove the No. 1 taper screw plug from the cylinder block sub-assembly.


Hide 11381 61.REMOVE REAR ENGINE OIL SEAL RETAINER

a.

Remove the 6 bolts.


b.
A346835C01
0.354,1.51 0.479,1.51 0.479,1.51 1.552,1.063 true 0.146,1.406 0.354,1.604 0.208,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip taped, pry out the rear engine oil seal retainer.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11381A 62.REMOVE REAR ENGINE OIL SEAL

a.
A346836C01
1.74,1.958 0.75,1.958 0.75,1.958 1.052,1.531 true 1.76,1.052 2.146,0.844 2.146,0.844 2.323,0.844 true 2.354,0.74 2.552,0.948 0.198,0.208 10 false *a 0.542,1.854 0.74,2.063 0.198,0.208 10 false *b
*a Protective Tape
*b Wooden Blocks


Place the rear engine oil seal retainer on wooden blocks.


b.

Using a screwdriver with its tip taped and a hammer, tap out the rear engine oil seal.

HINT:

Tape the screwdriver tip before use.