Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › from 2016.01
RM3270E _51 Engine / Hybrid System _048939 2TR-FE ENGINE MECHANICAL _0242510 REAR CRANKSHAFT OIL SEAL A

2TR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Gas leaks from exhaust system Inspection after repair Poor idle, engine start, etc. (Click here)
for AC60E:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60E:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for AC60F:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60F:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 33030 1.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 31210 3.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 4.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 5.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A348627C01
2.406,1.896 2.604,2.115 0.198,0.219 10 false *a
*a Hold


Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A346812

Remove the 10 bolts and flywheel sub-assembly.


Hide 32101 6.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.
A348627C01
2.406,1.896 2.604,2.115 0.198,0.219 10 false *a
*a Hold


Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A346813

Remove the 10 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly and front drive plate spacer.


Hide 11381A 7.REMOVE REAR ENGINE OIL SEAL

a.
A346814C01
0.635,1.563 0.865,1.938 0.865,1.938 0.969,1.938 true 1.708,1.115 0.615,0.458 0.615,0.458 0.427,0.458 true 1,1.833 1.229,2.167 0.229,0.333 10 true *a 0.25,0.365 0.427,0.542 0.177,0.177 10 false *b
*a Cut Position
*b Protective Tape


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:
·

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.

·

After removing the rear engine oil seal, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.



HINT:

Tape the screwdriver tip before use.