Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM › from 2016.01
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205695 BACK DOOR CLOSER SYSTEM C

DOOR / HATCH  BACK DOOR CLOSER SYSTEM  B2250  Back Door Closer Operation Malfunction  


DESCRIPTION

The multiplex network door ECU receives signals from the half latch switch, initial switch, pawl switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock assembly is determined.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2250 Back Door Closer Operation Malfunction While the back door closer is operating, a malfunction is detected in position information from the initial switch within a specified amount of time.
·

Back door lock assembly

·

Harness or connector

·

Multiplex network door ECU



WIRING DIAGRAM

w/ Power Back Door
B411291E04
0.521,4.177 4.042,4.375 3.521,0.198 10 false Back Door Lock Assembly 4.938,4.271 7.156,4.521 2.219,0.25 10 false Multiplex Network Door ECU 4.344,1.531 4.802,1.729 0.458,0.198 10 false V12 4.333,2.073 4.792,2.271 0.458,0.198 10 false V12 4.344,2.635 4.802,2.833 0.458,0.198 10 false V12 4.323,3.198 4.781,3.396 0.458,0.198 10 false V12 4.333,0.448 4.792,0.646 0.458,0.198 10 false V13 4.323,1.01 4.781,1.208 0.458,0.198 10 false V13 2.823,0.448 3.281,0.646 0.458,0.198 10 false V24 2.823,1.01 3.281,1.208 0.458,0.198 10 false V24 2.813,1.521 3.271,1.719 0.458,0.198 10 false V23 2.813,2.073 3.271,2.271 0.458,0.198 10 false V23 2.823,2.635 3.281,2.833 0.458,0.198 10 false V23 2.823,3.208 3.281,3.406 0.458,0.198 10 false V23 2.823,3.771 3.281,3.969 0.458,0.198 10 false V23 0.688,0.688 3.75,0.885 3.063,0.198 10 false Back Door Lock Motor 0.906,1.667 3.969,1.865 3.063,0.198 10 false Half Latch Switch 1.083,2.24 4.146,2.438 3.063,0.198 10 false Initial Switch 1.083,2.771 4.146,2.969 3.063,0.198 10 false Pawl Switch 0.635,3.344 3.698,3.542 3.063,0.198 10 false Back Door Courtesy Switch 2.438,0.573 2.75,0.771 0.313,0.198 10 false M+ 2.448,1.146 2.76,1.344 0.313,0.198 10 false M- 2.396,1.646 2.854,1.844 0.458,0.198 10 false CLS 2.385,2.208 2.844,2.406 0.458,0.198 10 false OPN 2.375,2.76 2.833,2.958 0.458,0.198 10 false FSW 2.406,3.344 2.865,3.542 0.458,0.198 10 false CTY 2.521,3.885 2.677,4.083 0.156,0.198 10 false E 4.708,0.583 5.167,0.781 0.458,0.198 10 false DC+ 4.729,1.146 5.188,1.344 0.458,0.198 10 false DC- 4.729,3.344 5.188,3.542 0.458,0.198 10 false FUL 6.521,1.948 6.979,2.146 0.458,0.198 10 false CPU 2.896,0.823 3.052,1.021 0.156,0.198 10 false 1 2.896,0.25 3.052,0.448 0.156,0.198 10 false 2 4.365,0.25 4.677,0.448 0.313,0.198 10 false 10 4.417,0.792 4.573,0.99 0.156,0.198 10 false 9 4.708,1.646 5.167,1.844 0.458,0.198 10 false HAF 4.375,1.302 4.688,1.5 0.313,0.198 10 false 24 4.719,2.219 5.177,2.417 0.458,0.198 10 false POS 4.708,2.792 5.167,2.99 0.458,0.198 10 false PAWL 2.906,1.302 3.063,1.5 0.156,0.198 10 false 3 2.896,2.417 3.052,2.615 0.156,0.198 10 false 2 2.896,1.844 3.052,2.042 0.156,0.198 10 false 6 2.917,3.552 3.073,3.75 0.156,0.198 10 false 1 2.917,2.979 3.073,3.177 0.156,0.198 10 false 4 5.177,0.5 5.875,0.854 0.698,0.354 10 false Motor Drive Circuit 4.375,1.865 4.688,2.063 0.313,0.198 10 false 21 4.417,2.406 4.573,2.604 0.156,0.198 10 false 6 4.396,2.979 4.708,3.177 0.313,0.198 10 false 20 5.281,2.281 6.042,2.646 0.76,0.365 10 false Switch Input Circuit

w/o Power Back Door
B411291E05
0.521,4.177 4.042,4.375 3.521,0.198 10 false Back Door Lock Assembly 4.938,4.271 7.156,4.521 2.219,0.25 10 false Multiplex Network Door ECU 4.344,1.531 4.802,1.729 0.458,0.198 10 false V25 4.333,2.073 4.792,2.271 0.458,0.198 10 false V25 4.344,2.635 4.802,2.833 0.458,0.198 10 false V25 4.323,3.198 4.781,3.396 0.458,0.198 10 false V25 4.333,0.448 4.792,0.646 0.458,0.198 10 false V26 4.323,1.01 4.781,1.208 0.458,0.198 10 false V26 2.823,0.448 3.281,0.646 0.458,0.198 10 false V24 2.823,1.01 3.281,1.208 0.458,0.198 10 false V24 2.813,1.521 3.271,1.719 0.458,0.198 10 false V23 2.813,2.073 3.271,2.271 0.458,0.198 10 false V23 2.823,2.635 3.281,2.833 0.458,0.198 10 false V23 2.823,3.208 3.281,3.406 0.458,0.198 10 false V23 2.823,3.771 3.281,3.969 0.458,0.198 10 false V23 0.688,0.688 3.75,0.885 3.063,0.198 10 false Back Door Lock Motor 0.906,1.667 3.969,1.865 3.063,0.198 10 false Half Latch Switch 1.083,2.24 4.146,2.438 3.063,0.198 10 false Initial Switch 1.083,2.771 4.146,2.969 3.063,0.198 10 false Pawl Switch 0.635,3.344 3.698,3.542 3.063,0.198 10 false Back Door Courtesy Switch 2.438,0.573 2.75,0.771 0.313,0.198 10 false M+ 2.448,1.146 2.76,1.344 0.313,0.198 10 false M- 2.396,1.646 2.854,1.844 0.458,0.198 10 false CLS 2.385,2.208 2.844,2.406 0.458,0.198 10 false OPN 2.375,2.76 2.833,2.958 0.458,0.198 10 false FSW 2.406,3.344 2.865,3.542 0.458,0.198 10 false CTY 2.521,3.885 2.677,4.083 0.156,0.198 10 false E 4.708,0.583 5.167,0.781 0.458,0.198 10 false DC+ 4.729,1.146 5.188,1.344 0.458,0.198 10 false DC- 4.729,3.344 5.188,3.542 0.458,0.198 10 false FUL 6.521,1.948 6.979,2.146 0.458,0.198 10 false CPU 2.896,0.823 3.052,1.021 0.156,0.198 10 false 1 2.896,0.271 3.052,0.469 0.156,0.198 10 false 2 4.365,0.25 4.677,0.448 0.313,0.198 10 false 10 4.417,0.792 4.573,0.99 0.156,0.198 10 false 9 4.708,1.646 5.167,1.844 0.458,0.198 10 false HAF 4.375,1.302 4.688,1.5 0.313,0.198 10 false 24 4.719,2.219 5.177,2.417 0.458,0.198 10 false POS 4.708,2.792 5.167,2.99 0.458,0.198 10 false PAWL 2.906,1.302 3.063,1.5 0.156,0.198 10 false 3 2.896,2.417 3.052,2.615 0.156,0.198 10 false 2 2.896,1.844 3.052,2.042 0.156,0.198 10 false 6 2.917,3.552 3.073,3.75 0.156,0.198 10 false 1 2.917,2.979 3.073,3.177 0.156,0.198 10 false 4 5.177,0.5 5.875,0.854 0.698,0.354 10 false Motor Drive Circuit 4.375,1.865 4.688,2.063 0.313,0.198 10 false 21 4.417,2.406 4.573,2.604 0.156,0.198 10 false 6 4.396,2.979 4.708,3.177 0.313,0.198 10 false 20 5.281,2.281 6.042,2.646 0.76,0.365 10 false Switch Input Circuit

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system*.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

*: w/ Power Back Door System



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Closer Position SW Initial switch signal ON or OFF ON: Back door lock center gear in center position (initial switch on)
OFF: Back door lock center gear not in center position (initial switch off)
*: Refer to "CONSTRUCTION AND OPERATION"

*: Refer to "CONSTRUCTION AND OPERATION"

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>SYSTEM DESCRIPTION

Body Electrical > Back Door > Data List
Tester Display
Closer Position SW
50003 159 3
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT BACK DOOR LOCK ASSEMBLY
2.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

w/ Power Back Door System:

i.

Disconnect the V23 back door lock assembly connector.


ii.

Disconnect the V12 multiplex network door ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V23-6 (OPN) - V12-21 (POS) Always Below 1 Ω
V23-1 (E) - Body ground Always Below 1 Ω
V23-6 (OPN) or V12-21 (POS) - Body ground Always 10 kΩ or higher




b.

w/o Power Back Door System:

i.

Disconnect the V23 back door lock assembly connector.


ii.

Disconnect the V25 multiplex network door ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V23-6 (OPN) - V25-21 (POS) Always Below 1 Ω
V23-1 (E) - Body ground Always Below 1 Ω
V23-6 (OPN) or V25-21 (POS) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR