Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High Stop light switch remains on even when the vehicle is driven in a stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) pattern 5 times (2-trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during stop and go driving, the TCM interprets this as a fault in the stop light switch. Then the MIL illuminates and the TCM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) 5 times for 2 driving cycles in order for the DTC to be stored.

WIRING DIAGRAM

C347416E02
1.531,2.396 2.115,2.615 0.583,0.219 10 false Battery 1.563,1.563 2.125,1.927 0.563,0.365 10 false FL MAIN 3.0W 2.49,1.552 2.948,1.75 0.458,0.198 10 false ALT 3.208,1.552 3.656,1.75 0.448,0.198 10 false STOP 3.823,1.719 4.281,1.917 0.458,0.198 10 false A64 3.833,1.906 4.927,2.281 1.094,0.375 10 false Stop Light Switch Assembly 3.938,1.5 4.094,1.698 0.156,0.198 10 false 7 4.729,1.49 4.885,1.688 0.156,0.198 10 false 3 5.219,1.5 5.458,1.708 0.24,0.208 10 false 14 4.531,1.365 4.688,1.563 0.156,0.198 10 false L 4.135,1.365 4.292,1.563 0.156,0.198 10 false B 5.49,1.26 5.948,1.458 0.458,0.198 10 false STP 5.833,2.885 6.448,3.083 0.615,0.198 10 false G147 5.875,3.073 6.333,3.271 0.458,0.198 10 false TCM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Repeat below procedure for 5 times:*1

·

Stop the vehicle (vehicle speed is 3 km/h (2 mph) or less)

·

Drive the vehicle (vehicle speed is 30 km/h (19 mph) or more)


2.

Turn the ignition switch off.

3.

Perform step (*1) again.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
Powertrain > ECT > Data List
Tester Display
Stop Light Switch
50003 235 188


PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

Stop light switch assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

NG

SECURELY INSTALL OR REPLACE STOP LIGHT SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
a.

Disconnect the A64 stop light switch assembly connector.


b.

Disconnect the G147 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-3 (L) - G147-14 (STP) Brake pedal depressed Below 1 Ω
A64-3 (L) or G147-14 (STP) - Body ground Brake pedal released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY