The TCM uses the signals from the throttle position sensor, air-flow meter, transmission revolution sensor (NT), transmission revolution sensor (SP2) and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.
Then the TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect mechanical problems of shift solenoid valve SLU, the valve body and torque converter assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2757 | Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) | Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range (2-trip detection logic). | ·
Shift solenoid valve SLU remains open or closed ·
Valve body is blocked ·
Torque converter assembly ·
Automatic transmission (clutch, brake, gear, etc.) ·
Line pressure is too low |
- | DTC stored |
Torque converter assembly lock-up is controlled by the TCM based on the input turbine speed (NT), output shaft speed (SP2), engine speed, engine load, engine temperature, vehicle speed, transmission temperature and gear selection. The TCM determines the lock-up status of the torque converter assembly by comparing the engine speed (NE) to the input turbine speed (NT). The TCM calculates the actual transmission gear by comparing the input turbine speed (NT) to the output shaft speed (SP2). When conditions are appropriate, the TCM requests lock-up by applying control voltage to shift solenoid SLU. When shift solenoid valve SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter assembly.
If the TCM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the TCM interprets this as a fault in shift solenoid valve SLU or the lock-up system performance.
The TCM will store the DTC.
Example:
When any of the following is met, the system judges it as a malfunction.
There is a difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up. (Engine speed is at least 70 rpm more than the input turbine speed.)
There is no difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up off. (The difference between engine speed and input turbine speed is less than 35 rpm.)
Perform registration and/or initialization when parts related to the automatic transmission are replaced.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the Lock-up Function in Road Test.*1
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST
Turn the ignition switch off.
Perform step (*1) again.
Check for DTCs again.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Lock Up | Control shift solenoid valve SLU to set automatic transmission to lock-up | ON or OFF | Possible to check shift solenoid valve SLU operation.
[Vehicle Condition] ·
Throttle valve opening angle: Less than 35% ·
Vehicle speed: 80 km/h (50 mph) or more |
| Tester Display |
|---|
| Activate the Lock Up |
This test can be conducted when the vehicle speed is 80 km/h (50 mph) or more.
This test can be conducted with the 5th gear.
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal.
(Fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically.)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Only P2757 is output | A |
| P2757 and other DTCs are output | B |
If any other codes besides P2757 are output, perform troubleshooting for those DTCs first.
A
B
| *a | Component without harness connected
(Shift Solenoid Valve SLU) |
Remove shift solenoid valve SLU.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the torque converter assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL
NG
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL