The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.
| *a | Object Exceeding Weight Limit of Transmission Jack |
The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
Wear protective gloves when removing the exhaust pipe assembly.
The exhaust pipe assembly is extremely hot immediately after the engine has stopped.
Confirm that the exhaust pipe assembly has cooled down before removing it.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
41110F
3.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY
4.DRAIN AUTOMATIC TRANSMISSION FLUID
5.DRAIN TRANSFER OIL
37100
6.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>REMOVAL
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>REMOVAL
28100
7.REMOVE STARTER ASSEMBLY
for 2.0 kW Type:
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL
for BOSCH Made:
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
17410
8.REMOVE FRONT EXHAUST PIPE ASSEMBLY
33820B
9.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the nut and clip and disconnect the transmission control cable assembly.
10.DISCONNECT OIL COOLER TUBE
Using a union nut wrench, disconnect the outlet oil cooler tube and inlet oil cooler tube.
Use a container to catch any ATF which flows out of the 2 oil cooler tubes and automatic transmission assembly.
Remove the 3 bolts and 3 oil cooler tube clamps.
Remove the 4 bolts and 3 oil cooler tube clamps from the automatic transmission assembly and engine assembly.
It is not necessary to remove the oil cooler clamp they are being replaced.
33823
11.REMOVE TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and transmission control cable bracket from the automatic transmission assembly.
82284
12.DISCONNECT GROUND WIRE
Remove the bolt and disconnect ground wire from the transfer assembly.
13.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
Support the automatic transmission assembly with a transmission jack.
In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.
Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.
To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.
Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.
33118B
14.REMOVE STIFFENER PLATE
| *a | LH Side |
| *b | RH Side |
Remove the 4 bolts and stiffener plate RH (with oil cooler tube clamp).
Remove the 4 bolts and stiffener plate LH.
Remove the No. 4 cylinder block insulator.
Remove the No. 2 end plate.
15.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley set bolt with a wrench.
51204
16.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Remove the 4 bolts and disconnect the No. 3 frame crossmember sub-assembly from the rear engine mounting insulator.
Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.
12371A
17.REMOVE REAR ENGINE MOUNTING INSULATOR
Remove the 4 bolts and rear engine mounting insulator from the automatic transmission assembly.
82121
18.DISCONNECT ENGINE WIRE
Tilt the automatic transmission assembly downward.
Make sure that the cooling fan and fan shroud do not contact the engine when tilting the automatic transmission assembly.
Detach the 5 clamps and disconnect the transfer breather hose sub-assembly from the automatic transmission assembly.
| *a | Transmission Wire Connector |
Disconnect the 5 connectors.
Detach the claw and press down the lever to disconnect engine wire from the transmission wire connector.
Remove the bolt, detach the 7 wire harness clamps and disconnect the engine wire from the automatic transmission assembly and transfer assembly.
19.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
Remove the 5 bolts.
Remove the automatic transmission assembly.
Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.
Do not use excess force to pry on the automatic transmission assembly.
36100
20.REMOVE TRANSFER ASSEMBLY
21.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 3 bolts and 3 wire harness clamp brackets.
36478A
22.REMOVE TRANSMISSION BREATHER BRACKET
Detach the clamp to disconnect the automatic transmission breather hose from the transfer breather bracket.
Remove the bolt and transmission breather bracket.
32000
23.REMOVE TORQUE CONVERTER ASSEMBLY
| *a | Matchmark |
Put matchmarks on the automatic transmission assembly and the torque converter assembly.
Remove the torque converter assembly from the automatic transmission assembly.
Remove the torque converter assembly from the input shaft horizontally.
32000
24.INSPECT TORQUE CONVERTER ASSEMBLY
25.INSPECT DRIVE PLATE