Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The ECM communicates with the TCM using the Controller Area Network (CAN).

If there is a problem with this communication, the TCM stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0100 Lost Communication with ECM / PCM "A" All conditions are met for 1.25 seconds (1-trip detection logic):
·

Ignition switch is ON.

·

Battery voltage is 10.5 V or higher.

·

There is no communication between the ECM and TCM.


·

Harness or connector

·

ECM

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C331554E05
0.802,3.427 4.469,3.625 3.667,0.198 10 false : CAN Communication Line 5.74,0.615 6.354,0.813 0.615,0.198 10 false CAN+ 0.979,0.615 1.594,0.813 0.615,0.198 10 false CAN+ 1,1.156 1.615,1.354 0.615,0.198 10 false CAN- 5.75,1.167 6.365,1.365 0.615,0.198 10 false CAN- 6.031,2.938 6.646,3.135 0.615,0.198 10 false TCM 5.99,2.76 6.625,2.958 0.635,0.198 10 false G147 0.75,2.76 1.365,2.958 0.615,0.198 10 false ECM 1.156,1.698 1.771,1.896 0.615,0.198 10 false +B 1.177,2.24 1.792,2.438 0.615,0.198 10 false E1 1.417,0.604 2.031,0.802 0.615,0.198 10 false G140 1.417,1.146 2.031,1.344 0.615,0.198 10 false G140 1.417,1.688 2.031,1.885 0.615,0.198 10 false G141 1.417,2.229 2.031,2.427 0.615,0.198 10 false C115 1.51,0.396 2.125,0.594 0.615,0.198 10 false 22 1.5,0.938 2.115,1.135 0.615,0.198 10 false 21 1.542,1.479 2.156,1.677 0.615,0.198 10 false 1 1.552,2.01 2.167,2.208 0.615,0.198 10 false 7 5.479,0.813 6.094,1.01 0.615,0.198 10 false 21 5.469,1.344 6.083,1.542 0.615,0.198 10 false 20 3.021,1.698 6.688,1.896 3.667,0.198 10 false from EFI-MAIN NO. 1 Relay

CAUTION / NOTICE / HINT

HINT:
·

Refer to the inspection procedure for the CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.

·

The malfunctioning area can be confirmed using the Bus Check function of the GTS.

for LHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM

for RHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Check that the battery voltage is 10.5 V or higher.

2.

Turn the ignition switch to ON.




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
C331377C03
2.635,0.229 3.063,0.49 0.427,0.26 2.948,2.896 3.177,1.667 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.729,2.969 3.292,3.177 0.563,0.208 10 false 1 (+B) 2.677,0.271 3.24,0.479 0.563,0.208 10 false G141
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C331378C03
1.115,0.25 1.531,0.49 0.417,0.24 0.813,2.792 1.031,1.667 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.156,0.271 1.656,0.479 0.5,0.208 10 false C115 0.635,2.865 1.219,3.073 0.583,0.208 10 false 7 (E1)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-7 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the G140 ECM connector.


b.

Disconnect the G147 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G140-22 (CAN+) - G147-21 (CAN+) Always Below 1 Ω
G140-21 (CAN-) - G147-20 (CAN-) Always Below 1 Ω
G140-22 (CAN+) or G147-21 (CAN+) - Body ground or other terminals Always 10 kΩ or higher
G140-21 (CAN-) or G147-20 (CAN-) - Body ground or other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR

Powertrain > ECT > Clear DTCs
50002 235

e.

Start the engine.


f.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

g.

Read the DTCs using the GTS.

Result:
Result Proceed to
DTCs are not output A
U0100 is output B




A

END

B