Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › CAMSHAFT › from 2016.01
RM3270E _51 Engine / Hybrid System _048923 2GD-FTV ENGINE MECHANICAL _0242425 CAMSHAFT A

2GD-FTV ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1.INSTALL CAMSHAFT

a.
A346673C01
1.573,0.594 0.99,0.344 0.99,0.344 0.74,0.344 true 0.938,0.979 0.51,1.125 0.51,1.125 0.344,1.125 true 2.656,1.573 3.073,1.573 true 0.573,0.25 0.781,0.406 0.208,0.156 10 false *1 0.177,1.021 0.427,1.177 0.25,0.156 10 false *2 3.094,1.469 3.323,1.625 0.229,0.156 10 false *3
*1 Valve Rocker Arm Sub-assembly
*2 Valve Stem Cap
*3 Valve Lash adjuster assembly


Check that the valve rocker arm sub-assembly is firmly set to the valve lash adjuster assembly.


b.

Apply a light coat of engine oil to the camshaft journals of the cylinder head sub-assembly and the thrust portion of the camshaft.


c.
A346674C01
1.677,0.156 1.865,0.156 1.865,0.156 2.26,0.333 true 2.302,0.458 2.896,0.573 2.896,0.573 3.031,0.573 true 1.5,0.063 1.729,0.25 0.229,0.188 10 false *a 3.063,0.49 3.292,0.677 0.229,0.188 10 false *b
*a Paint Mark
*b Timing Mark


Align the paint mark of the No. 2 chain sub-assembly and timing mark of the camshaft timing sprocket, and install the camshaft timing sprocket to the No. 2 chain sub-assembly.

HINT:

Make sure the timing mark of the camshaft timing sprocket face the front side.



d.
A349446

Align the knock pin of the No. 1 camshaft to the groove of the sprocket and install the No. 1 camshaft to the camshaft timing sprocket, and set the bolt.


e.
A346675C01
1.323,0.396 1.583,0.135 1.583,0.135 1.76,0.135 true 1.313,0.5 0.552,0.219 0.552,0.219 0.354,0.219 true 1.771,0.042 2.021,0.208 0.25,0.167 10 false *a 0.167,0.125 0.365,0.292 0.198,0.167 10 false *b
*a Paint Mark
*b Timing Mark


Align the paint mark of the No. 2 chain sub-assembly and timing mark of the camshaft timing sprocket, and install the camshaft timing sprocket to the No. 2 chain sub-assembly.

HINT:

Make sure the timing mark of the camshaft timing sprocket face the front side.



f.
A349447

Align the knock pin of the No. 2 camshaft to the groove of the sprocket and install the No. 2 camshaft to the camshaft timing sprocket, and set the bolt.

HINT:
A344474C01
0.667,1.583 0.729,1.854 0.729,1.854 0.813,1.854 true 0.667,1.146 0.719,0.885 0.719,0.885 0.802,0.885 true 0.833,1.75 1.146,1.948 0.313,0.198 10 false *a 0.823,0.792 1.135,0.99 0.313,0.198 10 false *a
*a Groove


Groove is at the rear end of the No. 2 camshaft.



g.
A344473C01
1.021,0.771 0.625,0.375 0.625,0.375 0.458,0.375 true 2.396,0.781 2.729,0.427 2.729,0.427 2.896,0.427 true 2.406,0.917 2.385,1.594 true 1.021,0.917 1.021,1.583 true 0.292,0.271 0.5,0.438 0.208,0.167 10 false *a 0.958,1.594 1.188,1.76 0.229,0.167 10 true *b 2.927,0.313 3.135,0.479 0.208,0.167 10 false *a 2.333,1.604 2.563,1.771 0.229,0.167 10 true *b
*a Paint Mark
*b Timing Mark


Check the timing mark of the camshaft timing sprocket and paint mark of the No. 2 chain sub-assembly.


h.
A344475

Set the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps to the cylinder head sub-assembly as shown in the illustration.


i.

Temporarily install the 20 bolts.


j.
A344476C01
1.75,0.531 1.896,0.708 0.146,0.177 10 true 4 1.75,0.885 1.896,1.063 0.146,0.177 10 true 3 1.75,1.458 1.896,1.635 0.146,0.177 10 true 2 1.75,1.115 1.896,1.292 0.146,0.177 10 true 1 2.406,1.115 2.552,1.292 0.146,0.177 10 true 5 2.406,1.458 2.552,1.635 0.146,0.177 10 true 6 2.385,0.531 2.531,0.708 0.146,0.177 10 true 8 2.406,0.906 2.552,1.083 0.146,0.177 10 true 7 1.104,1.458 1.333,1.635 0.229,0.177 10 true 10 1.104,1.125 1.25,1.302 0.146,0.177 10 true 9 1.104,0.896 1.333,1.073 0.229,0.177 10 true 11 1.115,0.531 1.344,0.708 0.229,0.177 10 true 12 3.031,1.104 3.26,1.281 0.229,0.177 10 true 13 3.031,1.458 3.26,1.635 0.229,0.177 10 true 14 3.031,0.906 3.26,1.083 0.229,0.177 10 true 15 3.052,0.531 3.281,0.708 0.229,0.177 10 true 16 0.583,1.417 0.781,1.594 0.198,0.177 10 true 17 0.583,0.615 0.771,0.792 0.188,0.177 10 true 18 0.583,1.729 0.771,1.917 0.188,0.188 10 true 19 0.573,0.281 0.771,0.458 0.198,0.177 10 true 20
V100135

Bolt A
V100136

Bolt B


Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 21 N*m (214 kgf*cm, 15 ft.*lbf)


k.
A346684C01
1.917,0.667 2.896,0.667 true 0.573,2.969 1.427,2.969 true 2.927,0.563 3.167,0.75 0.24,0.188 10 false *1 0.375,2.865 0.615,3.052 0.24,0.188 10 false *2
*1 No. 1 Camshaft
*2 No. 2 Camshaft


Hold the hexagonal portion of the No. 1 camshaft and No. 2 camshaft with a wrench, and tighten the 2 bolts.

Torque:
81 N*m (826 kgf*cm, 60 ft.*lbf)

NOTICE:

Be careful not to damage the cylinder head sub-assembly with the wrench.



l.

Remove the pin from the No. 2 chain tensioner assembly.


m.

Install a new gasket and the oil pump relief valve plug to the timing chain cover.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 13566B 2.INSTALL TIMING CHAIN GUIDE

a.

Install the timing chain guide to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11382C 3.INSTALL CAMSHAFT OIL SEAL RETAINER

Hide 29300 4.TEMPORARILY INSTALL VACUUM PUMP ASSEMBLY

Hide 5.INSTALL NO. 3 CAMSHAFT BEARING CAP

a.

Clean and degrease the contact surfaces of the cylinder head sub-assembly and No. 3 camshaft bearing cap.


b.
A346676C01
0.667,1.417 0.417,1.417 false 3.01,1.417 2.76,1.417 false 0.25,1.302 0.458,1.458 0.208,0.156 10 false *a 3.021,1.313 3.229,1.469 0.208,0.156 10 false *a
*a Seal Packing


Apply seal packing to the specified areas as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 mm (0.118 in.)


NOTICE:
·

Do not allow seal packing to contact the oil passage of the No. 3 camshaft bearing cap.

·

After applying seal packing, install the No. 3 camshaft bearing cap within 3 minutes and tighten the bolts within 10 minutes.

·

Do not start the engine for at least 2 hours after installation.




c.

Install the No. 3 camshaft bearing cap with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Wipe off excess seal packing from between No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 29300 6.INSTALL VACUUM PUMP ASSEMBLY

Hide 11201 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23682 8.INSTALL NOZZLE HOLDER GASKET

Hide 23670 9.TEMPORARILY INSTALL INJECTOR ASSEMBLY

Hide 10.TEMPORARILY INSTALL NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 11.TIGHTEN INJECTOR ASSEMBLY

Hide 12.TIGHTEN NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23760 13.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 15.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 16.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 25601 18.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 16209 19.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16206B 20.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25625 22.INSTALL EGR VALVE BRACKET

Hide 23300 24.CONNECT FUEL FILTER ASSEMBLY

Hide 12632 25.INSTALL NO. 2 ENGINE COVER BRACKET

Hide 44763C 26.INSTALL NO. 2 HOSE TO HOSE TUBE

Hide 89421C 27.INSTALL TURBO PRESSURE SENSOR

Hide 16278 29.INSTALL NO. 2 WATER BY-PASS PIPE

Hide 26100G 30.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 16400 32.INSTALL RADIATOR ASSEMBLY

Hide 16572D 33.CONNECT NO. 2 RADIATOR HOSE

Hide 16711 34.INSTALL FAN SHROUD

Hide 32941 35.CONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 32942 36.CONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 16470 37.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Hide 44369A 38.INSTALL NO. 1 OIL RESERVOIR BRACKET

Hide 44360 39.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 16571C 40.INSTALL NO. 1 RADIATOR HOSE

Hide 17362B 41.INSTALL NO. 2 AIR TUBE

Hide 17344E 42.INSTALL NO. 4 AIR HOSE

Hide 16593 43.INSTALL NO. 1 RADIATOR AIR GUIDE

Hide 12601B 44.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 51410 46.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 47.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION