Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0217064 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C237478N04
1.385,1.313 0.75,0.854 0.75,0.854 0.563,0.854 true 0.219,0.792 0.719,1.188 0.5,0.396 10 false SST

Using SST and a dial indicator, measure the differential ring gear backlash.

SST
09564-33010  

Standard Backlash:

0.11 to 0.21 mm (0.00433 to 0.00826 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the differential ring gear.




Hide 41204D 2.INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C236648C05
2.479,1.813 2.656,1.969 0.177,0.156 10 false *a
*a 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the front drive pinion companion flange vertically and laterally.

Maximum Runout:
Item Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the front drive pinion companion flange.



Hide 89429 3.REMOVE OIL TEMPERATURE SENSOR

a.
C326232

Remove the oil temperature sensor from the front differential carrier assembly.


Hide 41400B 4.REMOVE DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY (w/ A.D.D.)

a.
C327526

Remove the 4 bolts.


b.
C327527

Using a hammer, pry out the differential motor actuator assembly from the front differential tube assembly.


Hide 41320 5.REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY

a.
C237653

Using an E14 ''TORX'' socket wrench, remove the 4 bolts.


b.

Using a plastic-faced hammer, tap out the front differential tube assembly.


Hide 41304P 6.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH

a.
C328236N01
1.021,1.677 1.021,1.156 false 0.896,1.729 1.354,1.927 0.458,0.198 10 false SST

Using SST, tap out the differential side gear shaft oil seal LH.

SST
09308-00010  


Hide 41433 7.REMOVE DIFFERENTIAL CLUTCH SLEEVE (w/ A.D.D.)

a.

Remove the differential clutch sleeve.


Hide 41306F 8.REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY (w/ A.D.D.)

a.

Remove the side gear intermediate shaft hole snap ring from the differential side gear inter shaft sub-assembly.


b.
C282342C02
0.729,0.417 1.219,0.417 1.219,0.417 1.219,0.729 false 0.438,0.323 0.896,0.521 0.458,0.198 10 false SST 3.042,0.271 3.323,0.521 0.281,0.25 10 false *a 0.146,1.406 0.427,1.656 0.281,0.25 10 false *b
*a Turn
*b Hold


Using SST, remove the differential side gear inter shaft sub-assembly.

SST
09350-20015  (09369-20040)
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)


Hide 41183B 9.REMOVE FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR (w/ A.D.D.)

a.
C237481C04
1.333,0.969 1.333,0.375 1.333,0.375 0.802,0.375 false 0.615,0.281 0.885,0.458 0.271,0.177 10 false *a
*a Protective Tape


Using a screwdriver, pry out the front differential side bearing retainer deflector.

HINT:

Tape the screwdriver tip before use.



Hide 41204D 10.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

Hide 41204D 11.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41201C 12.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

Hide 41214C 13.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41211B 14.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326642N01
2.5,0.563 2.5,0.229 2.5,0.229 2.781,0.229 false 2.844,0.156 3.219,0.365 0.375,0.208 10 false SST

Using SST, remove the front drive pinion rear tapered roller bearing (inner) from the differential drive pinion.

SST
09556-22010  


Hide 15.REMOVE DIFFERENTIAL SIDE BEARING RETAINER

a.

Remove the 10 bolts and tap out the differential side bearing retainer with a plastic-faced hammer.


Hide 16.REMOVE DIFFERENTIAL CASE ASSEMBLY

Hide 17.REMOVE DIFFERENTIAL DRIVE PINION

Hide 41231F 18.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41211A 19.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C313100N01
0.781,2.823 0.781,2.385 0.781,2.385 0.615,2.385 false 0.708,0.5 1.104,0.5 1.104,0.5 1.75,1.01 true 0.344,2.333 0.802,2.531 0.458,0.198 10 false SST 0.406,0.438 0.865,0.635 0.458,0.198 10 false SST

Using SST and a press, press out the front drive pinion front tapered roller bearing (inner) and drive pinion plate washer from the differential drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the differential drive pinion.


HINT:

If the differential drive pinion or differential ring gear is damaged, replace them as a set.



Hide 41211B 20.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C282337C02
2.281,1.365 2.5,1.365 2.5,1.365 2.5,1.521 false 2.26,1.521 2.698,1.521 false 1.156,0.146 1.469,0.344 0.313,0.198 10 false *a 2.76,0.865 3.073,1.063 0.313,0.198 10 false *b 2.771,1.417 3.083,1.615 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the front drive pinion rear tapered roller bearing (outer).

SST
09502-12010  
09612-65014  (09612-01020, 09612-01050)


Hide 41115F 21.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING

a.

Using a brass bar and hammer, tap out the front differential oil storage ring.


Hide 41211A 22.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237483

Using a brass bar and hammer, tap out the front drive pinion front tapered roller bearing (outer).


Hide 41311A 23.REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
·

Measure the thickness of the case washer.

·

Tag the bearing outer races so that they can be reinstalled in the correct locations.



a.
C237485N02
0.948,0.552 0.427,0.552 false 0.802,1.042 0.563,1.042 0.563,1.042 0.563,0.552 true 0.094,0.5 0.604,0.802 0.51,0.302 10 false SST

Using SST and a press, press out the front differential case bearing (outer) and plate washer from the differential side bearing retainer.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

If the bearing is damaged during removal, replace it.



b.
C237486N02
1.208,0.49 0.521,0.49 false 1.135,0.927 0.792,0.927 0.792,0.927 0.792,0.49 true 0.208,0.438 0.604,0.677 0.396,0.24 10 false SST

Using SST and a press, press out the front differential case bearing (outer) and plate washer from the differential carrier.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

If the bearing is damaged during removal, replace it.



Hide 24.REMOVE DIFFERENTIAL RING GEAR

a.
C331344C01
1.938,1.167 2.76,1.167 false 1.896,1.042 2.5,1.042 2.5,1.042 2.5,1.167 false 2.813,1.083 3.125,1.281 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the differential ring gear and differential case.


b.

Remove the 10 differential ring gear set bolts.


c.
C236664

Using a plastic-faced hammer, tap on the differential ring gear to separate it from the differential case assembly.


Hide 41311A 25.REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:

The differential case and case bearings should only be removed when replacement is necessary.


a.
C282338C02
0.781,0.479 1.135,0.479 1.135,0.479 1.135,0.76 false 2.781,1.542 2.781,2.083 2.781,2.083 3.031,2.083 true 0.458,0.396 0.917,0.594 0.458,0.198 10 false SST 3.073,1.958 3.281,2.177 0.208,0.219 10 false *a 2.625,0.24 2.833,0.458 0.208,0.219 10 false *b 0.219,1.292 0.427,1.51 0.208,0.219 10 false *c
*a Notch
*b Turn
*c Hold


Using SST, remove the 2 front differential case bearings (inner) from the differential case.

SST
09950-60010  (09951-00480)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09953-04020, 09958-04011)

HINT:

Attach the claws of SST to the notch in the differential case assembly to secure SST.



Hide 26. DISASSEMBLE DIFFERENTIAL CASE

a.
C236667

Using a chisel and hammer, unstake the differential case.


b.
C238726

Using a pin punch and hammer, tap out the straight pin.


c.
C236669

Remove the following parts from the differential case.

1.
C236670C03
0.563,0.542 0.563,0.219 0.563,0.219 0.396,0.219 false 0.906,0.635 0.906,0.167 0.906,0.167 0.979,0.167 false 1.635,1.052 1.635,0.5 1.635,0.5 1.49,0.5 false 2.063,0.479 2.063,0.125 2.063,0.125 1.958,0.125 false 2.75,0.51 3,0.51 false 2.375,1.604 2.375,1.854 false 2.75,1.688 2.75,1.833 false 0.552,1.458 0.552,1.177 0.552,1.177 0.427,1.177 false 1.146,1.708 1.146,1.896 1.146,1.896 1.292,1.896 false 1.042,0.083 1.25,0.25 0.208,0.167 10 false *1 0.198,0.146 0.406,0.313 0.208,0.167 10 false *2 1.281,0.427 1.49,0.594 0.208,0.167 10 false *3 1.76,0.052 1.969,0.219 0.208,0.167 10 false *4 3.052,0.427 3.26,0.594 0.208,0.167 10 false *5 2.313,1.906 2.521,2.073 0.208,0.167 10 false *1 2.708,1.885 2.917,2.052 0.208,0.167 10 false *2 1.365,1.813 1.573,1.979 0.208,0.167 10 false *4 0.229,1.115 0.438,1.281 0.208,0.167 10 false *5
*1 Differential Pinion Gear
*2 Differential Pinion Gear Thrust Washer
*3 Differential Pinion Shaft
*4 Differential Side Gear
*5 Differential Side Gear Thrust Washer


Differential pinion gear (2 pieces)

2.

Differential pinion gear thrust washer (2 pieces)

3.

Differential pinion shaft

4.

Differential side gear (2 pieces)

5.

Differential side gear thrust washer (2 pieces)



Hide 41039A 27.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential side gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.



Hide 41311 28.INSPECT FRONT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.



Hide 41331G 29.REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING

a.
C237523

Using a brass bar and hammer, tap out the 2 front differential side gear needle roller bearings.


Hide 41434 30.REMOVE DIFFERENTIAL CLUTCH HUB (w/ A.D.D.)

a.
C237524

Using a snap ring expander, remove the side gear shaft hole snap ring.


b.

Remove the differential clutch hub.


Hide 41304P 31.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH

a.
C328238N01
0.99,1.021 0.99,0.469 0.99,0.469 0.729,0.469 false 0.406,0.396 0.865,0.594 0.458,0.198 10 false SST

Using SST, tap out the differential side gear shaft oil seal RH from the front differential tube assembly.

SST
09308-00010  


Hide 41304F 32.REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C237490

Using a snap ring pliers, remove the snap ring.


b.

Remove the differential side gear shaft sub-assembly RH from the front differential tube assembly.


Hide 41304L 33.REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH

a.

Using a snap ring expander, remove the snap ring.


b.
C328243N01
2.344,0.656 2.635,0.375 2.635,0.375 2.802,0.375 false 2.885,0.292 3.344,0.49 0.458,0.198 10 false SST

Using SST, a brass bar and a press, press out the front differential side gear shaft bearing RH.

SST
09950-00020  

NOTICE:
·

Do not damage the front differential side gear shaft bearing RH.

·

Do not drop the differential side gear shaft sub-assembly RH.




Hide 34.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB (w/ A.D.D.)

a.
C237525

Check that there is no wear or damage on the differential clutch hub and differential clutch sleeve.

If necessary, replace them.



b.

Check that the differential clutch sleeve slides smoothly on the differential clutch hub.


Hide 35.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT (w/ A.D.D.)

a.
C237646

Check that there is no wear or damage on the differential clutch sleeve and differential side gear inter shaft.

If necessary, replace differential clutch sleeve and differential side gear inter shaft.


b.

Check that the differential clutch sleeve slides smoothly on the differential side gear inter shaft.


Hide 36.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE (w/ A.D.D.)

a.
C237647

Using a feeler gauge, measure the clearance between the clutch sleeve fork and differential clutch sleeve.

Maximum clearance:

0.35 mm (0.0138 in.)


If the clearance is more than the maximum, replace the clutch sleeve fork or differential clutch sleeve.