Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL(w/o Differential Lock) › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0243209 REAR DIFFERENTIAL CARRIER OIL SEAL(w/o Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL(w/o Differential Lock)  REPLACEMENT  


PROCEDURE

Hide 41204B 2.REMOVE REAR DRIVE PINION NUT

a.
C236628N06
1.287,0.537 1.287,0.208 1.287,0.208 1.945,0.208 false 1.988,0.131 2.301,0.297 0.313,0.167 10 SST

Using SST and a hammer, loosen the staked part of the rear drive pinion nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
C236629C06
2.229,1.208 2.656,1.208 false 2.708,1.125 3.031,1.292 0.323,0.167 10 false SST 0.51,0.365 0.677,0.521 0.167,0.156 10 false *a 2.188,1.74 2.354,1.896 0.167,0.156 10 false *b
*a Turn
*b Hold


Using SST to hold the companion flange in place, remove the rear drive pinion nut.

SST
09330-00021  (09330-00030)


Hide 41204 3.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C238724N02
1.615,0.333 2.042,0.333 false 2.094,0.26 2.552,0.458 0.458,0.198 10 false SST

Using SST, remove the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 41201C 4.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C323205C02
1.406,0.854 1.708,0.427 1.708,0.427 1.99,0.427 true 1.188,1.427 1.458,1.844 1.458,1.844 1.813,1.844 true 2.74,1.823 2.458,1.823 2.458,1.823 2.458,1.51 false 2.073,0.333 2.385,0.531 0.313,0.198 10 false *1 1.896,1.76 2.208,1.958 0.313,0.198 10 false *2 2.792,1.74 3.146,1.927 0.354,0.188 10 false SST
*1 Rear Differential Carrier Oil Seal
*2 Rear Differential Drive Pinion Oil Slinger


Using SST, remove the rear differential carrier oil seal.

SST
09308-10010  


Hide 41214 5.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Remove the rear differential drive pinion oil slinger from the differential drive pinion.


Hide 41201B 6.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C323206N01
2.323,0.729 2.323,0.281 2.323,0.281 2.604,0.281 false 2.667,0.188 3.125,0.385 0.458,0.198 10 false SST

Using SST, remove the rear drive pinion front tapered roller bearing (inner).

SST
09556-22010  


b.
C323207N01
1.927,0.729 1.927,0.25 1.927,0.25 2.26,0.25 false 2.333,0.156 2.792,0.354 0.458,0.198 10 false SST

Using SST, tap out the rear drive pinion front tapered roller bearing (outer).

SST
09308-00010  


Hide 41115 7.REMOVE DIFFERENTIAL OIL STORAGE RING

a.

Using a screwdriver and hammer, tap out the differential oil storage ring.


Hide 41231 8.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237515

Remove the rear differential drive pinion bearing spacer from the differential drive pinion.


Hide 41231 9.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237515

Install a new rear differential drive pinion bearing spacer.

HINT:

Make sure the rear differential drive pinion bearing spacer is installed correctly.



Hide 41115 10.INSTALL DIFFERENTIAL OIL STORAGE RING

a.

Using a brass bar and hammer, tap in a new differential oil storage ring.

NOTICE:

Be careful not to damage the differential oil storage ring.



Hide 41201B 11.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C323208N01
0.844,1.51 1.479,1.833 1.479,1.833 2.01,1.833 true 1.49,0.854 1.771,0.365 1.771,0.365 2.365,0.365 false 2.073,1.75 2.531,1.948 0.458,0.198 10 false SST 2.438,0.271 2.896,0.469 0.458,0.198 10 false SST

Using SST and a hammer, tap in the rear drive pinion front tapered roller bearing (outer).

SST
09316-60011  (09316-00011, 09316-00021)


b.

Install the rear drive pinion front tapered roller bearing (inner).


Hide 41214 12.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Install the rear differential drive pinion oil slinger to the differential drive pinion.


Hide 41201C 13.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C328104C01
1.823,0.802 1.823,0.438 1.823,0.438 2.302,0.438 false 1.042,0.031 1.354,0.229 0.313,0.198 10 false *a 2.385,0.365 2.844,0.563 0.458,0.198 10 false SST
*a Rear Differential Carrier Oil Seal Depth


Using SST and a hammer, tap in a new rear differential carrier oil seal.

SST
09214-76011  

Standard oil seal depth:

0.4 to 1.0 mm (0.0158 to 0.0393 in.)



b.

Apply MP grease to the lip of the rear differential carrier oil seal.


Hide 41204 14.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C238725N03
1.615,0.417 1.833,0.25 1.833,0.25 2.219,0.25 false 2.281,0.167 2.74,0.365 0.458,0.198 10 false SST

Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.


c.
C282254C05
0.573,0.594 0.896,0.594 false 3.052,1.115 3.365,1.313 0.313,0.198 10 false *a 0.281,1.063 0.594,1.26 0.313,0.198 10 false *b 0.281,0.51 0.594,0.708 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the companion flange in place, install a new rear drive pinion nut.

SST
09330-00021  (09330-00030)

Limit torque value:

370 N*m (3773 kgf*cm, 273 ft.*lbf) or less



Hide 15.INSPECT TOTAL PRELOAD

a.
C236639

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload:
Bearing Specified Condition
New bearing 1.4 to 2.63 N*m (15 to 26 kgf*cm, 13 to 23 in.*lbf)
Reused bearing 1.4 to 2.42 N*m (15 to 24 kgf*cm, 13 to 21 in.*lbf)


If the result is not as specified, adjust the preload.


Hide 41204B 16.STAKE REAR DRIVE PINION NUT

a.
C236640

Using a chisel and hammer, stake the rear drive pinion nut.