Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/o Differential Lock) › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0243214 REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/o Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/o Differential Lock)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

The following procedures are for BD22 (w/o Differential Lock).


PROCEDURE

Hide 1.ASSEMBLE DIFFERENTIAL CASE

a.
C236671

Install the rear No. 1 differential side gear thrust washer to the side gear.


b.
C236669

Install 2 side gears, 2 pinion gears, 2 rear No. 1 differential side gear thrust washers, 2 pinion gear thrust washers and the pinion shaft in the differential case.

HINT:

Align the holes of the differential case and pinion shaft.



c.
C236668

Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.


d.

Stake the differential case.


Hide 2.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the differential case and differential ring gear.


b.

Heat the differential ring gear in boiling water that is approximately 100°C (212°F).


c.

Carefully remove the differential ring gear from the boiling water.


d.
C327530C01
1.458,1.521 2.948,1.521 true 1.49,1.646 2.542,1.646 2.542,1.646 2.542,1.521 true 3.01,1.427 3.323,1.625 0.313,0.198 10 false *a
*a Matchmark


After the moisture on the differential ring gear has completely evaporated, quickly align the matchmarks on the differential ring gear and differential case and install the differential ring gear to the differential case.


e.

After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and Temporarily install them.

Thread lock:

Toyota Genuine Adhesive 1360K, Three Bond1360K or equivalent



f.

Diametrically tighten the 12 bolts uniformly in several passes.

Torque:
175 N*m (1785 kgf*cm, 129 ft.*lbf)


Hide 41301A 3.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C327523N01
1.865,0.74 2.104,0.51 2.104,0.51 2.365,0.51 false 0.76,1.771 0.99,1.771 0.99,1.771 1.563,1.875 false 2.438,0.417 2.896,0.615 0.458,0.198 10 false SST 0.438,1.677 0.896,1.875 0.458,0.198 10 false SST

Using SST and a press, press the 2 rear differential case bearings onto the differential case.

SST
09950-60010  (09951-00430, 09951-00470, 09951-00480, 09951-00550)
09950-70010  (09951-00560, 09951-00570, 09951-07150)


Hide 41115 4.INSTALL DIFFERENTIAL OIL STORAGE RING

a.
C326884C01
0.969,1.75 1.5,1.75 false 0.885,2.708 1.563,2.708 true 2.042,2.823 2.427,2.917 2.427,2.917 2.833,2.917 true 0.656,1.677 1.115,1.875 0.458,0.198 10 false SST 0.583,2.625 1.042,2.823 0.458,0.198 10 false SST 2.896,2.833 3.208,3.031 0.313,0.198 10 false *1
*1 Differential Oil Storage Ring


Using SST and a hammer, tap in the differential oil storage ring.

SST
09316-60011  (09316-00011, 09316-00071)

NOTICE:

Be careful not to damage the differential oil storage ring.



Hide 41201B 5.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326897C01
0.979,0.49 1.563,0.49 false 0.948,0.865 1.625,0.865 true 1.927,1.021 2.448,1.021 true 0.667,0.406 1.125,0.604 0.458,0.198 10 false SST 0.646,0.781 1.104,0.979 0.458,0.198 10 false SST 2.521,0.927 2.833,1.125 0.313,0.198 10 false *1
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer)


Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011, 09316-00031)


Hide 41201A 6.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326898C01
0.865,0.635 1.427,0.635 false 0.906,1.406 1.375,1.406 true 1.854,1.531 2.427,1.531 true 0.552,0.552 1.01,0.75 0.458,0.198 10 false SST 0.583,1.323 1.042,1.521 0.458,0.198 10 false SST 2.49,1.448 2.802,1.646 0.313,0.198 10 false *1
*1 Rear Drive Pinion Rear Tapered Roller Bearing (Outer)


Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011)
09951-01000  

HINT:

First, install an adjust shim that has the same thickness as the removed adjust shim. After checking the tooth contact pattern, replace the adjust shim with one of a different thickness if necessary.



Hide 41201A 7.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326245N01
0.938,1.177 1.531,1.177 false 0.969,2.063 1.563,2.063 false 0.604,1.094 1.063,1.292 0.458,0.198 10 false SST 0.646,1.979 1.104,2.177 0.458,0.198 10 false SST

Using SST and a press, press the rear drive pinion rear tapered roller bearing (inner) onto the differential drive pinion.

SST
09309-37010  
09630-24014  (09620-24051)


Hide 8.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C326173N01
2.063,2.073 2.49,2.073 false 1.917,2.688 2.448,2.688 false 1.969,0.406 2.385,0.406 false 1.75,2.01 2.208,2.208 0.458,0.198 10 false SST 1.615,2.615 2.073,2.813 0.458,0.198 10 false SST 1.667,0.344 2,0.552 0.333,0.208 10 false SST

Install the differential drive pinion, rear drive pinion front tapered roller bearing (inner).

SST
09316-60011  (09316-00011, 09316-00041)
09608-04031  

HINT:

Install the rear differential drive pinion bearing spacer and rear differential carrier oil seal after adjusting the gear contact pattern.



b.
C325765

Install the rear differential drive pinion oil slinger.


c.
C326885C01
0.875,0.708 1.479,0.708 false 0.563,0.625 1.021,0.823 0.458,0.198 10 false SST 2.979,0.688 3.292,0.885 0.313,0.198 10 false *a 0.458,1.583 0.771,1.781 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



d.

Adjust the drive pinion preload by tightening the drive pinion nut.


e.
C326886N01
1.792,0.479 2.083,0.208 2.083,0.208 2.396,0.208 false 2.469,0.125 2.927,0.323 0.458,0.198 10 false SST

Using SST to hold the companion flange in place, slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Torque:
298 to 678 N*m (3039 to 6913 kgf*cm, 220 to 500 ft.*lbf)

NOTICE:
·

As there is no spacer, tighten a little at a time. Be careful not to overtighten the nut.

·

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.




f.

Using a torque wrench, measure the preload.

Standard Drive Pinion Preload (Starting Torque):

1.99 to 3.65 N*m (21 to 37 kgf*cm, 18 to 32 in.*lbf)


NOTICE:
·

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.

·

Record the differential drive pinion preload for the total preload measurement.




Hide 9.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C236658

Place the 2 rear differential case bearings (outer) to their respective bearings.

HINT:

Make sure the right and left races are not interchanged.



Hide 10.ADJUST DIFFERENTIAL RING GEAR BACKLASH

a.
C331347

Install the plate washer to the RH side (teeth side).

NOTICE:

Make sure that the differential ring gear has backlash.



b.
C326622

Using a dial indicator, while holding the companion flange, measure the ring gear backlash.

Standard backlash (reference):

0.13 to 0.20 mm (0.00512 to 0.00787 in.)



c.
C331348

Refer to the backlash when selecting a plate washer for the RH side (teeth side).


d.
C331349

Select a plate washer for the LH side (back side) so that there is no gap between the rear differential case bearing (outer) and differential case.


e.

Using a plastic-faced hammer, install the plate washer to the LH side (back side).


f.
C326622

Using a dial indicator, adjust the ring gear backlash until it is within the specification.

Standard backlash:

0.13 to 0.20 mm (0.00512 to 0.00787 in.)


HINT:

If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.


NOTICE:
·

There should be no clearance between the plate washer and case.

·

Make sure that there is ring gear backlash.




Hide 11.ADJUST SIDE BEARING PRELOAD

a.
C331350

After adjusting the backlash of the differential ring gear, remove the plate washer from the LH side (back side).


b.
C124163

Using a micrometer, measure the thickness of the plate washer.


c.

Using the backlash as a reference, select a new washer that is 0.05 to 0.20 mm (0.00197 to 0.00787 in.) thicker than the removed plate washer and, using a plastic-faced hammer, tap it in so that it fits against the bearing.

HINT:

Select a plate washer which can be pressed in 2/3 of the full amount with your finger.



d.
C326622

Recheck the ring gear backlash.

Standard backlash:

0.13 to 0.20 mm (0.00512 to 0.00787 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:

An approximately 0.02 mm (0.000787 in.) change in each plate washer results in a 0.03 mm (0.00118 in.) change in the backlash.


Standard Washer LH (Back Side):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-S0025 2.832 mm (0.1115 in.) 90564-S0040 2.413 mm (0.0950 in.)
90564-S0026 2.804 mm (0.1104 in.) 90564-S0041 2.385 mm (0.0939 in.)
90564-S0027 2.777 mm (0.1093 in.) 90564-S0042 2.357 mm (0.0928 in.)
90564-S0028 2.749 mm (0.1082 in.) 90564-S0043 2.329 mm (0.0917 in.)
90564-S0029 2.721 mm (0.1071 in.) 90564-S0044 2.302 mm (0.0906 in.)
90564-S0030 2.693 mm (0.1060 in.) 90564-S0045 2.274 mm (0.0895 in.)
90564-S0031 2.665 mm (0.1049 in.) 90564-S0046 2.246 mm (0.0884 in.)
90564-S0032 2.637 mm (0.1038 in.) 90564-S0047 2.218 mm (0.0873 in.)
90564-S0033 2.609 mm (0.1027 in.) 90564-S0048 2.190 mm (0.0862 in.)
90564-S0034 2.581 mm (0.1016 in.) 90564-S0049 2.162 mm (0.0851 in.)
90564-S0035 2.553 mm (0.1005 in.) 90564-S0050 2.134 mm (0.0840 in.)
90564-S0036 2.525 mm (0.0994 in.) 90564-S0051 2.860 mm (0.1126 in.)
90564-S0037 2.497 mm (0.0983 in.) 90564-S0052 2.888 mm (0.1137 in.)
90564-S0038 2.469 mm (0.0972 in.) 90564-S0053 2.916 mm (0.1148 in.)
90564-S0039 2.441 mm (0.0961 in.) 90564-S0054 2.944 mm (0.1159 in.)


Standard Washer RH (Teeth Side):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-S0055 0.76 mm (0.0299 in.) 90564-S0091 1.68 mm (0.0661 in.)
90564-S0056 0.79 mm (0.0311 in.) 90564-S0092 1.70 mm (0.0669 in.)
90564-S0057 0.81 mm (0.0319 in.) 90564-S0093 1.73 mm (0.0681 in.)
90564-S0058 0.84 mm (0.0331 in.) 90564-S0094 1.75 mm (0.0689 in.)
90564-S0059 0.86 mm (0.0339 in.) 90564-S0095 1.78 mm (0.0701 in.)
90564-S0060 0.89 mm (0.0350 in.) 90564-S0096 1.80 mm (0.0709 in.)
90564-S0061 0.91 mm (0.0358 in.) 90564-S0097 1.83 mm (0.0720 in.)
90564-S0062 0.94 mm (0.0370 in.) 90564-S0098 1.85 mm (0.0728 in.)
90564-S0063 0.97 mm (0.0382 in.) 90564-S0099 1.88 mm (0.0740 in.)
90564-S0064 0.99 mm (0.0390 in.) 90564-S0100 1.91 mm (0.0752 in.)
90564-S0065 1.02 mm (0.0402 in.) 90564-S0101 1.93 mm (0.0760 in.)
90564-S0066 1.04 mm (0.0409 in.) 90564-S0102 1.96 mm (0.0772 in.)
90564-S0067 1.07 mm (0.0421 in.) 90564-S0103 1.98 mm (0.0780 in.)
90564-S0068 1.09 mm (0.0429 in.) 90564-S0104 2.01 mm (0.0791 in.)
90564-S0069 1.12 mm (0.0441 in.) 90564-S0105 2.03 mm (0.0799 in.)
90564-S0070 1.14 mm (0.0449 in.) 90564-S0106 2.06 mm (0.0811 in.)
90564-S0071 1.17 mm (0.0461 in.) 90564-S0107 2.08 mm (0.0819 in.)
90564-S0072 1.19 mm (0.0469 in.) 90564-S0108 2.11 mm (0.0831 in.)
90564-S0073 1.22 mm (0.0480 in.) 90564-S0109 2.13 mm (0.0839 in.)
90564-S0074 1.24 mm (0.0488 in.) 90564-S0110 2.16 mm (0.0850 in.)
90564-S0075 1.27 mm (0.0500 in.) 90564-S0111 2.18 mm (0.0858 in.)
90564-S0076 1.30 mm (0.0512 in.) 90564-S0112 2.21 mm (0.0870 in.)
90564-S0077 1.32 mm (0.0520 in.) 90564-S0113 2.24 mm (0.0882 in.)
90564-S0078 1.35 mm (0.0531 in.) 90564-S0114 2.26 mm (0.0890 in.)
90564-S0079 1.37 mm (0.0539 in.) 90564-S0115 2.29 mm (0.0902 in.)
90564-S0080 1.40 mm (0.0551 in.) 90564-S0116 2.31 mm (0.0909 in.)
90564-S0081 1.42 mm (0.0559 in.) 90564-S0117 2.34 mm (0.0921 in.)
90564-S0082 1.45 mm (0.0571 in.) 90564-S0118 2.36 mm (0.0929 in.)
90564-S0083 1.47 mm (0.0579 in.) 90564-S0119 2.39 mm (0.0941 in.)
90564-S0084 1.50 mm (0.0591 in.) 90564-S0120 2.41 mm (0.0949 in.)
90564-S0085 1.52 mm (0.0598 in.) 90564-S0121 2.44 mm (0.0961 in.)
90564-S0086 1.55 mm (0.0610 in.) 90564-S0122 2.46 mm (0.0969 in.)
90564-S0087 1.57 mm (0.0618 in.) 90564-S0123 2.49 mm (0.0980 in.)
90564-S0088 1.60 mm (0.0630 in.) 90564-S0124 2.51 mm (0.0988 in.)
90564-S0089 1.63 mm (0.0642 in.) 90564-S0125 2.54 mm (0.1000 in.)
90564-S0090 1.65 mm (0.0650 in.) - -



Hide 12.INSPECT TOTAL PRELOAD

a.
C326896

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

Standard Total Preload:
Reduction Ratio Specified Condition
3.909 1.95 to 3.94 N*m (20 to 40 kgf*cm, 18 to 34 in.*lbf)
4.300 1.93 to 3.89 N*m (20 to 39 kgf*cm, 18 to 34 in.*lbf)
4.555 1.91 to 3.86 N*m (20 to 39 kgf*cm, 17 to 34 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 13.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

C327699

a.

Coat 3 or 4 teeth at 3 different positions on the differential ring gear with Prussian blue.


b.

Hold the companion flange firmly in place and rotate the differential ring gear in both directions.


c.

Inspect the tooth contact pattern.

C222533C02
1.49,1.177 1.906,1.427 0.417,0.25 10 false *a 2.479,0.313 2.865,0.521 0.385,0.208 12 false *A 3.115,0.708 3.51,0.948 0.396,0.24 10 false *b 5.146,0.708 5.521,0.948 0.375,0.24 10 false *c 4.417,1.531 4.99,1.917 0.573,0.385 10 false *d 3.167,2.531 3.677,2.865 0.51,0.333 10 false *e 5.198,2.552 5.573,2.865 0.375,0.313 10 false *f 4.479,3.354 4.896,3.771 0.417,0.417 10 false *g 2.469,4.51 3.052,4.833 0.583,0.323 12 false *B 3.208,5.104 3.615,5.406 0.406,0.302 10 false *h 5.198,5.115 5.5,5.365 0.302,0.25 10 false *i 3.198,7.042 3.604,7.406 0.406,0.365 10 false *j 5.167,7.052 5.656,7.427 0.49,0.375 10 false *k 4.49,5.969 4.958,6.333 0.469,0.365 10 false *d 4.469,7.906 4.906,8.396 0.438,0.49 10 false *g
*A Drive Side *B Coast Side
*a Proper Contact *b Toe Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear.
*e Heel Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear. *h Heel Contact
*i Flank Contact *j Toe Contact
*k Face Contact - -


C217047C04
2.01,1.625 1.469,1.625 1.469,1.625 1.469,1.354 false 1.042,1.896 0.75,1.896 0.75,1.896 0.75,1.51 false 1.104,1.813 1.417,2.01 0.313,0.198 10 false *1 2.052,1.563 2.365,1.76 0.313,0.198 10 false *2
*1 Adjust Shim
*2 Rear Drive Pinion Rear Tapered Roller Bearing (Outer)


If the teeth are not contacting properly, use the following chart to select a proper adjust shim.


Standard Adjust Shim Thickness:
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-S0001 1.025 mm (0.0404 in.) 90564-S0011 1.275 mm (0.0502 in.)
90564-S0002 1.050 mm (0.0413 in.) 90564-S0012 1.300 mm (0.0512 in.)
90564-S0003 1.075 mm (0.0423 in.) 90564-S0013 1.325 mm (0.0522 in.)
90564-S0004 1.100 mm (0.0433 in.) 90564-S0014 1.350 mm (0.0531 in.)
90564-S0005 1.125 mm (0.0443 in.) 90564-S0015 1.375 mm (0.0541 in.)
90564-S0006 1.150 mm (0.0453 in.) 90564-S0016 1.400 mm (0.0551 in.)
90564-S0007 1.175 mm (0.0463 in.) 90564-S0017 1.425 mm (0.0561 in.)
90564-S0008 1.200 mm (0.0472 in.) 90564-S0018 1.450 mm (0.0571 in.)
90564-S0009 1.225 mm (0.0482 in.) 90564-S0019 1.475 mm (0.0581 in.)
90564-S0010 1.250 mm (0.0492 in.) - -



Hide 41204 15.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41201A 25.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326898C01
0.865,0.635 1.427,0.635 false 0.906,1.406 1.375,1.406 true 1.854,1.531 2.427,1.531 true 0.552,0.552 1.01,0.75 0.458,0.198 10 false SST 0.583,1.323 1.042,1.521 0.458,0.198 10 false SST 2.49,1.448 2.802,1.646 0.313,0.198 10 false *1
*1 Rear Drive Pinion Rear Tapered Roller Bearing (Outer)


Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011)
09951-01000  


Hide 41115 26.INSTALL DIFFERENTIAL OIL STORAGE RING

a.
C326884C01
0.969,1.75 1.5,1.75 false 0.885,2.708 1.563,2.708 true 2.042,2.823 2.427,2.917 2.427,2.917 2.833,2.917 true 0.656,1.677 1.115,1.875 0.458,0.198 10 false SST 0.583,2.625 1.042,2.823 0.458,0.198 10 false SST 2.896,2.833 3.208,3.031 0.313,0.198 10 false *1
*1 Differential Oil Storage Ring


Using SST and a hammer, tap in a new differential oil storage ring.

SST
09316-60011  (09316-00011)

NOTICE:

Be careful not to damage the differential oil storage ring.



Hide 41201B 27.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326897C01
0.979,0.49 1.563,0.49 false 0.948,0.865 1.625,0.865 true 1.927,1.021 2.448,1.021 true 0.667,0.406 1.125,0.604 0.458,0.198 10 false SST 0.646,0.781 1.104,0.979 0.458,0.198 10 false SST 2.521,0.927 2.833,1.125 0.313,0.198 10 false *1
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer)


Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011, 09316-00031)


Hide 41231 28.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C325767

Install a new rear differential drive pinion bearing spacer.


Hide 41201B 29.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326404

Install the rear drive pinion front tapered roller bearing (inner).


Hide 30.INSTALL DIFFERENTIAL DRIVE PINION

a.
C326173N01
2.063,2.073 2.49,2.073 false 1.917,2.688 2.448,2.688 false 1.969,0.406 2.385,0.406 false 1.75,2.01 2.208,2.208 0.458,0.198 10 false SST 1.615,2.615 2.073,2.813 0.458,0.198 10 false SST 1.667,0.344 2,0.552 0.333,0.208 10 false SST

Using SST and a press, install the differential drive pinion.

SST
09316-60011  (09316-00011, 09316-00041)
09608-04031  


Hide 31.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C326625

Place the 2 rear differential case bearings (outer) to their respective bearings.

HINT:

Make sure the right and left races are not interchanged.



Hide 32.INSTALL DIFFERENTIAL BEARING CAP

a.

Install the 2 plate washers.


b.
C326623C02
0.427,1.208 1.583,1.208 true 0.75,1.198 0.74,0.844 0.74,0.844 1.167,0.844 true 0.24,1.104 0.552,1.302 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the differential bearing cap and differential carrier.


c.

Install the right and left differential bearing caps with the 4 bolts.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 41214 33.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C325765

Install the rear differential drive pinion oil slinger to the differential drive pinion.


Hide 41201C 34.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

Hide 41204 35.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C326885C01
0.875,0.708 1.479,0.708 false 0.563,0.625 1.021,0.823 0.458,0.198 10 false SST 2.979,0.688 3.292,0.885 0.313,0.198 10 false *a 0.458,1.583 0.771,1.781 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.


c.
C326916C01
0.427,0.677 0.604,0.677 0.604,0.677 0.76,0.865 false 3.115,1.167 3.427,1.365 0.313,0.198 10 false *a 0.208,1.385 0.521,1.583 0.313,0.198 10 false *b 0.115,0.615 0.573,0.813 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the companion flange in place, install a new nut.

SST
09330-00021  (09330-00030)

Torque:
298 to 678 N*m (3039 to 6913 kgf*cm, 220 to 500 ft.*lbf)


Hide 36.INSPECT TOTAL PRELOAD

a.

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.


b.
C326896

Using a torque wrench, measure the total preload.

Standard Total Preload:
Reduction Ratio Preload
3.909 2.25 to 4.24 N*m (23 to 43 kgf*cm, 20 to 37 in.*lbf)
4.300 2.23 to 4.19 N*m (23 to 42 kgf*cm, 20 to 37 in.*lbf)
4.555 2.21 to 4.16 N*m (23 to 42 kgf*cm, 20 to 36 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 37.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C326622

Using a dial indicator, check the backlash of the differential ring gear.

Standard backlash:

0.13 to 0.20 mm (0.00512 to 0.00787 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.



Hide 41204 38.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C325516C01
2.573,1.906 2.885,2.104 0.313,0.198 10 false *a
*a 36 mm (1.42 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)