Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for Pre-Runner) › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0243217 REAR DIFFERENTIAL CARRIER ASSEMBLY(for Pre-Runner) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for Pre-Runner)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

The following procedures are for BD20 (w/o Differential Lock).


PROCEDURE

Hide 41110 1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

a.
C326608

Secure the differential carrier.


Hide 41204 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C236648C06
2.479,1.813 2.656,1.969 0.177,0.156 10 false *a
*a 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.



Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C326609C01
2.865,1.552 3.177,1.75 0.313,0.198 10 false *a
*a 92 mm (3.62 in.)


Using a dial indicator, check the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

C327529

a.

Using a dial indicator, check the backlash of the ring gear.

Backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 41204 7.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41214 9.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 10.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326610N01
2.333,0.781 2.333,0.417 2.333,0.417 2.625,0.417 false 2.698,0.323 3.156,0.521 0.458,0.198 10 false SST

Using SST, remove the rear drive pinion front tapered roller bearing (inner) from the differential drive pinion.

SST
09556-22010  


Hide 41316 11.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C326611

Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.


Hide 12.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C326612C01
0.375,1.344 1.615,1.344 true 1.01,1.354 1.01,1.25 1.01,1.25 1.615,1.25 true 0.792,1.344 0.792,0.969 0.792,0.969 1.198,0.969 true 0.594,1.344 0.594,0.865 0.594,0.865 1.198,0.865 true 0.188,1.24 0.5,1.438 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 rear differential bearing adjusting nuts.


d.
C236658

Remove the rear differential case assembly from the differential carrier.

HINT:

Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.



Hide 13.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the differential drive pinion and rear differential drive pinion bearing spacer from the differential carrier.


Hide 41201A 14.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237656N04
2.731,0.394 3.04,0.551 0.309,0.157 10 SST 2.334,1.03 2.605,0.467 2.605,0.467 2.697,0.467 false

Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner) and rear differential drive pinion plate washer from the differential drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the differential drive pinion.


HINT:

If the differential drive pinion or differential ring gear is damaged, replace them as a set.



Hide 41201B 15.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237657N02
1.323,0.141 1.635,0.304 0.313,0.163 10 SST 1.056,0.223 1.297,0.223 false

Using SST, remove the rear drive pinion front tapered roller bearing (outer) from the differential carrier.

SST
09308-00010  


b.

Using a brass bar and hammer, tap out the differential oil storage ring from the differential carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 41201A 16.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C236662

Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer) from the differential carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 17.REMOVE DIFFERENTIAL RING GEAR

a.
C326613C01
1.771,1.25 3.104,1.25 true 1.76,1.125 2.448,1.125 2.448,1.125 2.448,1.25 true 3.146,1.156 3.385,1.375 0.24,0.219 10 false *a
*a Matchmark


Place matchmarks on the differential ring gear and differential case.


b.

Remove the 10 differential ring gear set bolts.


c.
C326614

Using a plastic-faced hammer, tap on the differential ring gear to separate it from the differential case.


Hide 18.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.

a.

Install the rear differential case bearings (outer) to the differential case.


b.

Install the differential case to the differential carrier.


c.

Install the 2 adjusting nuts.


d.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
85.3 N*m (870 kgf*cm, 63 ft.*lbf)


e.
C331345C01
0.229,1.25 0.542,1.448 0.313,0.198 10 false *a
*a 87 mm (3.43 in.)


Using a dial indicator, measure the differential case runout.

Maximum runout:

0.07 mm (0.00276 in.)



f.

Remove the 4 bolts and 2 differential bearing caps.


g.

Remove the 2 rear differential bearing adjusting nuts.


h.

Remove the differential case assembly.


i.

Remove the rear differential case bearings (outer).


Hide 41301A 19.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C326615C01
0.979,0.625 0.979,0.281 0.979,0.281 0.719,0.281 false 0.396,0.198 0.854,0.396 0.458,0.198 10 false SST 2.688,0.177 3,0.375 0.313,0.198 10 false *a 0.188,0.958 0.5,1.156 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, remove the 2 rear differential case bearings (inner) from the differential case.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00360)

HINT:

Do not remove the rear differential case bearings when not replacing the differential case.



Hide 20.DISASSEMBLE DIFFERENTIAL CASE

a.
C236667

Using a chisel and hammer, unstake the differential case.


b.
C326616

Using a pin punch and hammer, tap out the straight pin.


c.
C236669

Remove the following parts from the differential case.

1.
C236670C04
0.563,0.542 0.563,0.219 0.563,0.219 0.396,0.219 false 0.906,0.635 0.906,0.167 0.906,0.167 0.979,0.167 false 1.635,1.052 1.635,0.5 1.635,0.5 1.49,0.5 false 2.063,0.479 2.063,0.125 2.063,0.125 1.958,0.125 false 2.75,0.51 3,0.51 false 2.375,1.604 2.375,1.854 false 2.75,1.688 2.75,1.833 false 0.552,1.458 0.552,1.177 0.552,1.177 0.427,1.177 false 1.146,1.708 1.146,1.896 1.146,1.896 1.292,1.896 false 1.365,1.813 1.573,1.979 0.208,0.167 10 false *1 0.198,0.146 0.406,0.313 0.208,0.167 10 false *5 1.281,0.427 1.49,0.594 0.208,0.167 10 false *3 1.76,0.052 1.969,0.219 0.208,0.167 10 false *1 3.052,0.427 3.26,0.594 0.208,0.167 10 false *2 2.313,1.906 2.521,2.073 0.208,0.167 10 false *4 2.708,1.885 2.917,2.052 0.208,0.167 10 false *5 1.052,0.104 1.26,0.271 0.208,0.167 10 false *4 0.229,1.115 0.438,1.281 0.208,0.167 10 false *2
*1 Side Gear
*2 Rear No. 1 Differential Side Gear Thrust Washer
*3 Pinion Shaft
*4 Pinion Gear
*5 Pinion Gear Thrust Washer


Side gear (2 pieces)

2.

Rear No. 1 differential side gear thrust washer (2 pieces)

3.

Pinion shaft

4.

Pinion gear (2 pieces)

5.

Pinion gear thrust washer (2 pieces)



d.

Using a chisel and hammer, unstake the differential case.


Hide 21.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.



Hide 22.INSPECT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.