Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212879 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the certification ECU (smart key ECU assembly); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the smart entry and wireless function.

WIRING DIAGRAM

for LHD:
B405298E03
3.271,1.771 3.583,1.969 0.313,0.198 10 false +B 3.458,2.188 7.156,2.406 3.698,0.219 10 false IG1D 3.865,2.313 4.323,2.531 0.458,0.219 10 false G16 3.875,5.781 4.333,6 0.458,0.219 10 false G16 2.25,4.677 2.708,4.896 0.458,0.219 10 false G17 2.25,4.188 2.708,4.406 0.458,0.219 10 false G17 2.25,3.698 2.708,3.917 0.458,0.219 10 false G17 2.25,1.448 2.708,1.667 0.458,0.219 10 false G16 2.24,0.979 2.698,1.198 0.458,0.219 10 false G17 2.25,0.521 2.708,0.74 0.458,0.219 10 false G16 1.521,0.667 2.094,0.938 0.573,0.271 10 false SMART 1.344,1.135 2.24,1.427 0.896,0.292 10 false ECU-B NO. 1 0.208,0.5 1.156,0.865 0.948,0.365 10 false from Battery 0.198,0.969 1.146,1.333 0.948,0.365 10 false from Battery 2.323,0.333 2.781,0.552 0.458,0.219 10 false 1 2.292,0.813 2.75,1.031 0.458,0.219 10 false 33 2.313,1.271 2.771,1.49 0.458,0.219 10 false 10 2.583,0.51 7.156,0.771 4.573,0.26 10 false +B 2.583,0.979 7.156,1.24 4.573,0.26 10 false CUTB 2.583,1.333 7.156,1.594 4.573,0.26 10 false E 2.552,3.604 7.125,3.865 4.573,0.26 10 false RCO 2.563,4.083 7.156,4.344 4.594,0.26 10 false RDAS 2.563,4.583 7.156,4.844 4.594,0.26 10 false CSEL 2.302,4.49 2.76,4.708 0.458,0.219 10 false 21 2.302,4 2.76,4.219 0.458,0.219 10 false 22 2.344,3.51 2.802,3.729 0.458,0.219 10 false 3 1.344,3.604 1.802,3.823 0.458,0.219 10 false +5 1.615,3.604 2.073,3.823 0.458,0.219 10 false 4 1.615,4.073 2.073,4.292 0.458,0.219 10 false 5 1.625,4.552 2.083,4.771 0.458,0.219 10 false 2 1.615,5.208 2.073,5.427 0.458,0.219 10 false 1 1.208,5.219 1.667,5.438 0.458,0.219 10 false GND 1.146,4.563 1.604,4.781 0.458,0.219 10 false CSEL 1.125,4.073 1.583,4.292 0.458,0.219 10 false DATA 0.646,4.177 1.104,4.396 0.458,0.219 10 false IC 0.646,4.781 1.104,5 0.458,0.219 10 false IC 3.385,4.229 3.844,4.448 0.458,0.219 10 false IC 2.938,2.208 3.396,2.427 0.458,0.219 10 false IC 2.927,5.635 3.385,5.854 0.458,0.219 10 false IC 3.281,5.198 3.594,5.396 0.313,0.198 10 false +B 0.469,5.75 0.781,5.948 0.313,0.198 10 false G25 0.469,5.938 2.188,6.448 1.719,0.51 10 false Door Control Receiver 2.385,7.24 3.917,7.792 1.531,0.552 10 false Certification ECU (Smart Key ECU Assembly) 4.26,6.49 7.083,6.781 2.823,0.292 10 false Instrument Panel Junction Block Assembly 3.417,5.656 7.156,5.875 3.74,0.219 10 false ACCD 3.906,5.594 4.365,5.813 0.458,0.219 10 false 21 3.927,2.125 4.385,2.344 0.458,0.219 10 false 20 4.427,5.781 4.885,6 0.458,0.219 10 false 2E 4.469,5.604 4.927,5.823 0.458,0.219 10 false 2 4.427,5.365 4.885,5.583 0.458,0.219 10 false 2R 4.469,5.188 4.927,5.406 0.458,0.219 10 false 1 5,6.094 5.458,6.313 0.458,0.219 10 false ACC 5.49,5.5 6.552,5.698 1.063,0.198 10 false SFT LOCK-ACC 6.563,5.375 7.021,5.594 0.458,0.219 10 false 2P 6.573,5.792 7.031,6.01 0.458,0.219 10 false 2J 6.604,5.615 7.063,5.833 0.458,0.219 10 false 5 5.073,2.938 5.531,3.156 0.458,0.219 10 false 5 5.521,4.083 7.156,4.354 1.635,0.271 10 false form AM2 NO. 2 Fuse 6.396,3.01 7.156,3.323 0.76,0.313 10 false to Fuses 6.396,1.865 7.156,2.177 0.76,0.313 10 false to Fuses 5.958,1.438 7.063,1.802 1.104,0.365 10 false form AM1 Fuse 5.167,2.604 5.927,2.917 0.76,0.313 10 false IG1 NO. 1 5.385,3.76 6.146,4.073 0.76,0.313 10 false IG2 5.083,3.354 5.542,3.573 0.458,0.219 10 false 1 5.063,2.198 5.521,2.417 0.458,0.219 10 false 1 5.073,1.781 5.531,2 0.458,0.219 10 false 5 5.813,3.354 6.271,3.563 0.458,0.208 10 false 2 5.833,2.198 6.292,2.406 0.458,0.208 10 false 2 5.833,2.917 6.292,3.125 0.458,0.208 10 false 3 5.813,1.771 6.271,1.979 0.458,0.208 10 false 3 6.604,5.188 7.063,5.406 0.458,0.219 10 false 5

for RHD:
B405298E05
3.271,1.771 3.583,1.969 0.313,0.198 10 false +B 3.458,2.188 7.156,2.406 3.698,0.219 10 false IG1D 3.865,2.313 4.323,2.531 0.458,0.219 10 false G16 3.875,5.781 4.333,6 0.458,0.219 10 false G16 2.25,4.677 2.708,4.896 0.458,0.219 10 false G17 2.25,4.188 2.708,4.406 0.458,0.219 10 false G17 2.25,3.698 2.708,3.917 0.458,0.219 10 false G17 2.25,1.448 2.708,1.667 0.458,0.219 10 false G16 2.24,0.979 2.698,1.198 0.458,0.219 10 false G17 2.25,0.521 2.708,0.74 0.458,0.219 10 false G16 1.521,0.667 2.094,0.938 0.573,0.271 10 false SMART 1.344,1.135 2.24,1.427 0.896,0.292 10 false ECU-B NO. 1 0.208,0.5 1.156,0.865 0.948,0.365 10 false from Battery 0.198,0.969 1.146,1.333 0.948,0.365 10 false from Battery 2.323,0.333 2.781,0.552 0.458,0.219 10 false 1 2.292,0.813 2.75,1.031 0.458,0.219 10 false 33 2.313,1.271 2.771,1.49 0.458,0.219 10 false 10 2.583,0.51 7.156,0.771 4.573,0.26 10 false +B 2.583,0.979 7.156,1.24 4.573,0.26 10 false CUTB 2.583,1.333 7.156,1.594 4.573,0.26 10 false E 2.552,3.604 7.125,3.865 4.573,0.26 10 false RCO 2.563,4.083 7.156,4.344 4.594,0.26 10 false RDAS 2.563,4.583 7.156,4.844 4.594,0.26 10 false CSEL 2.302,4.49 2.76,4.708 0.458,0.219 10 false 21 2.302,4 2.76,4.219 0.458,0.219 10 false 22 2.344,3.51 2.802,3.729 0.458,0.219 10 false 3 1.344,3.604 1.802,3.823 0.458,0.219 10 false +5 1.615,3.604 2.073,3.823 0.458,0.219 10 false 4 1.615,4.073 2.073,4.292 0.458,0.219 10 false 5 1.625,4.552 2.083,4.771 0.458,0.219 10 false 2 1.615,5.208 2.073,5.427 0.458,0.219 10 false 1 1.208,5.219 1.667,5.438 0.458,0.219 10 false GND 1.146,4.563 1.604,4.781 0.458,0.219 10 false CSEL 1.125,4.073 1.583,4.292 0.458,0.219 10 false DATA 0.646,4.177 1.104,4.396 0.458,0.219 10 false IC 0.646,4.781 1.104,5 0.458,0.219 10 false IC 3.406,4.229 3.865,4.448 0.458,0.219 10 false IC 2.938,2.208 3.396,2.427 0.458,0.219 10 false IC 2.927,5.635 3.385,5.854 0.458,0.219 10 false IC 3.281,5.198 3.594,5.396 0.313,0.198 10 false +B 0.469,5.75 0.781,5.948 0.313,0.198 10 false G25 0.469,5.938 2.188,6.448 1.719,0.51 10 false Door Control Receiver 2.385,7.24 3.917,7.792 1.531,0.552 10 false Certification ECU (Smart Key ECU Assembly) 4.26,6.49 7.083,6.781 2.823,0.292 10 false Instrument Panel Junction Block Assembly 3.417,5.656 7.156,5.875 3.74,0.219 10 false ACCD 3.906,5.594 4.365,5.813 0.458,0.219 10 false 21 3.927,2.125 4.385,2.344 0.458,0.219 10 false 20 4.427,5.781 4.885,6 0.458,0.219 10 false 2E 4.469,5.604 4.927,5.823 0.458,0.219 10 false 2 4.427,5.365 4.885,5.583 0.458,0.219 10 false 2A 4.469,5.188 4.927,5.406 0.458,0.219 10 false 1 5,6.094 5.458,6.313 0.458,0.219 10 false ACC 5.49,5.5 6.552,5.698 1.063,0.198 10 false SFT LOCK-ACC 6.563,5.375 7.021,5.594 0.458,0.219 10 false 2P 6.573,5.792 7.031,6.01 0.458,0.219 10 false 2J 6.604,5.615 7.063,5.833 0.458,0.219 10 false 5 5.073,2.938 5.531,3.156 0.458,0.219 10 false 5 5.521,4.083 7.156,4.354 1.635,0.271 10 false form AM2 NO. 2 Fuse 6.396,3.01 7.156,3.323 0.76,0.313 10 false to Fuses 6.396,1.865 7.156,2.177 0.76,0.313 10 false to Fuses 5.958,1.438 7.063,1.802 1.104,0.365 10 false form AM1 Fuse 5.167,2.604 5.927,2.917 0.76,0.313 10 false IG1 NO. 1 5.385,3.76 6.146,4.073 0.76,0.313 10 false IG2 5.083,3.354 5.542,3.573 0.458,0.219 10 false 1 5.063,2.198 5.521,2.417 0.458,0.219 10 false 1 5.073,1.781 5.531,2 0.458,0.219 10 false 5 5.813,3.354 6.271,3.563 0.458,0.208 10 false 2 5.833,2.198 6.292,2.406 0.458,0.208 10 false 2 5.833,2.917 6.292,3.125 0.458,0.208 10 false 3 5.813,1.771 6.271,1.979 0.458,0.208 10 false 3 6.604,5.188 7.063,5.406 0.458,0.219 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).

While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or DTC B27B0 is not output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION



HINT:
·

If all door entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52
Radio Wave Interference
Parameter Name Cause of Problem and Countermeasure
Lock / Key RF Signal Interference When entry lock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry lock operation has been successfully performed, the possibility of wave interference is high.
Unlock / Key RF Signal Interference When entry unlock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry unlock operation has been successfully performed, the possibility of wave interference is high.
Operating Trunk Switch / Key RF Signal Interference When entry back door open operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry back door open operation has been successfully performed, the possibility of wave interference is high.

PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the voltage of the vehicle battery.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the GTS and check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

When using the GTS with the engine switch off to troubleshoot, connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.


OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK DOOR AJAR WARNING OPERATION

NG

3.CHECK DOOR AJAR WARNING OPERATION
a.

When door unlock by entry lock or wireless door lock operation functions even though all doors are closed, check the door ajar warning operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>SYSTEM DESCRIPTION


Result:
Result Proceed to
Door ajar warning does not operate. A
Door ajar warning operates. B



A

4.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

4.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window master switch on the driver door is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

5.CHECK KEY DIAGNOSTIC MODE

NG

5.CHECK KEY DIAGNOSTIC MODE

b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
i.
B406013C04
2.781,1.188 3.094,1.385 0.313,0.198 10 false *a 0.021,0.021 0.333,0.219 0.313,0.198 12 false *A
*A for LHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


B406012C05
0.844,1.167 1.156,1.365 0.313,0.198 10 false *a 0.021,0.031 0.396,0.271 0.375,0.24 12 false *A
*A for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for Driver Door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for Driver Door), check that the wireless door lock buzzer sounds.


ii.
B406012C05
0.844,1.167 1.156,1.365 0.313,0.198 10 false *a 0.021,0.031 0.396,0.271 0.375,0.24 12 false *A
*A for LHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


B406013C04
2.781,1.188 3.094,1.385 0.313,0.198 10 false *a 0.021,0.021 0.333,0.219 0.313,0.198 12 false *A
*A for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for Front Passenger Door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for Front Passenger Door), check that the wireless door lock buzzer sounds.


iii.
B406016C01
0.583,0.833 2.615,0.365 2.615,0.365 1.719,0.844 true 2.646,0.271 2.958,0.469 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.


iv.
B406019C01
0.594,0.677 2.385,0.313 2.385,0.313 1.75,0.667 true 2.448,0.208 2.76,0.406 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.


v.
B412168C01
1.938,1.063 2.438,0.198 2.438,0.198 1.344,1.563 true 2.51,0.135 2.823,0.333 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (inside luggage):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.


vi.
B412169C01
1.781,1.198 2.094,1.396 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the No. 2 indoor electrical key antenna assembly (back door):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.



OK:

Wireless door lock buzzer sounds.


Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspection succeeds for only one of the channels C



A

6.CHECK WAVE ENVIRONMENT

B

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

29.CHECK WAVE ENVIRONMENT
6.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.



Result:
Proceed to
OK
NG



OK

7.CHECK TRANSMITTER BATTERY

NG

AFFECTED BY WAVE INTERFERENCE

7.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C


HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.






A

8.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

9.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

8.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery.

NOTICE:

When removing the transmitter battery, make sure not to touch the electronic circuit board, as static electricity may cause a malfunction to occur.




Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

9.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assembly B



A

10.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

11.CHECK ENTRY DOOR LOCK OPERATION
10.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK ENTRY DOOR LOCK OPERATION
11.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G25 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-3 (RCO) - G25-4 (+5) Always Below 1 Ω
G17-22 (RDAS) - G25-5 (DATA) Always Below 1 Ω
G17-21 (CSEL) - G25-2 (CSEL) Always Below 1 Ω
G16-10 (E) - Body ground Always Below 1 Ω
G25-1 (GND) - Body ground Always Below 1 Ω
G17-3 (RCO) or G25-4 (+5) - Body ground Always 10 kΩ or higher
G17-22 (RDAS) or G25-5 (DATA) - Body ground Always 10 kΩ or higher
G17-21 (CSEL) or G25-2 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Connect the G25 door control receiver connector.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

14.CHECK DOOR CONTROL RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

14.CHECK DOOR CONTROL RECEIVER
a.

Measure the resistance according to the value(s) in the table below.

B327899C20
1.594,0.333 2.042,0.563 0.448,0.229 1.156,2.063 1.51,1.281 true 2.51,2.073 2.156,1.281 true 1.719,0.375 2.177,0.573 0.458,0.198 10 false G25 3.719,1.219 4.177,1.417 0.458,0.198 10 false GND 4.385,1.948 4.844,2.146 0.458,0.198 10 false *c 3.948,0.396 4.406,0.594 0.458,0.198 10 false *b 0.333,0.24 0.792,0.438 0.458,0.198 10 false *a 0.99,2.104 1.448,2.302 0.458,0.198 10 false DATA 5.396,1.958 5.854,2.156 0.458,0.198 10 false *d 2.385,2.104 2.844,2.302 0.458,0.198 10 false GND
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed


Standard Resistance:
Tester Connection Condition Specified Condition
G25-1 (GND) - Body ground Always Below 1 Ω



b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
G25-5 (DATA) - G25-1 (GND)
Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

B348668C11
1.625,0.469 2.052,0.698 0.427,0.229 2.948,2.177 2.167,1.25 true 2.25,2.188 2,1.271 true 1.344,2.188 1.677,1.271 true 0.76,0.5 1.073,0.698 0.313,0.198 10 false *a 3.854,0.583 4.167,0.781 0.313,0.198 10 false *b 2.823,2.219 3.135,2.417 0.313,0.198 10 false GND 1.26,2.219 1.573,2.417 0.313,0.198 10 false +5 2.073,2.219 2.552,2.417 0.479,0.198 10 false CSEL 3.667,1.333 3.979,1.531 0.313,0.198 10 false GND 1.719,0.5 2.031,0.698 0.313,0.198 10 false G25
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1


Standard Voltage:
Tester Connection Condition Specified Condition
G25-4 (+5) - G25-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed


Below 1 V → 4.5 to 5.5 V



b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
G25-2 (CSEL) - G25-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B418158C01
2.479,0.396 2.875,0.646 0.396,0.25 2.583,1.396 3.031,2.042 3.031,2.042 3.229,2.042 true 2.5,1.406 2.229,2.021 2.229,2.021 2,2.021 true 0.313,0.135 0.625,0.292 0.313,0.156 10 false *a 2.563,0.427 3,0.594 0.438,0.167 10 false G16 1.542,1.948 2.115,2.115 0.573,0.167 10 false ACCD 3.271,1.958 3.844,2.125 0.573,0.167 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state ST ON, ALL OFF, IG ON or ACC ON ALL OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG) (IG1 relay on)
ST ON: Sending engine start request signal
-

f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-20 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9 V or higher
G16-21 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) 8.5 V or higher
Engine switch on (IG) 8.5 V or higher


HINT:

Using the GTS, measure the voltage while confirming the power source mode on the Data List.



Result:
Proceed to
OK
NG



OK

19.INSPECT IG1 NO.1 RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

19.INSPECT IG1 NO.1 RELAY

OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 NO.1 RELAY)

NG

REPLACE IG1 NO.1 RELAY

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 NO.1 RELAY)

OK

21.INSPECT IG2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT IG2 RELAY

OK

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)

NG

REPLACE IG2 RELAY

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)

OK

23.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

OK

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ACC RELAY)

NG

REPLACE ACC RELAY

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ACC RELAY)

OK

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)
a.

Disconnect the certification ECU (smart key ECU assembly) connectors.


B342591C05
4.854,0.406 5.323,0.677 0.469,0.271 1.438,0.406 1.896,0.677 0.458,0.271 2.656,1.396 2.885,2.167 true 0.396,2.146 0.646,1.396 true 5.542,1.531 5.813,2.208 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.271,2.198 0.583,2.396 0.313,0.198 10 false +B 2.854,2.219 3.167,2.417 0.313,0.198 10 false E 5.698,2.281 6.281,2.469 0.583,0.188 10 false CUTB 4.979,0.458 5.438,0.656 0.458,0.198 10 false G17 1.552,0.458 2.031,0.656 0.479,0.198 10 false G16
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-10 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G17-33 (CUTB) - Body ground Always 11 to 14 V
G16-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

26.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the certification ECU (smart key ECU assembly) connectors.


b.

Check the entry lock/unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

NG

27.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
27.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

28.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
28.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

29.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.



Result:
Proceed to
OK
NG



OK

30.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

AFFECTED BY WAVE INTERFERENCE

30.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assembly B



A

31.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

32.CHECK KEY DIAGNOSTIC MODE
31.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

32.CHECK KEY DIAGNOSTIC MODE
32.CHECK KEY DIAGNOSTIC MODE
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G25 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-21 (CSEL) - G25-2 (CSEL) Always Below 1 Ω
G17-21 (CSEL) or G25-2 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the G17 certification ECU (smart key ECU assembly) connector.


b.

Connect the G25 door control receiver connector.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

35.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

35.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Using an oscilloscope, check the waveform.

B348668C12
1.625,0.469 2.052,0.698 0.427,0.229 2.615,2.177 2.167,1.25 true 1.906,2.177 2,1.271 true 0.76,0.5 1.073,0.698 0.313,0.198 10 false *a 3.854,0.583 4.167,0.781 0.313,0.198 10 false *b 2.49,2.219 2.802,2.417 0.313,0.198 10 false GND 1.719,2.219 2.198,2.417 0.479,0.198 10 false CSEL 3.667,1.333 3.979,1.531 0.313,0.198 10 false GND 1.719,0.5 2.031,0.698 0.313,0.198 10 false G25
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1


OK:
Tester Connection Condition Tool Setting Specified Condition
G25-2 (CSEL) - G25-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

36.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

36.CHECK DOOR CONTROL RECEIVER
a.

Using an oscilloscope, check the waveform.

HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


B327899C21
1.594,0.521 2.115,0.74 0.521,0.219 1.177,2.083 1.479,1.26 true 2.604,2.073 2.188,1.281 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.729,0.531 2.042,0.729 0.313,0.198 10 false G25 0.99,2.104 1.49,2.323 0.5,0.219 10 false DATA 2.458,2.104 2.958,2.323 0.5,0.219 10 false GND 3.719,1.198 4.219,1.417 0.5,0.219 10 false GND 3.875,0.115 4.188,0.313 0.313,0.198 10 false *b 4.406,1.927 4.719,2.125 0.313,0.198 10 false *c 5.385,1.938 5.698,2.135 0.313,0.198 10 false *d
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed


OK:
Tester Connection Condition Tool Setting Specified Condition
G25-5 (DATA) - G25-1 (GND) Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

37.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

37.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

38.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
38.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG