16027
1.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
| *1 | New Gasket |
Install a new gasket and No. 1 turbo water pipe sub-assembly with the bolt and 2 nuts.
17141
2.INSTALL EXHAUST MANIFOLD
Install a new gasket and the turbocharger sub-assembly with 3 new nuts to the exhaust manifold.
| *1 | New Gasket |
| *2 | Turbo Oil Inlet Pipe Sub-assembly |
| *a | Wide |
| *b | Narrow |
|
Outside |
Install a new gasket and the turbo oil inlet pipe sub-assembly with the 2 nuts, but only loosely install the nuts.
The notch (wide part) of the gasket must face the engine.
| *1 | Collar |
|
Engine Side |
Temporarily install the exhaust manifold with turbocharger sub-assembly, 8 collars and the 8 plate washers to the cylinder head sub-assembly with 8 new nuts.
Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.
| *1 | New Gasket |
| *2 | Turbo Oil Inlet Pipe Sub-assembly |
| *3 | Union Bolt |
| *a | Claw |
|
Turbo Oil Inlet Pipe Side |
Install a new gasket (labeled A) and the turbo oil inlet pipe sub-assembly with the 2 bolts, but only loosely install the bolts.
The claws of the gasket must face the turbo oil inlet pipe sub-assembly.
Install a new gasket (labeled B) and the turbo oil inlet pipe sub-assembly with the union bolt, but only loosely install the union bolt.
Tighten the exhaust manifold with turbocharger sub-assembly, to the cylinder head sub-assembly with 8 nuts.
Tighten the nuts in the order shown in the illustration.
Tighten the 2 nuts and union bolt of the turbo oil inlet pipe sub-assembly, and the 2 bolts.
Tighten the nut, union bolt and bolt in that order.
Install the 2 bolts and the nut of the turbocharger stay in the order shown in the illustration.
17291
3.INSTALL TURBINE OUTLET ELBOW
Install a new gasket and the turbine outlet elbow to the turbocharger sub-assembly with new 3 nuts.
16284
4.INSTALL NO. 1 TURBO WATER HOSE
Install the 2 No. 1 turbo water hoses to the No. 3 water by-pass pipe and cylinder block sub-assembly.
17167
5.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Temporarily install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the bolt.
17271
6.INSTALL NO. 1 TURBO INSULATOR
Temporarily install the No. 1 turbo insulator to the turbocharger sub-assembly with the 2 bolts.
Tighten the bolt of the No. 1 exhaust manifold heat insulator, and the 2 bolts of the No. 1 turbo insulator.
17274
7.INSTALL COMPRESSOR INLET ELBOW
Install a new gasket and the compressor inlet elbow to the turbocharger sub-assembly with the 2 nuts.
Connect the 2 connectors to the turbocharger sub-assembly.
Attach the wire harness clamp.
12229
8.INSTALL PCV PIPE
Connect the 2 PCV hoses to the cylinder head cover sub-assembly and compressor inlet elbow.
Install the PCV pipe to the cylinder head sub-assembly with the bolt.
17701
9.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Connect the 3 wire harness clamps.
17801
10.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
17705
11.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
Attach the 4 clips to install the air cleaner cap sub-assembly with air cleaner hose.
Tighten the hose clamp.
Connect the mass air flow meter connector and attach the 2 wire harness clamps.
17410
12.INSTALL FRONT EXHAUST PIPE ASSEMBLY
53882F
13.INSTALL FRONT FENDER SEAL
Install the front fender seal with new 6 clips.
53735B
14.INSTALL FRONT FENDER APRON SEAL UPPER
Install the front fender apron seal upper with new 5 clips.
17940D
15.INSTALL INTERCOOLER ASSEMBLY
16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
17.ADD ENGINE COOLANT
18.INSPECT FOR ENGINE COOLANT LEAK
19.INSPECT FOR OIL LEAK
20.INSPECT ENGINE OIL LEVEL
51442
21.INSTALL NO. 2 ENGINE UNDER COVER
51441
22.INSTALL NO. 1 ENGINE UNDER COVER
23.PERFORM INITIALIZATION