Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL INJECTOR › from 2016.01
RM3270E _51 Engine / Hybrid System _048940 2TR-FE FUEL _0243340 FUEL INJECTOR G

2TR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


Hide 23250 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injection volume.

CAUTION:
·

This test involves high-pressure fuel and electricity.

·

Take every precaution regarding safe handling of both the fuel and the electrical parts.

·

Perform this test in a safe area and avoid any sparks and flames.

·

Do not smoke.



i.
A269129C01
0.573,2.792 0.573,2.438 false 2.365,1.594 2.365,1.417 2.365,1.417 2.552,1.229 false 2.865,1.354 3.125,1.354 false 1.156,2.542 1.156,2.188 false 0.76,1.542 0.917,1.542 0.917,1.542 1.219,1.781 false 1.25,0.99 1.406,0.99 1.406,0.99 1.76,1.302 false 1.729,0.594 1.885,0.594 1.885,0.594 2.323,0.979 false 1.875,2.313 2.219,2.313 false 1.865,1.625 2.052,1.625 2.052,1.625 2.052,2.313 false 3.167,1.25 3.354,1.458 0.188,0.208 10 false *a 0.552,1.438 0.74,1.646 0.188,0.208 10 false *b 1.042,0.885 1.229,1.094 0.188,0.208 10 false *c 0.51,2.823 0.698,3.031 0.188,0.208 10 false *d 2.26,2.208 2.448,2.417 0.188,0.208 10 false *e 1.531,0.5 1.719,0.708 0.188,0.208 10 false *b 1.094,2.563 1.281,2.771 0.188,0.208 10 false *e 2.302,1.635 2.49,1.844 0.188,0.208 10 false *e
*a SST (Fuel Tube Connector)
*b SST (Hose)
*c SST (3 Way)
*d SST (Union No. 7)
*e SST (Hose Band)


Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41091, 09268-41120, 09268-41500, 09268-41700, 95336-08070)


ii.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION


iii.

Remove the No. 1 fuel hose from the fuel filter.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL FILTER>REPLACEMENT


iv.

Remove the 2 bolts and disconnect the fuel pressure regulator assembly from the fuel delivery pipe.

NOTICE:

Do not disconnect the No. 2 fuel hose from the fuel pressure regulator assembly.



v.
A264461C03
2.5,0.875 2.833,0.875 false 2.448,1.802 2.792,1.802 false 2.875,0.771 3.083,0.979 0.208,0.208 10 false *a 2.833,1.698 3.031,1.896 0.198,0.198 10 false *1
*1 Fuel Filter
*a SST (Fuel Tube Connector)


Connect SST to the fuel filter.

SST
09268-31014  (09268-41500)

CAUTION:

Always read the precautions before connecting the fuel tube connector (quick type).

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION



vi.
A337870C01
1.438,0.375 1.604,0.375 1.604,0.375 2.021,0.604 false 2.563,0.177 3.01,0.177 false 2.677,1.25 2.677,0.688 false 2.906,0.51 3.073,0.781 3.073,0.781 3.073,0.99 false 1.229,0.281 1.417,0.469 0.188,0.188 10 false *1 3,1.021 3.208,1.219 0.208,0.198 10 false *a 2.375,0.073 2.563,0.26 0.188,0.188 10 false *b 2.604,1.281 2.802,1.49 0.198,0.208 10 false *c
*1 Fuel Pressure Regulator Assembly
*a SST (Hose Band)
*b SST (Hose)
*c SST (Union No. 7)


Connect SST to the fuel pressure regulator assembly with the 2 bolts.

SST
09268-31014  (09268-41091, 09268-41700, 95336-08070)

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


vii.

Install the O-ring to the fuel injector assembly.


viii.
A264463C03
1.052,0.156 1.448,0.156 false 1.042,0.49 1.417,0.49 false 1.771,0.292 2.146,0.292 false 2.5,1.271 2.875,1.271 false 1.094,1.979 1.469,1.979 false 2.188,0.188 2.406,0.375 0.219,0.188 10 false *a 0.844,0.385 1.063,0.594 0.219,0.208 10 false *b 0.844,0.052 1.052,0.24 0.208,0.188 10 false *c 2.917,1.167 3.115,1.365 0.198,0.198 10 false *d 0.896,1.865 1.104,2.073 0.208,0.208 10 false *e
*a SST (Hose Band)
*b SST (Adaptor)
*c SST (Hose)
*d SST (Clamp)
*e Vinyl Tube


Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41110, 09268-41310, 09268-41700, 95336-08070)

NOTICE:

Make sure that SST (adapter) and SST (clamp) are not loose and do not rattle.



ix.
A264464C03
1.396,1.646 1.781,2.01 1.781,2.01 1.958,2.01 true 2.469,0.875 2.469,1.115 2.469,1.115 2.656,1.115 true 2,1.896 2.219,2.094 0.219,0.198 10 false *a 2.688,1.01 3.031,1.229 0.344,0.219 10 false *b
*a SST (Tie Band)
*b Lock


Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



x.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


xi.

Install a vinyl tube to the fuel injector assembly.


xii.

Put the fuel injector assembly into a graduated cylinder.

NOTICE:

Install a suitable vinyl tube to the injector to contain any gasoline spray.




xiv.
A302983C04
1.844,0.708 1.844,0.375 false 1.802,0.74 2.115,0.938 0.313,0.198 10 false *a
*a SST (EFI Inspection Wire H)
V100135

Connect


Connect SST (EFI inspection wire H) to the fuel injector assembly and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

82 to 99 cc (5.0 to 6.0 cu in.) per 15 seconds


Difference between each injector:

17 cc (1.0 cu in.) or less


If the result is not as specified, replace the fuel injector assembly.



b.

Check the leakage.

i.

In the condition above, disconnect the test probes of SST (EFI inspection wire H) from the battery and check the fuel leakage rate from the fuel injector assembly.

Fuel leakage:

1 drop or less per 25 minutes