Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE › from 2016.01
RM3270E _51 Engine / Hybrid System _048947 1GR-FE ENGINE MECHANICAL _0243421 ENGINE G

1GR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.


PROCEDURE

Hide 16361A 4.INSPECT FAN AND GENERATOR V BELT

Hide 16620 5.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

Hide 17801 6.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


b.

Check that the air cleaner filter element sub-assembly is not excessively dirty.

If the air cleaner filter element sub-assembly is excessively dirty, replace the air cleaner filter element sub-assembly.

If cleaning the air cleaner filter element sub-assembly, blow compressed air to clean it.

NOTICE:
·

Do not start the engine with the air cleaner filter element sub-assembly removed, as this may damage the engine.

·

When using an air cleaner filter element sub-assembly that uses compressed air, wear safety glasses and a dust mask in order to protect your health.



HINT:

When an excessive amount of dirt is present, replace the air cleaner filter element sub-assembly.



c.

Reinstall the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 8.INSPECT IGNITION TIMING

a.

Warm up the engine and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.

NOTICE:

Switch off all the accessories and the A/C before connecting the GTS.



ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1.

Powertrain > Engine > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

v.

Inspect the ignition timing during idling.

Standard ignition timing:

8 to 12° BTDC @ idle


NOTICE:

When checking the ignition timing, the transmission should be in N or P.


HINT:

Refer to the GTS operator's manual for further details.



vi.

Cancel the Active Test.


vii.

Enter the following menus: Powertrain / Engine / Data List / IGN Advance.

Powertrain > Engine > Data List
Tester Display
IGN Advance
50003 234 29

viii.

Inspect the ignition timing during idling.

Standard ignition timing:

7 to 24° BTDC @ idle


NOTICE:

When checking the ignition timing, the transmission should be in N or P.



ix.

Check that the ignition timing advances immediately when the engine speed is increased.



c.

When not using the GTS:

i.
A206183C78
1.188,0.531 1.385,0.531 1.385,0.531 1.594,0.906 true 1.771,1.469 1.906,1.865 1.906,1.865 2.125,1.865 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 0.958,0.458 1.271,0.656 0.313,0.198 10 false CG 2.177,1.802 2.49,2 0.313,0.198 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not improperly connect the terminals. This may damage the engine.



ii.

Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

NOTICE:
·

Use a timing light that detects primary signals.

·

After checking, be sure to wrap the wire harness with tape.




iii.

Start the engine.


iv.

Inspect the ignition timing during idling.

Standard ignition timing:

8 to 12° BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the ignition timing, the transmission should be in N or P.




v.

Remove SST from the DLC3.


vi.

Inspect the ignition timing during idling.

Standard ignition timing:

7 to 24° BTDC @ idle



vii.

Disconnect the timing light from the wire of the ignition coil connector for the No. 1 cylinder.



Hide 9.INSPECT ENGINE IDLE SPEED

a.

Warm up the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.

NOTICE:

Switch off all accessories and the A/C before connecting the GTS.



ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9

v.

Inspect the engine idle speed.

Standard idle speed:

650 to 750 rpm


NOTICE:

When checking the idle speed, the transmission should be in N or P.


HINT:

Refer to the GTS operator's manual for further details.



vi.

Turn the ignition switch off.


vii.

Disconnect the GTS from the DLC3.



c.

When not using the GTS:

i.
A206183C80
0.583,1.896 0.771,1.896 0.771,1.896 1,1.479 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 0.281,1.813 0.594,2.01 0.313,0.198 10 false TAC
*a Front view of DLC3


Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:

Switch off all accessories and the A/C before connecting the terminals.



ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Inspect the engine idle speed.

Standard idle speed:

650 to 750 rpm


NOTICE:

When checking the idle speed, the transmission should be in N or P.



iv.

Disconnect the tachometer tester probe from the DLC3.



Hide 10.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Check for DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

c.

Drain the engine coolant.

Click hereEngine / Hybrid System>1GR-FE COOLING>COOLANT>REPLACEMENT


d.


f.

Disconnect the 6 fuel injector connectors.

NOTICE:

Stop fuel injection to prevent damage to the catalyst due to unburned fuel.



g.

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

While cranking the engine, measure the compression pressure.

Compression pressure:

1300 kPa (13.3 kgf/cm2, 189 psi) or higher


Minimum pressure:

1000 kPa (10.2 kgf/cm2, 145 psi)


Difference between each cylinder:

100 kPa (1.0 kgf/cm2, 15 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression in as short a time as possible.




iii.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, and then inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.





h.

Connect the 6 fuel injector connectors.



j.


l.

Check for DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

Hide 11.INSPECT CO/HC

a.

Start and warm up the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds, and then idle the engine.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe.


d.

Check the CO/HC concentration at idle.

Standard idle CO concentration:

0 to 0.5%


Standard idle HC concentration:

Refer to applicable local regulation



e.

If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

i.

Check the air fuel ratio sensor operation.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION


ii.

Check the heated oxygen sensor operation.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION


iii.

See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

CO HC Problem Possible Cause
Normal High Rough idling
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaky intake and exhaust valves

4.

Leaky cylinders


Low High Rough idling
(Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body with motor assembly

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idling
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve sub-assembly

3.

Faulty SFI system:

·

Faulty fuel pressure regulator assembly

·

Defective engine coolant temperature sensor

·

Defective intake mass air flow meter sub-assembly

·

Faulty ECM

·

Faulty fuel injector assemblies

·

Faulty throttle body with motor assembly