Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL PUMP › from 2016.01
RM3270E _51 Engine / Hybrid System _048952 1GR-FE LUBRICATION _0243451 OIL PUMP A

1GR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 11301M 3.REMOVE VVT SENSOR (for Bank 1)

Hide 11301M 4.REMOVE VVT SENSOR (for Bank 2)

Hide 15330B 5.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)

Hide 15340 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

Hide 11452 8.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16031 9.REMOVE WATER INLET ASSEMBLY

Hide 16620 10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16604 11.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16603 12.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 13471 13.REMOVE CRANKSHAFT PULLEY

a.
A343628C01
2.083,1.75 1.833,1.75 1.833,1.75 1.417,0.917 true 1.333,1.083 1.833,1.75 true 2.167,1.667 2.625,1.865 0.458,0.198 10 false SST 3,0.583 3.333,0.833 0.333,0.25 10 false *a 1.25,1.917 1.667,2.083 0.417,0.167 10 false *b
*a Hold
*b Loosen


Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Screw the crankshaft pulley set bolt into the crankshaft by 2 or 3 threads.


c.
A343629C01
1.24,1.396 1.49,1.396 false 2.01,1.479 2.208,1.479 2.208,1.479 2.208,1.063 true 0.958,1.333 1.417,1.531 0.458,0.198 10 false SST 0.177,2.01 0.635,2.208 0.458,0.198 10 false *a 2.469,3.177 2.927,3.375 0.458,0.198 10 false *b 1.833,1.396 2.292,1.594 0.458,0.198 10 false *1
*1 Crankshaft Pulley Set Bolt
*a Hold
*b Turn


Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley and crankshaft pulley set bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031)


Hide 12102A 14.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A251899C01
1.708,1.958 1.74,1.927 false
V100135

Bolt
V100136

Nut


Remove the 14 bolts and 2 nuts.


b.
A112957C01
1.5,1.667 1.333,1.667 1.333,1.667 1,1.083 true 1.552,1.583 1.865,1.781 0.313,0.198 10 false *a
*a Oil Pan Seal Cutter


Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.

·

Be careful not to damage the flange of the No. 2 oil pan sub-assembly.




Hide 15104 15.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A112955

Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.


Hide 12101 16.REMOVE OIL PAN SUB-ASSEMBLY

a.
A251900C01
0.656,1.885 0.667,1.938 false
V100135

Bolt
V100136

Nut


Remove the 17 bolts and 2 nuts.


b.
A343630C01
1.75,1.5 1.583,1.5 1.583,1.5 1.469,0.938 false 1.802,1.406 2.115,1.604 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A343631

Remove the O-ring from the timing chain cover sub-assembly.


Hide 23801P 17.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A343632C01
1.198,1.24 1.354,1.438 0.156,0.198 10 false .
V100135

Bolt
V100136

Nut


Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover sub-assembly and cylinder head cover gasket.


Hide 11202 19.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A343633C01
1.26,1.344 1.417,1.542 0.156,0.198 10 false .
V100135

Bolt
V100136

Nut


Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover sub-assembly LH and cylinder head cover gasket.


Hide 15601 20.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15609 21.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
A251960C01
1.135,1.698 1.208,1.656 false
V100135

Bolt
V100136

Nut


Remove the 3 bolts, 2 nuts, oil filter bracket sub-assembly and gasket.


Hide 11302 22.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A251901C01
0.844,2.604 0.896,2.594 false
V100135

Bolt
V100136

Nut


Remove the 24 bolts and 2 nuts.


b.
A343634C01
1.5,0.167 1.667,0.167 1.667,0.167 1.958,0.667 true 1.344,3.115 1.094,3.115 1.094,3.115 0.51,2.781 true 2.781,2.792 2.333,3.167 2.333,3.167 2.167,3.167 true 2.646,1.448 2.646,0.365 2.646,0.365 2.813,0.365 true 1.302,0.083 1.615,0.281 0.313,0.198 10 false *a 1.385,3.031 1.698,3.229 0.313,0.198 10 false *a 1.979,3.083 2.292,3.281 0.313,0.198 10 false *a 2.844,0.292 3.094,0.458 0.25,0.167 10 true *a
*a Protective Tape


Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the timing chain cover sub-assembly, cylinder block sub-assembly and cylinder head sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A134563

Remove the O-ring from the cylinder head LH.


Hide 11303A 23.REMOVE FRONT CRANKSHAFT OIL SEAL

a.

Using a screwdriver and wooden block, pry out the front crankshaft oil seal.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Do not damage the surface of the oil seal press fit hole and crankshaft.