The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the engine assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly may fall off the engine lifter.
To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.
Do not remove the radiator cap sub-assembly,cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.DRAIN ENGINE COOLANT
5.DRAIN ENGINE OIL
53301
6.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose.
Remove the 4 bolts and hood sub-assembly.
11259
7.REMOVE V-BANK COVER
51410
8.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51442
9.REMOVE NO. 2 ENGINE UNDER COVER
51407A
10.REMOVE NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY
11.DRAIN DIFFERENTIAL OIL (for 4WD)
53735B
12.REMOVE FRONT UPPER FENDER APRON SEAL LH
Remove the 6 clips and front upper fender apron seal LH.
53735B
13.REMOVE FRONT UPPER FENDER APRON SEAL RH
Remove the 6 clips and front upper fender apron seal RH.
53882F
14.REMOVE FRONT FENDER SEAL LH
Remove the 6 clips and front fender seal LH.
53882F
15.REMOVE FRONT FENDER SEAL RH
Remove the 6 clips and front fender seal RH.
53294C
16.REMOVE RADIATOR SIDE DEFLECTOR LH
53293C
17.REMOVE RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
17705
18.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
17801
19.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
20.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Disconnect the 3 clamps from the air cleaner case sub-assembly.
Remove the 3 bolts and air cleaner case sub-assembly.
16593
21.REMOVE NO. 1 RADIATOR AIR GUIDE
16571
22.REMOVE RADIATOR HOSE INLET
16572
23.REMOVE RADIATOR HOSE OUTLET
16470
24.REMOVE RADIATOR RESERVOIR
16711
25.REMOVE FAN SHROUD
32941
26.DISCONNECT NO. 1 OIL COOLER INLET HOSE
32942
27.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE
16400
28.REMOVE RADIATOR ASSEMBLY
44320
29.DISCONNECT VANE PUMP ASSEMBLY
Disconnect the connector.
Remove the 2 bolts and disconnect the vane pump assembly.
Do not hit other parts with the pulley when disconnecting the vane pump assembly.
Be sure to suspend the vane pump assembly securely.
17129
30.REMOVE INTAKE AIR SURGE TANK
17450B
31.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
17410
32.REMOVE FRONT EXHAUST PIPE ASSEMBLY
17118
33.REMOVE MANIFOLD STAY
17104
34.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
17119
35.REMOVE NO. 2 MANIFOLD STAY
17105
36.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
28100
37.REMOVE STARTER ASSEMBLY
11363A
38.REMOVE FLYWHEEL HOUSING SIDE COVER
55607
39.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Cover)
55550
40.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
89661
41.REMOVE ECM
82121
42.DISCONNECT ENGINE WIRE (for LHD)
Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.
Disconnect the connector.
Remove the bolt and disconnect the engine wire.
Detach the clamp and disconnect the engine wire from the bracket.
Detach the grommet and pull out the engine wire from the cabin.
Remove the nut and disconnect the engine room main wire from the battery positive cable.
Loosen the nut and remove the positive (+) battery terminal.
Loosen the 2 nuts and remove the battery hold down clamp.
Remove the battery.
Remove the battery tray.
Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.
Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.
Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.
Remove the nut and disconnect the engine wire from the engine room relay block.
Disconnect the 2 connectors from the engine room relay block.
82121
43.DISCONNECT ENGINE WIRE (for RHD)
Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.
Disconnect the connector.
Remove the bolt and disconnect the engine wire.
Detach the clamp and disconnect the engine wire from the bracket.
Detach the grommet and pull out the engine wire from the cabin.
Remove the nut and disconnect the engine room main wire from the battery positive cable.
Loosen the nut and remove the positive (+) battery terminal.
Loosen the 2 nuts and remove the battery hold down clamp.
Remove the battery.
Remove the battery tray.
Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.
Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.
Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.
Remove the nut and disconnect the engine wire from the engine room relay block.
Disconnect the 2 connectors from the engine room relay block.
27020
44.REMOVE GENERATOR ASSEMBLY
for 115A Type:
Click herePower Source / Network>1GR-FE BATTERY / CHARGING>GENERATOR(for 115A Type)>REMOVAL
for 100A Type:
Click herePower Source / Network>1GR-FE BATTERY / CHARGING>GENERATOR(for 100A Type)>REMOVAL
88320
45.DISCONNECT COOLER COMPRESSOR ASSEMBLY
46.REMOVE WATER HOSE SUB-ASSEMBLY
Slide the 4 clamps and remove the water hose sub-assembly.
23801P
47.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY
23802B
48.DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY
Slide the clamp and disconnect the No. 2 fuel pipe sub-assembly.
51561D
49.REMOVE PROPELLER SHAFT GUARD (for 4WD)
37140
50.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made)>REMOVAL
except TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(except TSAM Made)>REMOVAL
43514C
51.REMOVE FRONT AXLE HUB GREASE CAP (for 4WD)
43502H
52.REMOVE FRONT AXLE SHAFT NUT (for 4WD)
89543
53.DISCONNECT FRONT SPEED SENSOR LH (for 4WD)
89542
54.DISCONNECT FRONT SPEED SENSOR RH (for 4WD)
Use the same procedure described for the LH side.
55.DISCONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)
56.DISCONNECT TIE ROD END SUB-ASSEMBLY RH (for 4WD)
Use the same procedure described for the LH side.
48069
57.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for 4WD)
48068
58.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for 4WD)
Use the same procedure described for the LH side.
43420
59.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)
43410D
60.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)
43410
61.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)
Use the same procedure described for the LH side.
45219
62.DISCONNECT STEERING SLIDING YOKE (for 4WD)
63.REMOVE POWER STEERING LINK ASSEMBLY (for 4WD)
41110F
64.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
51569
65.REMOVE PROPELLER SHAFT GUARD
37100
66.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>REMOVAL
for TMT Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMT Made)>REMOVAL
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>REMOVAL
37100
67.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>REMOVAL
for TMT Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMT Made)>REMOVAL
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>REMOVAL
68.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
35000
69.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
32101
70.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
71.INSTALL ENGINE HANGER
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger with 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-31060 |
| No. 2 Engine Hanger | 12282-31040 |
| Bolt | 90119-08A87 |
11000
72.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine with a chain block.
Remove the 4 bolts and 4 nuts from the body.
Remove the engine assembly by operating the engine sling device and chain block.
Make sure that the engine is clear of all wiring and hoses.
While lowering the engine from the vehicle, do not allow it to contact the vehicle.
11000
73.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine to an engine stand with bolts.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.