Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › from 2016.01
RM3270E _52 Drivetrain _041680 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0239142 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the L4 detection switch.

This DTC indicates that the L4 detection switch remains on.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance L4 detection switch remains on while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in H2 or H4.
·

Short in L4 detection switch circuit

·

Skid control ECU (brake actuator assembly)

·

4 wheel drive control ECU

·

Transfer shift actuator assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the L4 detection switch to determine when the transfer case L4 gears are engaged. If the transfer case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 detection switch, illuminate the MIL and store the DTC:

·

The L4 detection switch indicates that the L4 transfer case gears are engaged.

·

The transfer position switch is in H2 or H4.

·

The transfer case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C325306E15
2.427,0.854 3.406,1.042 0.979,0.188 10 false EXI2*1, EXI4*2 3.5,0.958 3.802,1.156 0.302,0.198 10 false A68 3.927,0.958 4.229,1.156 0.302,0.198 10 false A4 3.938,1.219 4.24,1.417 0.302,0.198 10 false *2 3.563,1.208 3.865,1.406 0.302,0.198 10 false *1 3.583,0.75 3.885,0.948 0.302,0.198 10 false 8 3.979,0.76 4.281,0.958 0.302,0.198 10 false 5 1.115,1.844 4.104,2.031 2.99,0.188 10 false Skid Control ECU (Brake Actuator Assembly) 1.625,3.833 3.365,4.052 1.74,0.219 10 false 4 Wheel Drive Control ECU 6.031,5.104 6.49,5.313 0.458,0.208 10 false G144 2.979,3 3.552,3.188 0.573,0.188 10 false 4WDL 5.531,4.458 5.813,4.656 0.281,0.198 10 false L4 3.479,2.99 3.635,3.167 0.156,0.177 10 false 3 3.938,4.438 4.094,4.615 0.156,0.177 10 false 9 1.344,4.427 1.635,4.604 0.292,0.177 10 false 10 1.688,4.438 2.052,4.635 0.365,0.198 10 false GND 1.698,5.24 4.01,5.458 2.313,0.219 10 false Transfer Shift Actuator Assembly 1.677,5.083 2.01,5.271 0.333,0.188 10 false C74 3.594,4.438 3.875,4.635 0.281,0.198 10 false L4 5.323,4.448 5.563,4.635 0.24,0.188 10 false 8 6.063,5.271 6.448,5.51 0.385,0.24 10 false ECM 1.604,3.667 1.938,3.854 0.333,0.188 10 false C60 2.531,0.302 2.969,0.479 0.438,0.177 10 false 12 V 2.74,2.51 3.177,2.688 0.438,0.177 10 false 12 V 6.323,3.573 6.76,3.75 0.438,0.177 10 false 12 V 2.125,4.729 3.531,4.938 1.406,0.208 10 false L4 Detection Switch 0.198,5.146 1.135,5.354 0.938,0.208 10 false *1: w/o VSC 0.198,5.427 1.135,5.635 0.938,0.208 10 false *2: w/ VSC

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the transfer position switch to H2.



PROCEDURE

1.CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.
C325305C08
1.49,0.344 1.813,0.542 0.323,0.198 1.479,2.635 1.802,2.833 0.323,0.198 1.833,1.104 2.281,0.427 true 1.333,3.385 1.115,2.76 true 0.115,0.219 0.427,0.375 0.313,0.156 10 false *a 0.344,0.448 0.656,0.604 0.313,0.156 10 false *A 0.365,2.75 0.677,2.906 0.313,0.156 10 false *B 2.344,0.344 2.823,0.563 0.479,0.219 10 false EXI2 0.76,2.594 1.24,2.813 0.479,0.219 10 false EXI4 1.521,0.354 1.833,0.552 0.313,0.198 10 false A68 1.552,2.646 1.865,2.844 0.313,0.198 10 false A4
*A w/o VSC
*B w/ VSC
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A68*1 or A4*2 skid control ECU (brake actuator assembly) connector.

*1: w/o VSC

*2: w/ VSC


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o VSC
Tester Connection Switch Condition Specified Condition
A68-8 (EXI2) - Body ground Transfer position switch not L4 10 kΩ or higher

w/ VSC
Tester Connection Switch Condition Specified Condition
A4-5 (EXI4) - Body ground Transfer position switch not L4 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY
2.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY
a.
C325622C25
1.458,0.646 1.833,0.896 0.375,0.25 1.521,1.99 0.875,2.615 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.521,0.677 1.979,0.875 0.458,0.198 10 false C74 0.781,2.656 1.24,2.854 0.458,0.198 10 false L4
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)


Disconnect the C74 transfer shift actuator assembly connector.


b.

Disconnect the A68*1 or A4*2 skid control ECU (brake actuator assembly) connector.

*1: w/o VSC

*2: w/ VSC


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C74-9 (L4) - Body ground Transfer position switch not L4 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

3.CHECK 4 WHEEL DRIVE CONTROL ECU
3.CHECK 4 WHEEL DRIVE CONTROL ECU
a.
C136763C09
1.49,0.635 1.875,0.896 0.385,0.26 0.75,1.677 0.552,0.865 true 1.563,0.677 2.021,0.875 0.458,0.198 10 false C60 0.323,0.688 0.802,0.865 0.479,0.177 10 false 4WDL 0.156,0.167 0.635,0.427 0.479,0.26 10 false *a
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the C60 4 wheel drive control ECU connector.


b.

Disconnect the C74 transfer shift actuator assembly connector.


c.

Disconnect the A68*1 or A4*2 skid control ECU (brake actuator assembly) connector.

*1: w/o VSC

*2: w/ VSC


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C60-3 (4WDL) - Body ground Transfer position switch not L4 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY), TRANSFER SHIFT ACTUATOR ASSEMBLY, 4 WHEEL DRIVE CONTROL ECU - ECM)
4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY), TRANSFER SHIFT ACTUATOR ASSEMBLY, 4 WHEEL DRIVE CONTROL ECU - ECM)
a.
C329166C06
0.292,0.271 0.708,0.49 0.417,0.219 0.813,2.042 1.313,2.469 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.323,0.292 0.781,0.49 0.458,0.198 10 false G144 1.354,2.5 1.823,2.688 0.469,0.188 10 false 8 (L4)
*a Rear view of wire harness connector
(to ECM)


Disconnect the G144 ECM connector.


b.

Disconnect the C60 4 wheel drive control ECU connector.


c.

Disconnect the C74 transfer shift actuator assembly connector.


d.

Disconnect the A68*1 or A4*2 skid control ECU (brake actuator assembly) connector.

*1: w/o VSC

*2: w/ VSC


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G144-8 (L4) - Body ground Transfer position switch not L4 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR