Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2016.01
RM3270E _59 Vehicle Exterior _041720 LIGHTING (EXT) _0199661 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH  B2431  LED Headlight RH  


DESCRIPTION

The illumination of the low beam headlights is controlled by the body ECU. When the headlights are turned on, the headlight leveling ECU assembly receives a signal from the headlight assembly and detects the illumination condition of the low beam headlights.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2430 LED Headlight LH Low beam headlight LH malfunction
·

Headlight assembly LH

·

Headlight leveling ECU assembly

·

Body ECU

·

Instrument panel junction block assembly

·

Headlight relay (H-LP)

·

Harness or connector


B2431 LED Headlight RH Low beam headlight RH malfunction
·

Headlight assembly RH

·

Headlight leveling ECU assembly

·

Body ECU

·

Instrument panel junction block assembly

·

Headlight relay (H-LP)

·

Harness or connector



HINT:

DTC B2430 and B2431 are not output if 12 seconds have not elapsed since the ignition switch was turned to ON.


WIRING DIAGRAM

E317293E03
0.333,0.323 2.167,0.521 1.833,0.198 10 false from Battery 1.365,0.51 3.198,0.708 1.833,0.198 10 false H-LP MAIN 2.469,0.24 4.094,0.49 1.625,0.25 10 false 3 2.469,0.563 4.094,0.813 1.625,0.25 10 false 1 3.271,0.563 4.896,0.813 1.625,0.25 10 false 2 3.271,0.219 4.896,0.469 1.625,0.25 10 false 5 4.188,0.573 5.813,0.823 1.625,0.25 10 false 4 5.344,0.573 6.969,0.823 1.625,0.25 10 false 16 5.635,0.542 6.469,0.781 0.833,0.24 10 false HRLY 3.927,1.229 5.531,1.594 1.604,0.365 10 false Instrument Panel Junction Block Assembly 3.927,1.083 4.76,1.323 0.833,0.24 10 false 2Q 5.646,2.031 6.479,2.302 0.833,0.271 10 false A 5.656,2.208 6.448,2.479 0.792,0.271 10 false Body ECU 2.979,2.906 4.813,3.104 1.833,0.198 10 false H-LP LH-LO 2.333,2.896 3.958,3.146 1.625,0.25 10 false 1 2.333,3.26 3.99,3.49 1.656,0.229 10 false 4 2,2.615 3.833,2.813 1.833,0.198 10 false LO 2.073,2.896 3.906,3.094 1.833,0.198 10 false E 2.094,3.25 3.927,3.448 1.833,0.198 10 false S 0.563,3.927 2.396,4.125 1.833,0.198 10 false A57 0.573,4.104 2.99,4.344 2.417,0.24 10 false Headlight Assembly LH 2.031,4.854 3.865,5.052 1.833,0.198 10 false LO 2.104,5.458 3.938,5.656 1.833,0.198 10 false S 2.115,5.115 3.948,5.313 1.833,0.198 10 false E 2.333,2.615 3.958,2.865 1.625,0.25 10 false 3 2.344,4.813 3.969,5.063 1.625,0.25 10 false 3 2.344,5.115 3.969,5.365 1.625,0.25 10 false 1 2.344,5.458 4,5.688 1.656,0.229 10 false 4 2.969,5.146 4.802,5.344 1.833,0.198 10 false H-LP RH-LO 0.625,5.417 2.458,5.615 1.833,0.198 10 false Low/High 0.469,6.177 2.302,6.375 1.833,0.198 10 false A56 0.479,6.323 2.573,6.521 2.094,0.198 10 false Headlight Assembly RH 5.531,3.219 6.052,3.458 0.521,0.24 10 false 3 5.542,5.427 6.063,5.667 0.521,0.24 10 false 2 5.74,3.365 6.26,3.604 0.521,0.24 10 false LLEW 5.76,5.573 6.281,5.813 0.521,0.24 10 false RLEW 5.552,6.021 6.073,6.26 0.521,0.24 10 false G40 5.552,6.177 7.021,6.5 1.469,0.323 10 false Headlight Leveling ECU Assembly 2.813,1 4.646,1.198 1.833,0.198 10 false H-LP 0.625,3.188 2.458,3.385 1.833,0.198 10 false Low/High

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

When replacing the headlight leveling ECU assembly, be sure to initialize the automatic light control system.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION



HINT:

If DTC B2416 and/or B241A (Automatic Headlight Beam Level Control System) is output at the same time as DTC B2430 and/or B2431, perform troubleshooting for DTC B2416 and/or B241A (Automatic Headlight Beam Level Control System) first.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361

Result:
Result Proceed to
DTC B2430 and B2431 are not output. A
DTC B2430 and B2431 are output. B
DTC B2430 or B2431 is output. C



A

B

3.INSPECT HEADLIGHT RELAY (H-LP)

C

9.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - HEADLIGHT ASSEMBLY)
3.INSPECT HEADLIGHT RELAY (H-LP)
a.
E317295N01
1.771,1.094 2.104,1.094 true 2.813,1.083 3.083,1.083 true 2.49,0.729 2.49,0.438 true 2.49,1.719 2.49,1.427 true 1.646,1.01 1.781,1.177 0.135,0.167 10 false 3 3.146,1.01 3.281,1.177 0.135,0.167 10 false 5 2.458,0.229 2.594,0.396 0.135,0.167 10 false 1 2.458,1.75 2.594,1.917 0.135,0.167 10 false 2

Remove the headlight relay (H-LP) from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - BATTERY)

NG

REPLACE HEADLIGHT RELAY (H-LP)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - BATTERY)
a.
E317294C01
0.115,0.135 0.292,0.323 0.177,0.188 10 false *a
*a Front view of wire harness connector
(to Headlight Relay [H-LP])


Remove the headlight relay (H-LP) from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay (H-LP) terminal 3 - Body ground Always 11 to 14 V
Headlight relay (H-LP) terminal 1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - HEADLIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - HEADLIGHT ASSEMBLY)
a.

Remove the headlight relay (H-LP) from the engine room relay block assembly.


b.

Disconnect the A57*1 or A56*2 headlight assembly connector.


*1: for LH Side

*2: for RH Side


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay (H-LP) terminal 5 - A57-3 (LO)*1 Always Below 1 Ω
Headlight relay (H-LP) terminal 5 - A56-3 (LO)*2 Always Below 1 Ω
Headlight relay (H-LP) terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight relay (H-LP) from the engine room relay block assembly.


b.

Disconnect the 2Q instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay (H-LP) terminal 2 - 2Q-4 Always Below 1 Ω
Headlight relay (H-LP) terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E317296N01
1.51,0.271 1.844,0.49 0.333,0.219 1.531,1.865 1.865,2.083 0.333,0.219 1.188,2.51 1.354,3.042 1.354,3.042 1.531,3.042 true 1.583,0.302 1.802,0.469 0.219,0.167 10 false 2Q 1.646,1.885 1.781,2.052 0.135,0.167 10 false A 1.583,2.969 1.979,3.135 0.396,0.167 10 false HRLY

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the body ECU from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (HRLY) - 2Q-4 Always Below 1 Ω



Result:
Result
OK
NG



OK

8.CHECK BODY ECU

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.CHECK BODY ECU
a.

Disconnect the A57*1 or A56*2 headlight assembly connector.


*1: for LH Side

*2: for RH Side


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-3 (LO) - Body ground Headlight dimmer switch (light control switch) in head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - HEADLIGHT ASSEMBLY)
a.

Remove the headlight relay (H-LP) from the engine room relay block assembly.


b.

Disconnect the A57*1 or A56*2 headlight assembly connector.

*1: for LH Side

*2: for RH Side



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side (B2430):
Tester Connection Condition Specified Condition
Headlight relay (H-LP) terminal 5 - A57-3 (LO) Always Below 1 Ω
Headlight relay (H-LP) terminal 5 - Body ground Always 10 kΩ or higher

for RH Side (B2431):
Tester Connection Condition Specified Condition
Headlight relay (H-LP) terminal 5 - A56-3 (LO) Always Below 1 Ω
Headlight relay (H-LP) terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the A57*1 or A56*2 headlight assembly connector.

*1: for LH Side

*2: for RH Side



b.

Disconnect the G40 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side (B2430):
Tester Connection Condition Specified Condition
A57-4 (S) - G40-3 (LLEW) Always Below 1 Ω
A57-1 (E) - Body ground Always Below 1 Ω
A57-4 (S) - Body ground Always 10 kΩ or higher

for RH Side (B2431):
Tester Connection Condition Specified Condition
A56-4 (S) - G40-2 (RLEW) Always Below 1 Ω
A56-1 (E) - Body ground Always Below 1 Ω
A56-4 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK RH HEADLIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK RH HEADLIGHT ASSEMBLY
a.

Temporarily replace the headlight assembly with a new or normally functioning one.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL


b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361

Result:
Result Proceed to
DTC B2430 and B2431 are not output. A
DTC B2430 or B2431 is output. B



A

END (HEADLIGHT ASSEMBLY WAS DEFECTIVE)

B

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY