When the vehicle is stopped, mode switching may be unavailable depending on the phase of the transfer assembly and A.D.D. actuator powertrain. There is no malfunction if mode switching is available after the vehicle is moved.
Confirm the problem symptoms.
| Result | Proceed to |
|---|---|
| The 4WD indicator light (green) is blinking* | A |
| The 4LO indicator light is blinking* | B |
*: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
A
B
Lift up the vehicle until all four wheels are off the ground.
for Automatic Transmission:
Move the shift lever to N.
for Manual Transmission:
Move the shift lever to neutral.
Turn the transfer position switch from H2 to H4.
The 4WD indicator light (green) continues to blink*.
*: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
Release the parking brake.
Turn the ignition switch off.
Disconnect the C74 transfer shift actuator assembly connector.
| *a | Component without harness connected
(Transfer Shift Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
Check that the terminals of the limit switch, 4WD detection switch and L4 detection switch of the transfer shift actuator assembly (TL1, TL2, TL3, B and L4) are in the condition shown in the table below (H4).
| Terminal | When H4 |
|---|---|
| TL1 | OFF (OPEN) |
| TL2 | OFF (OPEN) |
| TL3 | ON (GND) |
| B | ON (GND) |
| L4 | OFF (OPEN) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (TL1) - 6 (GND1) | Transfer H4 | 10 kΩ or higher |
| 4 (TL2) - 6 (GND1) | 10 kΩ or higher | |
| 5 (TL3) - 6 (GND1) | Below 1 Ω | |
| 12 (B) - 10 (GND) | Below 1 Ω | |
| 9 (L4) - 10 (GND) | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (H4 condition) | A |
| NG (not H4 condition) | B |
A
B
| *a | Component without harness connected
(A.D.D. Actuator (Differential Motor Actuator Assembly)) |
Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (DM1) - 2 (DM2) | Always | 1.5 to 10 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C61 4 wheel drive control ECU connector.
Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C61-2 (DM1) - C57-1 (DM1) | Always | Below 1 Ω |
| C61-6 (DM2) - C57-2 (DM2) | Always | Below 1 Ω |
| C61-2 (DM1) or C57-1 (DM1) - C61-6 (DM2) or C57-2 (DM2) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C60 4 wheel drive control ECU connector.
Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.
w/o VSC:
Disconnect the A68 skid control ECU (brake actuator assembly) connector.
w/ VSC:
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C60-8 (DL1) - C57-6 (DL1) | Always | Below 1 Ω |
| C60-7 (DL2) - C57-5 (DL2) | Always | Below 1 Ω |
| C60-2 (ADD) - C57-3 (ADD) | Always | Below 1 Ω |
| C57-4 (GND) - Body ground | Always | Below 1 Ω |
| C60-8 (DL1) or C57-6 (DL1) - Body ground | Always | 10 kΩ or higher |
| C60-7 (DL2) or C57-5 (DL2) - Body ground | Always | 10 kΩ or higher |
| C60-2 (ADD) or C57-3 (ADD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the A.D.D. actuator (differential motor actuator assembly).
Click hereDrivetrain>AXLE AND DIFFERENTIAL>AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR>REMOVAL
Check the limit switch and A.D.D. position switch of the A.D.D. actuator (differential motor actuator assembly).
Click hereDrivetrain>AXLE AND DIFFERENTIAL>AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Transfer Shift Actuator Assembly) |
Disconnect the C74 transfer shift actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (TM1) - 1 (TM2) | Always | 1.5 to 10 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C61 4 wheel drive control ECU connector.
Disconnect the C74 transfer shift actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C61-8 (TM1) - C74-2 (TM1) | Always | Below 1 Ω |
| C61-7 (TM2) - C74- 1 (TM2) | Always | Below 1 Ω |
| C61-8 (TM1) or C74-2 (TM1) - C61-7 (TM2) or C74-1 (TM2) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C60 4 wheel drive control ECU connector.
Disconnect the C74 transfer shift actuator assembly connector.
w/o VSC:
Disconnect the A68 skid control ECU (brake actuator assembly) connector.
w/ VSC:
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
for 1GD-FTV, 2GD-FTV:
Disconnect the C41 ECM connector.
for 1GR-FE:
Disconnect the G144 ECM connector.
for 2TR-FE:
Disconnect the G142 and G143 ECM connectors.
for 1KD-FTV (Automatic Transmission):
Disconnect the G146 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C60-11 (TL1) - C74-3 (TL1) | Always | Below 1 Ω |
| C60-10 (TL2) - C74-4 (TL2) | Always | Below 1 Ω |
| C60-9 (TL3) - C74-5 (TL3) | Always | Below 1 Ω |
| C74-6 (GND1) - Body ground | Always | Below 1 Ω |
| C60-1 (4WD) - C74-12 (B) | Always | Below 1 Ω |
| C60-3 (4WDL) - C74-9 (L4) | Always | Below 1 Ω |
| C74-10 (GND) - Body ground | Always | Below 1 Ω |
| C60-11 (TL1) or C74-3 (TL1) - Body ground | Always | 10 kΩ or higher |
| C60-10 (TL2) or C74-4 (TL2) - Body ground | Always | 10 kΩ or higher |
| C60-9 (TL3) or C74-5 (TL3) - Body ground | Always | 10 kΩ or higher |
| C60-1 (4WD) or C74-12 (B) - Body ground | Always | 10 kΩ or higher |
| C60-3 (4WDL) or C74-9 (L4) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the transfer shift actuator assembly.
Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY
Check the limit switch, 4WD detection switch and L4 detection switch of the transfer shift actuator assembly.
Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG