The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the timing chain case assembly removal/installation are shown below.
| Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
| Replacement of engine assembly | ·
Injector compensation code registration ·
Pilot quantity learning |
Engine starting |
|
| Clear Crank Time Compensation Data | Engine starting |
|
|
| Replacement of injector assembly | ·
Injector compensation code registration ·
Pilot quantity learning |
Engine starting |
|
·
Replacement of diesel throttle body assembly ·
Replacement of electric EGR control valve assembly ·
Replacement of turbocharger sub-assembly ·
Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor |
Perform initialization | - |
|
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
Make sure foreign matter does not enter the fuel path.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
1.REMOVE ENGINE ASSEMBLY
44763C
2.REMOVE NO. 2 HOSE TO HOSE TUBE
12632
3.REMOVE NO. 2 ENGINE COVER BRACKET
82121
4.REMOVE ENGINE WIRE
17363K
5.REMOVE INTERCOOLER AIR TUBE
26100G
6.REMOVE DIESEL THROTTLE BODY ASSEMBLY
16278
7.REMOVE NO. 2 WATER BY-PASS PIPE
89481B
8.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
89425
9.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
25733A
10.REMOVE NO. 1 VACUUM PIPE (w/ DPF)
25734
11.REMOVE NO. 2 VACUUM PIPE (w/ DPF)
17578B
12.REMOVE PIPE CLAMP (w/ DPF)
12631A
13.REMOVE ENGINE COVER BRACKET
23265C
14.REMOVE GAS FILTER
89421C
15.REMOVE DIESEL TURBO PRESSURE SENSOR
25625
16.REMOVE EGR VALVE BRACKET
25612
17.REMOVE NO. 2 EGR PIPE
16206B
18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
27148A
19.REMOVE CONNECTING WIRE
25601
20.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
25804
21.REMOVE VACUUM CONTROL VALVE SET
16209
22.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
25800
23.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
11409
24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23812D
25.REMOVE NO. 2 FUEL PIPE
26.REMOVE WIRING HARNESS CLAMP BRACKET
17118
27.REMOVE MANIFOLD STAY
22803
28.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY
23243B
29.REMOVE FUEL PUMP MOTOR WIRE
23273H
30.REMOVE NO. 2 FUEL HOSE
23271H
31.REMOVE NO. 1 FUEL HOSE
23804D
32.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)
23815D
33.REMOVE NO. 3 FUEL PIPE (w/ DPF)
23804C
34.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23770
35.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
17111
36.REMOVE INTAKE MANIFOLD
37.REMOVE WIRING HARNESS CLAMP BRACKET
23811H
38.REMOVE NO. 1 FUEL PIPE (w/ DPF)
23760
39.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY
40.REMOVE WIRING HARNESS CLAMP BRACKET
23701
41.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
44781
42.REMOVE HOSE BRACKET
88431
43.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
16282
44.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)
16281
45.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
23295D
46.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)
17168
47.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
89467B
48.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)
17167
49.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17271
50.REMOVE NO. 1 TURBO INSULATOR
51.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY
52.REMOVE EXHAUST PIPE SUPPORT STAY
25051
53.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
12261
54.REMOVE PCV HOSE
16279
55.REMOVE NO. 3 WATER BY-PASS PIPE
16268
56.REMOVE NO. 1 WATER BY-PASS PIPE
16284
57.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
17293
58.REMOVE TURBOCHARGER STAY
15474
59.REMOVE TURBO OIL OUTLET PIPE
15407
60.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
17201
61.REMOVE TURBOCHARGER SUB-ASSEMBLY
16207
62.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
16304
63.REMOVE WATER OUTLET SUB-ASSEMBLY
16321
64.REMOVE WATER INLET
16331A
65.REMOVE THERMOSTAT
16603
66.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.
16620
67.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.
13471
68.REMOVE CRANKSHAFT PULLEY
16575C
69.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
12281A
70.REMOVE NO. 1 ENGINE HANGER
12501
71.REMOVE GENERATOR BRACKET SUB-ASSEMBLY
23670
72.REMOVE INJECTOR ASSEMBLY
23682
73.REMOVE NOZZLE HOLDER GASKET
11301M
74.REMOVE CAMSHAFT POSITION SENSOR
11201
75.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
|
Bolt |
|
Nut |
|
Nozzle Holder Clamp Seat |
Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.
| *1 | Cylinder Head Cover Gasket |
| *2 | No. 2 Cylinder Head Cover Gasket |
| *3 | Camshaft Bearing Cap Oil Hole Gasket |
Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.
12144
76.REMOVE OIL PAN COVER SILENCER
Remove the 5 bolts and oil pan cover silencer from the oil pan sub-assembly.
89491
77.REMOVE ENGINE OIL LEVEL SENSOR
12101
78.REMOVE OIL PAN SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 23 bolts and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.
Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.
Be careful not to damage the cylinder block sub-assembly flange.
16100
79.REMOVE ENGINE WATER PUMP ASSEMBLY
80.SET NO. 1 CYLINDER TO TDC/COMPRESSION
11324
81.REMOVE TIMING CHAIN COVER PLATE
22100
82.REMOVE SUPPLY PUMP ASSEMBLY
22815A
83.REMOVE INJECTION PUMP INSULATOR
11302
84.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 20 bolts from the timing chain cover sub-assembly.
Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.
| *a | Protective Tape | - | - |
Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.
Remove the timing chain case gasket from the timing chain case assembly.
11303A
85.REMOVE FRONT CRANKSHAFT OIL SEAL
| *a | Protective Tape |
| *b | Wooden Block |
Using a screwdriver and wooden block, pull out the front crankshaft oil seal.
Do not damage the surface of the front crankshaft oil seal press fit hole.
86.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR
Using a dial indicator, measure the backlash.
0.02 to 0.3 mm (0.000787 to 0.0118 in.)
0.42 mm (0.0165 in.)
If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.
13519
87.REMOVE OIL PUMP DRIVE GEAR
Remove the oil pump drive gear from the crankshaft.
13566B
88.REMOVE TIMING CHAIN GUIDE
13550
89.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
13559
90.REMOVE NO. 2 CHAIN TENSIONER SLIPPER
13562
91.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13507
92.REMOVE NO. 2 CHAIN SUB-ASSEMBLY
13540
93.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13559
94.REMOVE NO. 1 CHAIN TENSIONER SLIPPER
13561
95.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13506
96.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY
13523
97.REMOVE CAMSHAFT TIMING SPROCKET
11310
98.REMOVE TIMING CHAIN CASE ASSEMBLY
Remove the 15 bolts from the timing chain case assembly.
Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.
| *a | Protective Tape | - | - |
Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.
Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.